Consider a cylindrical rotating machine where the rotor rotates at a rate of 900 rev/min. Air enters the engine at a rate of 11300 L/s from a radial distance of 75cm and exits with a radius equal to 1.3m. The angle of inclination of the flap is 30 ° and the height of the flap is 40 °. If the blade output angle is adjustable, at what output angle range will the engine act as a turbine?

Consider a cylindrical rotating machine where the rotor rotates at a rate of 900 rev/min. Air enters the engine at a rate of 11300 L/s from a radial distance of 75cm and exits with a radius equal to 1.3m. The angle of inclination of the flap is 30 ° and the height of the flap is 40 °. If the blade output angle is adjustable, at what output angle range will the engine act as a turbine?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The first compressor blade pair in a turbojet is to be designed with symmetric blading. If the inflow to the compressor has a gas speed measured as 108m/s, for this speed the shaft is designed to rotate at 262rad/s, and the mean blade radius of this first blade row is 0.51m, to what angle should the first stator be set? Express your answer in degrees.
The impeller of a centrifugal pump is 0.5 m in diameter and rotates at 1200 r .p. m . ; blades are curved back to an angle of 30⁰ to the tangent at outlet tip . If the measured velocity of flow at outlet is 5 m/ sec. If the pump is provided with whirlpool chamber which reduces the velocity of water by 50%. Kinetic energy converted into in whirlpool chamber in j/kg/sec And tangential velocity of runner at outlet
A single stage impulse turbine steam enters with a velocity of 420 m/s and runs at 3300 r.p.m. If the blade speed ratio is 0.44, then the diameter of the wheel in meter will be the diameter of the wheel in meter
The impeller of a centrifugal pump is 0.5 m in diameter and rotates at 1200 r .p. m . ; blades are curved back to an angle of 30⁰ to the tangent at outlet tip . If the measured velocity of flow at outlet is 5 m/ sec. If the pump is provided with whirlpool chamber which reduces the velocity of water by 50%.Net pressure energy at pump outlet *pressure head at impeller outlet And work input /kg of water/sec
Q3// the steam from the nozzle of single wheel impulse turbine discharges with velocity of 600 m/s at angle of 20°. The blade wheel rotates at 3000 rev/min and the mean blade radius is 590mm. the axial velocity of steam at exit from the blade (f.) is 164 m/s and the blades are symmetrical, calculate for 1 kg/s of steam: 1. The blades angles. 2. The blade power. 3. The blade efficiency. 4. The blade velocity coefficient. Answer (28°,126.3 kW, 70% ,0.799)
3. A centrifugal pump impeller runs at 1400 rpm, and vanes angle at exit is 25 degrees. The tangential velocity at exit is 29.33 m/s. Whirl velocity at impeller tip is 23.75 m/s. The impeller has an internal diameter of 0.2 m. Assuming a constant radial flow through the impeller at 2.6 m/s. Calculate: a. The vanes angle at exit b. The angle made by the absolute velocity of water at exit with tangent c. The inlet vane angle d. The work done per kg of water e. Draw the velocity triangle of the system f. Find the impeller external diameter
Problem 1(5): A centrifugal pump transports water between two reservoirs. The pump has an outer diameter of 15 cm, an inner diameter of 8 cm, and a blade width of 2 cm and operates at 1750 rpm. If the water enters the pump axially at ẞ₁ = 45º¸ compute the volume flow rate, Problem 2(10): In the pump of problem 1, the water exits at B₂ 65° when the pump is driven at 1750 rpm. = Compute the minimum power required by the pump?
A centrifugal pump transports water between two reservoirs. The pump has an outer diameter of 15 cm, an inner diameter of 8 cm, and a blade width of 2 cm and operates at 1750 rpm. If the water enters the pump axially at ẞ₁ = 45°, compute the volume flow rate, In the pump of problem 1, the water exits at ẞ₂ = 65° when the pump is driven at 1750 rpm. Compute the minimum power required by the pump?
1 The internal and external diameters of the impeller of a centrifugal pump are 200 mm and 400 mm respectively. The pump is running at 1200 rpm. Forward blades make an angle of 150o at exit and at inlet the angle is 20o. The blade thicknesses at the inlet and outlet are 100mm and 70mm respectively. The hydraulic efficiency of the pump is 87%. Assume the water enters the impeller radially. i Draw neatly the outlet velocity diagram and the inlet velocity diagram. ii Find the Euler power of the pump. iii Find the net Head of the pump. Ans: (ii)140.65W; (iii) 43.42m
- A centrifugal pump with an impeller diameter of 350mm and specific speed of 19.15 and requires 15 kW to discharge 2.4 m³ /min of water, and runs at 1800 rpm. Determine the discharge, head and power required when the pump runs at 2400 rpm. The same discharge could be obtained by altering the impeller diameter without changing the rotational speed for this case find the new diameter of the impeller the head and the power required.
An inward flow reaction turbine, having an inner and outer diameter of 0.45m and 0.90m, respectively. The vanes are radial at inlet and the discharge is radial at outlet and the water enters the vanes at an angle of 12°. Assuming the velocity of flow as constant and equal to 2.8m/s, find the speed of the wheel and the vane angle at outlet. Show schematic diagram and provide solutions.
double sided centrifugal compressor has eye root and tip dia of 18 cm and 30 cm and is to deliver 16 kg/sec air at 16000 rpm. The designed ambient conditions are 15° C and 1 bar and compressor has to be a part of stationary power plant. Determine (1) Suitable value for impeller vane augles of root and tip of eye if the air is given 20° of pre whirl at all radii. Axial component of velocity is constant throughout the impeller and is 150 m/sec. (ii) Max. mach, no. at eye if C,= 1.005 kJ/kg, y=1.4.