Consider the graph below for 3 metals which have been cold-worked. From the graphs, which of the following statements are true?Stress &Strain &O c.ABSelect one or more:O a. B and C have similar hardness; C has greater brittlenessO f.b.A and B have similar hardness; A has greater brittlenessCA is harder than C and is less ductileOd. B is harder than C but has nearly similar ductilityO e.B is softer than C and has nearly similar ductilityA is harder than C and is more ductile

Answered: Image /qna-images/answer/2675c856-f126-485b-bf74-ee66bf7875ac.jpg

Answered: Consider the graph below for 3 metals…

Consider the graph below for 3 metals which have been cold-worked. From the graphs, which of the following statements are true? OSS A B C

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Tag question Consider the graph below for 3 metals which have been cold-worked. From the graphs, which of the following statements are true? Stress Select one or more: a. C. Strain & A e. B C b. B and C have similar hardness; C has greater brittleness B is softer than C and has nearly similar ductility A is harder than C and is more ductile d. A and B have similar hardness; A has greater brittleness A is harder than C and is less ductile f. B is harder than C but has nearly similar ductility 5 up i A C
Using the tensile test simulation tool, a. generate the stress-strain curve for aluminum b. Indicate the following points in the stress-strain curve for aluminum and give the corresponding values: limit of proportionality elastic limit 0.2% offset yield stress (include the graph illustrating how this was determined) ultimate stress fracture stress c. Calculate modulus of elasticity. d. compare aluminum with nylon (include the related graph) and answer the following: Which has higher tensile strength? Provide the necessary values to support the answer. Which is stiffer? Support your answer with calculations.
Fill in the blanks: A tensile test is carried out to determine the strength constant C and strain-rate sensitivity exponent m for a certain metal at 1000°F. If temperature were decreased to 900°F, the strength constant C would . .and the strain- rate sensitivity exponent m would. . Select one: a. C would stay constant, m would Decrease b. Nothing would change c. C would Increase, m would Decrease d. C would Increase, m would stay constant e. C would Decrease, m would Increase
1. A bronze alloy specimen having a diameter of 12.8 mm and a gage length of 50 mm was tested to fracture. Stress and strain data obtained during the test are shown in Figure. Determine: 400 Upper scale a. the modulus of elasticity. b. the proportional limit. c. the ultimate strength. 320 Lower scale 240- d. the yield strength (0.20% offset). 160 e. the modulus of resilience. f. the true fracture stress if the 80 final diameter of the specimen at the location of the fracture was 10.5 mm. 0.100 0.200 0.300 0.400 0.005 0.010 0.015 0.020 g. The Poisson's ratio. Strain (mm/mm) Stress (MPa)
Q4 Answer with True or Fales and re-write the sentence with correction for 10 only ( 1- Mn Ni Cr, W, Mo, V are the most important elements that forming Austenite. 2- Diamond Pyramid is used for the Scale C in Rockwell hardness test. 3- The stress of forming process must exceed UTS yield point. 4- The brittle transition temperature of steel is within -4 °C to 4°C. 5- Quenching process for steel is used to increase the ductility. 6- The annual quantity production of high production process is more than ten thousand. 7- Knoop test method is used to test the thick and hard material with little load.
Q4 Answer with True or Fales and re-write the sentence with correction for 10 only 1- Mn Ni Cr, W, Mo, V are the most important elements that forming Austenite. 2- Diamond Pyramid is used for the Scale C in Rockwell hardness test. 3- The stress of forming process must exceed UTS yield point. 4- The brittle transition temperature of steel is within -4 °C to 4°C. 5- Quenching process for steel is used to increase the ductility. 6- The annual quantity production of high production process is more than ten thousand. 7- Knoop test method is used to test the thick and hard material with little load. 8- The purpose of the addition of S to steel with 0.5% is to improve the machinability of steel. 9- The series 4 of Aluminum alloy refer to the presence of Cu as main alloying element. 10- Construction steel with 0.2-0.3% C has higher strength and higher ductility. 11- Austenitic Stainless Steel: contain 16-26 % Cr.
As the tempering temperature of a heat treated steel increases the associated values of Brinnell hardness also increase, while the values of tensile strength and yield strength decrease. True or false
Q3b. The stress-strain characteristic curves for materials A, B and C are shown below. Which one statement most accurately describes the relative toughness and ductility for materials A, B & C? Material A Material B Material C Strain Select one: a. Material A has low toughness, Material B has high ductility and Material C has low toughness. b. Material A has high toughness, Material B has low ductility and Material C has low toughness. c. Material A has low ductility, Material B has low toughness and Material C has low toughness. d. Material A has high ductility, Material B has low toughness and Material C has high toughness. Stress
Question : Explain key assumptions in the theory of simple stress. Explain different parts of a characteristic stress-strain daigram of steel.(draw labeled and clean diagram)
Quèstion 3 4 p From the following figure shows the tensile stress- strain curve for a plain-carbon steel. What is its modulus of elasticity? 600 MPa 600r 10 psi 50 60 400 400 40 20 100 0.05 0.10 0.15 Stain O A. 320 GPa O B. 500 GPa OC.400 GPa O D.215 GPa Sem (MP
O) In Figure show the fatigue curve for a metal. a) If a sample was taken from this material with diameter 5mm and tested on fatigue device under constant load 29,4 N far 125.2 mm from the specimen. Find the critical number of cycle in revolution ? b) Find the endurance limit for this material. 500 (ee 200 leo 4. 6 7 2. No.of cycles (logM) stress N/mm
Draw two schematic graphs using pencil showing a typical stress-strain curve for aluminum. The first graph should show engineering stress vs engineering strain, and the second graph should show true stress vs true strain. Label the showing: (i) elastic modulus (ii) proportional limit (iii) yield stress (iv)yield strain (v) fracture stress (vi) fracture strain on each graph. You may showboth graphs on one plot. Explain the difference between engineering stress and true stress.