D 2 ft -2 ft- -2 ft A 90 65 200 lb 100 lb 2. A beam AB is loaded as shown. The beam is pin-connected to the wall at A. At Ba 10-inch diameter pulley is attached through frictionless bearing to the beam. A rope passes around the pulley and is connected to C and D vertically above the extremities of the horizontal diameter of the pulley. Determine the pin reaction at A and the tension in the rope. Hint: Pin connection has vertical and hozirontal reactions. B.

D 2 ft -2 ft- -2 ft A 90 65 200 lb 100 lb 2. A beam AB is loaded as shown. The beam is pin-connected to the wall at A. At Ba 10-inch diameter pulley is attached through frictionless bearing to the beam. A rope passes around the pulley and is connected to C and D vertically above the extremities of the horizontal diameter of the pulley. Determine the pin reaction at A and the tension in the rope. Hint: Pin connection has vertical and hozirontal reactions. B.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 200 Ib weight is suspended as shown. Wires DE and BC (Ewire = 29,000 ksi) have a 0.05" diameter. Bar DA is rigid and A is a pin connection. Determine the downward motion of the weight when it is attached to the cable at Cand released. The wires are straight and the rigid bar DA is horizontal before the weight is attached. 3ft 4 f
A solid 1.00-in.-diameter steel [G = 12000 ksi] shaft is subjected to the torques shown. Determine the rotation angle of pulley D with respect to the support at A. (1) 240 lb-ft 36 in. O-0.0653 rad O-0.0513 rad O-0.0415 rad O-0.0542 rad O-0.0316 rad B (2) 36 in. 215 lb-ft (3) 36 in. 110 lb-ft D
4-91. If the couple moment acting on the pipe has a magnitude of 300 Nm, determine the magnitude F of the forces applied to the wrenches. -F A -150 mm -150 mm. B F 200 mm Probs. 4-90/91 600 mm A CO
The frame shown below is subjected to an applied Point Load of 27kN and a Uniformly Distributed Load of 3kN/m and is supported at A by a pinned connection and at B by a roller connection. Calculate the vertical support reaction at B. Give your answer in kN to 2dp. 3m 3m PL UDL 5m A
F8-9. Blocks A and B have a mass of 7 kg and 10 kg. respectively. Using the coefficients of static friction indicated, determine the largest force P which can be applied to the cord without causing motion. There are pulleys at C and D. 300 mm No fuidhon at The pulleys D 400 mm B PAB-0.3 A C 0.1 P
The solid 32 mm diameter steel [E - 200 GPa] shaft supports two belt pulleys. Assume that the bearing at B can be idealized as a roller support and that the bearing at D can be idealized as a pin support. For the loading shown, determine: (a) the shaft deflection at pulley A. (b) the shaft deflection at pulley C. Assume P- 500 N, Q- 950 N, Las - 450 mm, Lạc - 650 mm, Lco - 650 mm. A B C D LAB LBC LCD Part 1 Calculate the area moment of inertia for the solid circular cross-section. Answer: |- i mm4
In the assembly shown. the block has a weight w = 200 lbs and the cord is attached to the pin at B. The pulleys have radi of rt = 2 Tn. and r2 1 În. Neglect the mass of the pulleys and the link. Pulley Pulley A 45 12 Compute the reaction at the ĩnk AB In lbs." 250 260 280 B.
The rigid beam is supported by a pin support at A and steel wires BD and CE (E-200GPA). The steel wires are 1cm in diameter. If the load P is 5kN and the weight of the beam is neglected, solve the tension at wire BD. E 4 m 3 m 2 m 2 m O 1.95kN O 1.64kN O 0.91kN O 1.29KN o o oO
To test the deflection of the uniform 200-lb beam the 120-lb boy exerts a pull of 40 lb on the rope rigged as shown. Compute the force supported by the pin at the hinge O. -2 6' A 2+ ←2-
Replace the loading by an equivalent force and couple moment acting at point O.
*R9 4. Two A36 steel pipes, cach having a cross-sectional area of 200 mm, are screwed together using a union at B as shown. Originally the assembly is adjusted so that no load is an the pipe. If the union is then tightened so that its screw, having a lead of 0.55 mm, undergoes two full turns, determine the average normal stress developed in the pipe. Assume that the union at B and couplings at A and C are rigid. Neglect the size of the union. Note: The lead would cause the pipe, when unloaded, to shorten 055 mm when the union is rotated ane revolution. -09m- a6 m.
Determine the support reactions of the depicted system. Neglect the friction of the pulley. B R 2R A - 2R - 3R