Consider the figure on the right. A steel plate is used to connect a member to a steel column. 5 - 32 mmø steel bolts are used as fasteners. 1. If P-10 kN determine the average shearing stress on the bolts.** 2. If the allowable shearing stress on the bolts is 60MPA, determine the maximum safe value of P.*

Consider the figure on the right. A steel plate is used to connect a member to a steel column. 5 - 32 mmø steel bolts are used as fasteners. 1. If P-10 kN determine the average shearing stress on the bolts.** 2. If the allowable shearing stress on the bolts is 60MPA, determine the maximum safe value of P.*

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

What is the safe load "P" that can be transmitted by the fillet-weld joint shown in figure below if allowable shear stress in the fillet weld is 108 MPa and F.O.S. for load is 1.5? P4 www 60mm 777 50mm 8mm P
STAGGERED CONNECTIONS: A PLATE WITH WIDTH OF 400 mm AND THICKNESS OF 12 mm IS TO BE CONNECTED TO A PLATE OF THE SAME WIDTH AND THICKNESS BY 34 mm DIAMETER BOLTS, AS SHOWN IN THE FIGURE. THE HOLES ARE 2 mm LARGER THAN THE BOLT DIAMETER. THE PLATE IS A36 STEEL WITH YIELD STRENGTH Fy = 248 MPa. ASSUME ALLOWABLE TENSILE STRESS ON NET AREA IS 0.60Fy. IT IS REQUIRED TO DETERMINE THE VALUE OF b SUCH THAT THE NET WIDTH ALONG BOLTS 1-2-3-4 IS EQUAL TO THE NET WIDTH ALONG BOLTS 1-2-4. a. CALCULATE THE VALUE OF b IN MILLIMETERS. b. CALCULATE THE VALUE OF THE NET AREA FOR TENSION IN PLATES IN SQUARE MILLIMETERS. c. CALCULATE THE VALUE OF P SO THAT THE ALLOWABLE TENSILE STRESS ON NET AREA WILL NOT BE EXCEEDED.
A plate with width of 420 mm and thickness of 13 mm is to be connected to a plate of the same width and thickness by 30 mm diameter bolts, as shown in the Figure 1. The holes are 3mm larger than the bolt diameter. The plate is A36 steel with yield strength Fy = 248MPa. Assume allowable tensile stress on net area is 0.60Fy. It is required to determine the value of b such that the net width along bolts 1-2-3-4 is equl to the net width along bolts 1-2-4. W = 420 mm t = 13 mm a = 64 mm c = 104 mm d = 195 mm Bolt Diameter = 30 mm Holes Diameter = 30 mm + 3 = 33 mm ?? = 248 MPa Allowable Tensile Stress on ?? = 0.60Fy a. Calculate the vaue of b in millimeters. b. Calculate the value of the net area for tension in plates in square millimeters. c. Calculate the value of P so that the allowable tensile stress on net area will not be exceeded.
P4.002 Three bolts are used in the connection shown in the figure. The thickness of plate (1) is 15 mm. The ultimate shear strength of the bolts is 350 MPa, and the ultimate bearing strength of plate (1) is 375 MPa. Determine the minimum bolt diameter required to support an applied load of P = 155 kN if a minimum factor of safety of 2.8 is required with respect to both bolt shear and plate bearing failure. Answer: dbolt min = (1) mm
I need a clear answer by hand, not by keyboard and fast answer within 20 minutes. Thank you | dybala For the beam loaded as shown, find the maximum tensile and compressive bending stresses and maximum shearing stress.. IN.A=4*10mm* 80mm 100mm 60mm 60mm 1.5KN 2kN/m 1mal A |-----|- | Im ++ Im->> 3m 3kN/m
Determine the design tensile strength of the 12 in. x 1/2 in. steel plate shown in the figure. The bolts are 3/4 in. diameter. The steel is A572 Gr. 50. Check yielding and fracture. Check Block Shear. T 3in. 73im 13in 1 3in t
From the bolted connection shown, the diameter of bolts is 20 mm with the hole diameter equal to 3mm larger than the bolt diameter, the angular section is 100x75x8mm, with an area of 1340 mm^2. Thickness of gusset plate is 9 mm. the gusset plate. (a)If T = 200KN, compute the shearing stress on the bolts. (b)If the allowable shearing stress on the bolt is 145MPa, compute the value of T.
9. The gusset shown is riveted to the column flange by 7-20mm diameter rivet single shear. Determine the stress in the most heavily loaded bolt. If the design shear stress is 400MPA, determine the ultimate load that the connections can carry. Using the design shear stress how much more torque can the connections carry? 140 kN 200 mm 175 mm 7- 20 mm bolts 150 mm 150 mm 150 mm
A flanged bolt coupling consists of 6 - 12 mm - diameter bolts on a bolt circle of 320 mm in diameter. Compute the number of additional 10 mm - diameter bolts on a bolt circle 200 mm in diameter to increase the torque capacity to 7.65 kNm. The shearing stress of the bolts should not exceed 60 MPa. Select one: O a. 6 bolts O b. 4 bolts O c. 3 bolts O d. 2 bolts NEXT PAGE
Situation 8: For the connection shown in the figure. Pu = 80 KN, x1 = 200, x2 = 100, y1 = 50, y2 = y3 = y4 = 100 y1 y2 y3 y4 O 80 MPa O 71 MPa O 74 MPa oooo O 86 MPa O 1. Which of the following nearly gives the shearing stress of the most stress bolt? Use 20 mm diameter bolt. x1 O O O x2
Two bolts are used to lap points two steel plates. Tensile force on the plate is 45kN. Determine the required diameter of the bolts if the failure shear stress of the bolts is 350 MPa. Use a factor of safety for shear equal to 2.0
The bolted connection shown must support an applied load of P = 5300 kN. The average shear stress in the bolts must be limited to 250 MPa. Determine the minimum bolt diameter that may be used in the connection. Answer: Minimum bolt diameter = i mm