Consider the following step up converter with a resistive load of value R=5 ohms. It is supplied by a DC power source of magnitude Vs=200 V. The switching frequency is 5 kHz and the duty cycle k is first set to 0.5 and the inductance used within the circuit has a value of L=10 mH. The switch is supposed to be ideal. If the minimum and maximum currents in mode 1 and mode 2 are respectively 79A and 81 A, then the average supply current is: Select one: Oa. Is 80 A b. Is = 160 A Oc. Is = 81 A O d. Is = 40 A

Consider the following step up converter with a resistive load of value R=5 ohms. It is supplied by a DC power source of magnitude Vs=200 V. The switching frequency is 5 kHz and the duty cycle k is first set to 0.5 and the inductance used within the circuit has a value of L=10 mH. The switch is supposed to be ideal. If the minimum and maximum currents in mode 1 and mode 2 are respectively 79A and 81 A, then the average supply current is: Select one: Oa. Is 80 A b. Is = 160 A Oc. Is = 81 A O d. Is = 40 A

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 7RQ: An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a...

See similar textbooks

Similar questions

An unipolar PWM full bridge circuit has a Vr.rms of 125V at a duty cycle D1 of 0.7. What is Vd? What is Vo.rms?
A buck converter, as shown in Figure (a) below, is working in steady state. The output voltage and the inductor current can be assumed to be ripple free. Figure (b) shows the inductor voltage Vi during a complete switching interval. Assuming all devices are ideal, the duty cycle of the buck converter is M VA 30 V- DA R TON TOFF (a) -20 V- (b)
What is the importance of the charecteristic curve in PN Junction
The anode of a diode is connected to one terminal of a 1-KΩ resistor. The other terminal of the resistor is connected to the ground and the negative terminal of a 12-volt DC source is also grounded. The three components are connected in series. How much is the load current with the ideal diode?
A single phase full converter feeds power to RLE load with R=10 ohm, L=10 mH and E=50 V, the ac source voltage is 230 V, 50 Hz. For continuous conduction, what is the average value of load current for firing angle delay of 600 ?
6. A 1-phase full converter delivers ripple free current to RL load with R=1592. The source voltage is 230V, 50Hz, for a=30°. Determine rectification efficiency, voltage ripple factor displacement factor, and power factor
Calculation for DC Equivalent Circuit and ac Equivalent Circuit
With V1, voltage peak to peak is 10 volts, R1=200 Ohm, R2=1000 Ohm and C1= 300 nF. Find Vx, voltage across the the capacitor, C1 and R2 when the frequency is 1000 Hz and 10000 Hz
For the following circuit if the secondary voltage of the transformer is 15V rms, what are the output voltage and the PIV of the diodes Vm D2 D3 C4 + 2V
Zener Diodes: In the following diagram, Iz = 0.5 mA, Vz = 5, rz = 30 ohms. What is Vout? What is the current through D5? Current through D7?
Calculate the peak-to-peak inductor current ripple (in amperes) of a Buck converter assuming it operates in continuous current conduction mode. Circuit parameters are: Input voltage Vdc = 38 V, output voltage Vo = 17 V, PWM frequency fpwm = 50 kHz, inductor value 328 µH and capacitor value C = 10 µF. is S iL L I₂ Vac VA D VL ic C R₁ Please specify your answer in units of A to 2 decimal places. V
A three phase full wave rectifier is shown below. The input phase voltage peak is Vm=311.128 V. The load is purely resistive of value 52. The DC and RMS output voltages are respectively equal to: Secondary 太D太D,太D, 太D。太De太D, b. Select one: O a. 180V, 240.2V O b. 514.6V, 515.04V O c. 180V, 197.2V O d. 220V, 249.2V