Swit to also dutJo Crven2Assembly consist of a spel ( Es = 200 GPd, As = 1500 mm ² ) Kod AB anda brass ( E₂²100 GP ae B² Esplare BАВ= 2000 мм.is used to apply the 400 ka load and is assumed rigid.MY THANSpikerJuden to-AMy wederofind average normal stress in sizel rod (unir MPa)normal stress in brass (umrmpa)andaverage2200. [kN]-Steel200. [kN]-1.500 [m]) rod BC.B?.BrassC|-1.000-1.000 [m]→

Answered: Image /qna-images/answer/7656d260-7908-484d-b731-9346c6a4c7e4.jpg

Crven Assembly consist of a sibel ( Es = 200 Gpd As = 1500 mm ² ) Kod AB and a brass ( GPa EB²=100 e B². 75 plate Hot on to th →) find and A 1 used to apply the 400k * load and is a sumed rigid. Spaber 7 And average 2 AB= 2000 mm ² ) rod BC. average 106-2209) • NAS normal stress in steel rod (unir MP4 normal stress in 200. [kN]- Steel 200. [kN]- 1.500 [m] stress in brass (unit MPa) B Brass C 1.000 [m]→→

Crven Assembly consist of a sibel ( Es = 200 Gpd As = 1500 mm ² ) Kod AB and a brass ( GPa EB²=100 e B². 75 plate Hot on to th →) find and A 1 used to apply the 400k * load and is a sumed rigid. Spaber 7 And average 2 AB= 2000 mm ² ) rod BC. average 106-2209) • NAS normal stress in steel rod (unir MP4 normal stress in 200. [kN]- Steel 200. [kN]- 1.500 [m] stress in brass (unit MPa) B Brass C 1.000 [m]→→

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.15P: A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded...

See similar textbooks

Similar questions

The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
An elevated jogging track is supported at intervals by a wood beam AB (L = 7.5 ft) that is pinned at A and supported by steel rod BC and a steel washer at B. Both the rod (dBC= 3/16 in.) and the washer (dB= 1.0 in.) were designed using a rod tension force of TBC=415 lb. The rod was sized using a factor of safely of 3 against reaching the ultimate stress tru— 60 ksi. An allowable bearing stress sba= 565 psi was used to size the washer at B. A small platform HF is suspended below a section of the elevated track to support some mechanical and electrical equipment. The equipment load is uniform load q = 50 lb/ft and concentrated load WE= 175 lb at mid-span of beam HF. The plan is to drill a hole through beam ABaX £land install the same rod (dBC) and washer) dB) at both D and F to support beam HF. (a) Use s and to check the proposed design for rod DF and washer d,: are they acceptable? (b) Re-check the normal tensile stress in rod BC and bearing stress at 8 if either is inadequate under the additional load from platform HF. Re-design them to meet the original design criteria.
A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?
- A specimen used in a coupon test has norm al stress ??. = 15 MPa (see figure). Using Mohr’s circle, find the state of stress on the element oriented at angle ? = 20° and show the full stress state on a sketch of a properly oriented element.
A scuba t a n k (see fig ure) i s bci ng d e signed fo r an internal pressure of 2640 psi with a factor of safety of 2,0 with respect to yielding. The yield stress of the steel is 65,000 psi in tension and 32,000 psi in shear, (a) If the diameter of the tank is 7,0 in., what is the minimum required wall thickness? (b) If the wall thickness is 0.25 in., what is the maximum acceptable internal pressure?
Repeat Problem 11.2-14 using L = 12 ft, ß = 0.25 kips/in., ßRl= 1.5ßL2, and ßR2= 2 ßR1.
A copper alloy pipe with a yield stress aY= 290 MPa. is to carry an axial tensile load P = 1500 kN (see figure part a). Use a factor of safety of 1.8 against yielding. (a) If the thickness t of the pipe is one-eighth of its outer diameter, what is the minimum required outer diameter dmin? (b) Repeat part (a) if the tube has a hole of diameter dt 10 drilled through the entire tube, as shown in the figure part b.
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
An aluminum tube is required to transmit an axial tensile force P = 33 k (sec figure part a). The thickness of the wall of the tube is 0.25 in. (a) What is the minimum required outer diameter d minif the allowable tensile stress is 12.000 psi? (b) Repeat part (a) if the tube has a hole of a diameter J/10 at mid-length (see figure parts b and C).
Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
ero Stiven: A 2 in diameter Red 180 in long elongares 0.12 in under load of 60 kip. The diamurer of Rod decrease 0.004 in during looding 2 and Transverse strain ? Rind average normal stress t qui't is ksi
EHide bl OP=287 N OP=573 N Let's consider a rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E = 200 Gpa and a Poisson's ratio of 0.3. If a tensile force F is subjected to that rod cross-section, the diameter becomes 3.998 mm. determine the applied force F. Select one: OF=10472 N OF=15708 N OF=6283 N O F= 4189N F = 13090 N OF= 5236 N Finish attempt.. US ACTIVITY O Test-Spring 2020-2021 Jump to...