Consider the following figure. (Assume V = 19.0 V, R₁ = 1.50, and R₂ = 6.00 £2.) R₁ + 3.00 Ω www 4.00 Ω R₂ (a) Is it possible to reduce the circuit shown in the figure above to a single equivalent resistor connected across the battery? Explain. This answer has not been graded yet. (b) Find the current in the 1.50-2 resistor. A (c) Calculate the power delivered by the battery to the circuit. W

Consider the following figure. (Assume V = 19.0 V, R₁ = 1.50, and R₂ = 6.00 £2.) R₁ + 3.00 Ω www 4.00 Ω R₂ (a) Is it possible to reduce the circuit shown in the figure above to a single equivalent resistor connected across the battery? Explain. This answer has not been graded yet. (b) Find the current in the 1.50-2 resistor. A (c) Calculate the power delivered by the battery to the circuit. W

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter10: Direct-current Circuits

Section: Chapter Questions

Problem 69AP: Consider the circuit below. The battery has an emf of = 30.00 V and an internal resistance of r =...

See similar textbooks

Similar questions

A 12.0-V emf automobile battery has a terminal voltage of 16.0 V when being charged by a current of 10.0 A. (a) What is the battery’s internal resistance? (b) What power is dissipated inside the battery? (c) At what rate (in °C/min ) will its temperature increase if its mass is 20.0 kg and it has a specific heat of 0.300 kcal/kg • °C, assuming no heat escapes?
A child's electronic toy is supplied by three 1.58-V alkaline cells having internal resistances of 0.0200 inseries with a 1.53-V carbon-zinc dry cell having a 0.100- internal resistance. The load resistance is 10.0 . (a) Draw a circuit diagram of the toy and itsbatteries, (b) What current flows? (c) How much power is supplied to the load? (d) What is the internal resistance of the dry cell if it goes bad, resulting in only 0.500 W being supplied to the load?
A battery has an emf of 15.0 V. The terminal voltage of the battery is 11.6 V when it is delivering 20.0 W of power to an external load resistor R. (a) What is the value of R? (b) What is the internal resistance of the battery?
An automobile starter motor has an equivalent resistance of 0.0500 and is supplied by a 12.0-V battery with a 0.0100- internal resistance, (a) What is thecurrent to the motor? (b) What voltage is applied to it? (c) What power is supplied to the motor? (d) Repeat these calculations for when the battery connections are corroded and add 0.0900 to the circuit. (Significant problems are caused by even small amounts of unwanted resistance in low-voltage, high-current applications.)
A 20.00-V battery is used to supply current to a 10-k resistor. Assume the voltage drop across any wires used for connections is negligible, (a) What is the current through the resistor? (b) What is the power dissipated by the resistor? (c) What is the power input from the battery; assuming all the electrical power is dissipated by the resistor? (d) What happens to the energy dissipated by the resistor?
A student makes a homemade resistor from a graphite pencil 5.00 cm long, where the graphite is 0.05 mm indiameter. The resistivity of the graphite is =1.38102/m . The homemade resistor is place inseries with a switch, a 10.00-mF capacitor and a 0.50-V power source, (a) What is the BC time constant of the circuit? (b) What is the potential drop across the pencil 1.00 s after the switch is closed?
For the network in Figure P18.60, show that the resistance between points a and b is Rab=2717. (Hint: Connect a battery with emf across points a and b and determine /I, where I is the current in the battery.) Figure P18.60
Explain why R=R0(1 + a?T) for the temperature variation of the resistance R of an object is not as accurate as P=P0(1 + a?T) which gives the temperature variation of resistivity P.
The power dissipated in a resistor is given by P = V2/R, which means power decreases if resistance increases. Yet this power is also given by P = I2R, which means power increases if resistance increases. Explain why there is no contradiction here.
Consider the circuit below. The battery has an emf of = 30.00 V and an internal resistance of r = 1,00 . (a) Find the equivalent resistance of the circuit and the current out of the battery. (b) Find the current through each resistor, (c) Find die potential drop across each resistor, (d) Find the power dissipated by each resistor, (e) Find the total power supplied by the batteries.
The resistors network shown below. Take R1 = 12 Ω, R2 = 4 Ω, R3 = 1 Ω, R4 = 6 Ω, R5 = 3 Ω and ε = 36 V. The equivalent resistance (Req) and the current through R2 (I2), (Req, I2) is A. (28 Ω, 1.3 A) B. (6 Ω, 4.5 A) C.(28 Ω, 1.0 A) D.(4 Ω, 2.0 A) E.(6 Ω, 6.0 A) F.(4 Ω, 1.0 A)
In the circuit shown below E = 75.0 V, R5 = 4.0o n, R3 = 2.00 n, R2 = 2.20 n, Iş = 8.40 A, I4 = 5.50 A, and I = 11.0 A. Find the current through Rz and R3, and the values of the resistors R, and Ra. Iz = I3 = A R1 = R. = R4 ww Is ww