Consider the circuit drawn below, with current source as shown, the resistances are R₁ = 4, R₂=6.0, and R3 =6 Ohms. What fraction of the source is the current i3 (i.e. find i3/isrc)? D i STC R₁ www {₁ Copyright 230.0 Education. Al Rights Reserved. Rz | - { R₂ Enter your answer to three decimal places, like 5.827. R₂

Consider the circuit drawn below, with current source as shown, the resistances are R₁ = 4, R₂=6.0, and R3 =6 Ohms. What fraction of the source is the current i3 (i.e. find i3/isrc)? D i STC R₁ www {₁ Copyright 230.0 Education. Al Rights Reserved. Rz | - { R₂ Enter your answer to three decimal places, like 5.827. R₂

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 3PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

Question 3: A very simple model for the distribution of clectricity to a typical home is shown in the figure below. Some of components labeled a, b, c, d, c, f, g and h represent the electrical source to the home, some represent the wires that carry the electrical current from the source to the devices in the home requiring electrical power, some represent lamps, televisions, hair dryers and other devices that require power. Assume you are an engineer in charge of a project and one of your subordinate engineers reports that the interconnection in the figure does not pass the power check. The data for the interconnection are given in the table below. Is the subordinate correer? Explain your answer. If the subordinate is correct, find the error in the data. Explain your answer clearly. Based on your answer identify that which label(s) used for the electrical source, wires or other devices. a e h
Question 3 (a) Briefly explain what is the per-unit systero. (b) A resistance of 60n is selected as the base resistance in a circuit consists of three resistors. If R, =1002, R, =30002 and %3D R, = 200 calculate the per-unit vahue of each resistance. %3D (c) A power of, P-25KW and a voltage of, E-2400V are selected as the base power and base voltage of a power system respectively. Calculate the value of the base impedance, Z, and the base current, I,. (d) A resistor bas a per-nnit value of 5.3. Given the base power is P=250KW, and the base voltage is E,-12470V, calculate the ohmic value (actual value) of the resistor. (e) A 4000 resistor caries a cucrent of 60A. Given the base valne of voltage, E, 4KV, the base value of power, P, 500KTF, the base value of current, I, =125.4, and the base value of resistor, 2, = 320 calculate the following: i The per-unit resistance. ii. The per-unit current. ii. The per-unit voltage across the resistor. iv. The per-unit power.
Subject: Circuits show your solution and check the multiple choice choose one
please sketch them all and show a step by step solution
c). write the current equation for the circuit below 60 mA 20 mA 14 Is 40 mA 30 mA Determine the missing currents from the equation in c).
In a series circuit, certain general rules may be stated with regard to quantities of voltage, current, resistance, and power. Express these rules, using your own words: "In a series circuit, voltage..." "In a series circuit, current..." "In a series circuit, resistance..." "In a series circuit, power..." For each of these rules, explain why it is true.
Three resistors of 10, 12 and X ohms, respectively are connected in parallel across a constant current source of 8A. Determine "X" if this resistor draws 2.13333333... A.
Basic Electrical EngineeringDraw symbols of electrical components. Note: You may use both IEC and NEMA symbols. - Conductors crossing but not connected- Conductors crossing and connected - DC source other than battery- DC generator- AC voltage source- Ideal current source- Ideal Voltage Source- Current Controlled Current Source- Current Controlled Voltage Source- Voltage Controlled Current Source - Voltage Controlled Voltage Source
please have step by step solution and explain
Suppose the three branch currents in this circuit are I₁ = -3 A, I₂ = -18 A, and I3 = -15 A. The voltage drop across each circuit element is as given in the table below. From this information, determine, for each of these circuit elements, (i) whether an active or passive sign convention is being used for that element, (ii) whether that element is absorbing or producing a net (positive) amount of electrical power. In each answer box within the table below, type the correct choice from among the bold-faced words above. V₂ B A B A C D 1₁ A B 1₂ 1₂ + Circuit element Voltage drop Sign convention? Absorbing or producing net electrical power? -9 V -2 V C 9 V -11 V D
Determine the current Ic, current at the resistor, and current supplied by the voltage source. Note: you must put the imaginary part of the reactances and its sign
For the network shown in figure (3), if the switch is closed for 2usec and then opened for Susec, find mathematical expressions for vi and in of both periods of time and then plot the waveforms of vL and i as a function of time.