Consider a flat plate placed inside a wind tunnel, and air at 1 ATM and 20°C is flowing with a free flow velocity of 60 m/s. What is the minimum length of the plate needed for the Reynolds number to reach 2 × 107? If the critical Reynolds number for external flow is 5 × 105, what type of flow regime would the airflow experience at 0.2 m from the leading edge

Consider a flat plate placed inside a wind tunnel, and air at 1 ATM and 20°C is flowing with a free flow velocity of 60 m/s. What is the minimum length of the plate needed for the Reynolds number to reach 2 × 107? If the critical Reynolds number for external flow is 5 × 105, what type of flow regime would the airflow experience at 0.2 m from the leading edge

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.65P

See similar textbooks

Similar questions

Water at 45.0oC flows over a large plate at a velocity of 30.0 cm/s. The plate is 1.0 m long (in the flow direction), and its surface is maintained at a uniform temperature of 5.0oC. Calculate the steady rate of heat transfer per unit width of the plate. Properties The properties of air at 1 atm and the film temperature of (Ts+T∞)/2 = (5+45)/2 = 25°C are: ρ = 996.6 kg/m3, k = 0.610 W/m.oC, μ = 0.854x10-3 kg/m.s, Pr = 5.85
Air at 20 ◦ C flows inside a pipe 18-mm-ID having a uniform heat flux of 150 W/m 2 on the surface, the average flow velocity at entry being 1.0 m/s. The air pressure is 2 bar. Determine the value of convection coefficient. If the pipe is 2.5 m long, determine the air exit temperature and the wall temperature at the exit. Assume fully developed hydrodynamic boundary layer.
Consider atmospheric air at 25?C and a velocity of 25 m/s flowing over both surfaces of a 1-m-long flat plate that is maintained at 125?C. Determine the rate of heat transfer per unit width from the plate for values of the critical Reynolds number corresponding to 5×105
Example 1 Engine oil at 60°C flows over a 5 m long flat plate whose temperature is 20°C with a velocity of 2 m/s with a surface film temperature of 40°C. The density, thermal conductivity, Prandlt No. and kinematic viscosity are 876 kg/m², 0.144 W/m.K, 28270, and 242 x 10$ m²/s, respectively. Determine the total drag force and the rate of heat transfer per unit width of the entire plate. oil T- = 60°C V-=2 m/s T=20°C- L= 5 m We assume the critical Reynolds number is 5x105. The properties of the oil at the film temperature are:
Q1: In a process water at 30°C flows over a plate maintained at 10 °C with a free stream velocity of 0.3 m/s. Determine the hydrodynamics boundary layer thickness, thermal boundary layer thickness, local and average values of heat transfer coefficient and refrigeration necessary to maintain the plate temperature. Consider a plate of 1m x 1m size. At the film temperature the property values are: Kinematic viscosity 1.006 x 106 m²/s, Thermal conductivity =0.5978 W/m.K, Prandtl number=7.02. =
The air at 1 ATM and 35⁰c flow through a cylinder 5 cm in diameter,at Velocity 50 cm/s. The surface temperature of the cylinder is guarded at 150⁰c *)Calculating heat loss per cylinder unit
Air at 20°C, 1 atm flows with a velocity of 4.5 m/s over a flat plate having a sharp leading edge. The plate surface isothermal at 60°C. (a), determine the following parameters at a distance of 1.89m. i)Local convective heat transfer coefficient (ii)Average convective heat transfer coefficient (iii)The heat transfer rate from both sides per unit width of the plate
Compute the Nu numbers for air at 40°C flowing with 4 m/s speed over the following: 1) A Copper sphere of 5 cm in diameter with 80°C isothermal surface temperature 2) A circular Aluminum pipe of 6 cm in diameter with 80°C isothermal surface temperature 3) A bank of 20x20 5-mm diameter tubes arranged in-line with center-to-center distance of 20 mm. Each tube is assumed to have isothermal temperature of 80°C. Please show detailed calculations.
A 0.5-m diameter uninsulated pipe transports high-temperature steam. Its surface temperature is 150°C and it is exposed to air at -10°C. The air moves in cross flow over the pipe with a velocity of 5 m/s. To compute for the Nusselt number of the air flow, what is the exact value of the temperature in °C on which the air properties should be based?
Experiments have been conducted on a metallic cylinder 12.7 mm in diameter and 94 mm long. The cylinder is heated internally by an electrical heater and is subjected to a cross flow of air in a low-speed wind tunnel. Under a specific set of operating conditions for which the upstream air velocity and temperature were maintained at V = 10 m/s and 26.2°C, respectively, the heater power dissipation was measured to be P = 46 W, while the average cylinder surface temperature was determined to be T, = 128.4°C. It is estimated that 15% of the power dissipation is lost through the cumulative effect of surface radiation and conduction through the endpieces. Thermocouple for measuring airstream temperature Pitot tube for determining velocity Wind tunnel Power leads to electrical heater Heated cylinder Insulated endpiece Thermocouple leads 1. Determine the convection heat transfer coefficient from the experimental observations. 2. Compare the experimental result with the convection coefficient…
8 Air at standard conditions of 1 atm and 27°C flows over a flat plate at 20 m/s. The plate is 60 cm square and is maintained at 97°C. Calculate the heat transfer from the plate.
FUNDAMENTALS OF CONVECTION Consider a flat plate positioned inside a wind tunnel, and air at 1 atm and 20°C is flowing with a free stream velocity of 60 m/s. What is the minimum length of the plate necessary for the Reynolds number to reach 2x107? If the critical Reynolds number is 5x105, what type of flow regime would the airflow experience at 0.2 m from the leading edge? Please, I need the solution from fundamental concepts of how the heat flow behaves in the system. That it be answered with theory of the subject