Convolution is a mathematical operation that expresses a relationship between an input signal, the output signal, and the impulse response of a linear-time invariant system. Three systems that represented by the impulse response, ħ[n], ha[n] and ħa[n] are connected in series as shown in Figure Q2(a), where x[n] and y[n] are the input and output signals respectively. The impulse response functions of each system are represented by equation (1). (2) and (3). h,[n] = 2nu[n + 3] – 2nu[n – 3] h2[n] = 6[n – 2] ha[n] = S[n + 2] - 28[n – 2] %3D x[n] h,[n] ħ[n] h[n] →y[n] Figure Q2(a) (a) Using the convolution, sketch the output response of y[n] if the input signal is given by x[n] = 6[n].

Convolution is a mathematical operation that expresses a relationship between an input signal, the output signal, and the impulse response of a linear-time invariant system. Three systems that represented by the impulse response, ħ[n], ha[n] and ħa[n] are connected in series as shown in Figure Q2(a), where x[n] and y[n] are the input and output signals respectively. The impulse response functions of each system are represented by equation (1). (2) and (3). h,[n] = 2nu[n + 3] – 2nu[n – 3] h2[n] = 6[n – 2] ha[n] = S[n + 2] - 28[n – 2] %3D x[n] h,[n] ħ[n] h[n] →y[n] Figure Q2(a) (a) Using the convolution, sketch the output response of y[n] if the input signal is given by x[n] = 6[n].

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

If there is a unit step function at the input of the circuit above and R=61 and C=1/61, which of the following statements is incorrect for the output waveform. A)There is a 180 degree phase difference between the input and the output. b)The output is in triangular waveform. c)Its amplitude is "1". d)At t=0 there is a unit impulse (impulse) sign. e) There are positive and negative alternans (half regions) in the output wave.
If there is a unit step function at the input of the circuit above and R=6 and C=1/6, which of the following statements is incorrect for the output waveform? A) There are positive and negative alternans (half regions) in the output wave. B) At t=0 there is a unit impulse (impulse) sign. C) There is a 180 degree phase difference between the input and the output. D) Output is in triangular waveform. E) Its amplitude is "1".
2. A discrete-time signal x[n] is shown in Figure 2 x[n] -3 -2 -1 0 1 2 3 4 5 6 Figure 2 Sketch and carefully label each of the following signals: x [n - 2] x [4 - n] x [2n]
Answer the following questions: a)" 1 Given the output voltage signal Vo(s) below, find the output voltage in the time domain vo(t). 2 Vo(s)= (s+2)(s+8) b) Discuss the application of Ohm's Law for a given R and C in series in both time and frequency domains. Files You can drag and drop files here to add them. Next page
Hi, I'm stuck with this problem. Can you help me to solve it? In order for me to understand the theory behind it, could you also tell me where I can find this topic? Here is the problem: Two resistors RAB and RAC, connected in series, form a potential divider with inputterminals A and C and output terminals B and c.(a) Sketch the circuit(b) If RAB is 10 kohm and RBC is 1500 ohm, determine the ratio of VBC / VAC when the inputresistance of a meter connected between B and C is(i)infiniteand (ii)1000 ohm(c) If the maximum permitted power dissipation in RAB is 15W and in RBC 1W, determine themaximum voltage VAC across which the divider/1000 ohm meter combination may be connected.
i have already asked this question twice and it was solved incorrectly. given the transfer function solve the question. the answer should be v0(t)=5radical2 cos(3t-3/4pi) solve it and please do not submit ur answer unless it is completely identical to the one i've given. and please solve in detail and explain it step by step as if you're explaining to a newbie and if correct ofcourse i'll give a thumbs up. thank you!
Question 3: Design the values of Kl and K2 for the system shown below to meet the following specifications: (i) (ii) steady-state error component due to a unit step disturbance is - 0.000012 and steady-state error component due to a unit ramp input is 0.003. D(s) R(s) + K1(s + 2) K2 C(s) (s + 3) s(s + 4)
Draw the output waveforms (S, X, and Y) for the below sequential circuit by assuming the propagation delays of all the components that are shown in below figure equal to zero second. A- clk A B B Clk D Q C S -Y X
• For the unit step response shown in the figure, find the transfer function of the system. 0.05 0.1 0.15 0.2 0.25 Time (seconds) Response
The following plot is a step response of a sixth order system. 1. Find the time domain specifications i.e. Tp. Tri. T. and P.O. 2. Find a second order system whose response matches the given response in the following sense a. The percentage overshoot and rise time b. The peak time and settling time c. The rise time and settling time You have to find three systems Aroude 1 14 13) 12 UP E ON ST 06 0.5 DA 03 63 DI 0 6 A W . -CA P.O.= e √1-2 Ts= 4 ζωη Satisfying 2% criteria 10 Control Systems Homework Problem 3 100 M 16 18 20 Step Response for 24 21 20 30 The P.O. -In (100) √²+In² (²00) Tr Tp 2.16+0.60 On 0.3<≤0.8 Onv T 1-32 and 10% to 90% value
b) Create a new folder name Lablb in your D:\Student_Matric_Number. Find the output X and show the simulation waveform. A B
(a) A discrete-time signal x[n] is shown in Figure 1. x[n] 3 1 -1 Figure 1: Discrete-time Signal x[n] (i) Sketch and label x[2n] - x[n- 1] (ii) Sketch and label 2x[n]{u[n] - u[-n] }