Design a 4 bit binary ripple counter that trigger as mention below on the edge of the clock. What will be the count if (a) the normal outputs of the flip‐flops are connected to the clock and that trigger on the positive‐edge of the clock (b) the complement outputs of the flip‐flops are connected to the clock and that trigger on the negative‐edge of the clock

Design a 4 bit binary ripple counter that trigger as mention below on the edge of the clock. What will be the count if (a) the normal outputs of the flip‐flops are connected to the clock and that trigger on the positive‐edge of the clock (b) the complement outputs of the flip‐flops are connected to the clock and that trigger on the negative‐edge of the clock

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

9. Analysis of Synchronous Counters, in the following figure, write the logic equation for each input of each flip-flop. Determine the next state for state 010,011,100,111 as Q2Q1Q0 sequence. FF0 FFI FF2 Ko K, K2 CLK
Draw and explain the operation in detail (while including necessary table) the block diagram and logic circuit diagram of J-K master-slave (M-S) flip flop. Why an M-S configuration is necessary?
Design Master-Slave Flip Flop circuit diagram and write a short description.
4. Design an Octal Counter with D flip-flops. a) Draw the state diagram b) Draw the state table c) Draw the counter circuit
6) For IC 7493, answer the following questions: a) What is the maximum count length of this counter? b) This is a (ripple, synchronous) counter. c) What must be the conditions of the reset inputs for the 7493 to count? d) This is a(an) (down, up) counter. e) The IC 7493 contains (number) flip-flops. f) What is the purpose of the NAND gate in the 7493 counter?
Q: Consider the trailing edge triggered flip-flops shown: a. b. C. PRE D Clock Clock Clock K q' CLR CLR a) Show the timing diagram for Q Clock b) Show a timing diagram for Q if there is no CLR input. i. ii. ii, the CLR input is as shown. Clock R CLR c) Show a timing diagram for Q if i. there is no PRE input. ii. ii. the PRE input is as shown (in addition to the CLR input) Clock CLR PRE
(b) Analyse the sequential logic circuit for the D Flip-Flop shown in Figure below and answer the following sections Determine next state equations. Determine the state table for circuit in section (i). Draw the state machine diagram for D Flip-Flop of circuit in section (i). DD Figure (b)
Design a 2-bit synchronous binary counter using T flip-flops. Include the state diagram, state table, state equation, flip-flop input function and logic diagram
5- a- what are the application of Flip – Flop. b- What is the difference between the Flip – Flop circuit and the other combinational logic circuits?
Task 1: Custom Sequence Counter Using JK Flip Flop, Design a counter circuit that cycles through the sequence: 0, 5, 4, 6, 1, 7, and repeats. Follow these steps: a) State Diagram: Draw a state diagram representing the sequence. Each state should be expressed as a binary number. b) State Table: Create a state table for the counter, detailing current states, next states, and outputs. c) Flip-Flop Input Equations: From the state table, derive the input equations for the flip- flops. Treat any unused states as don't-care conditions. d) Simplification using K-maps: Use Karnaugh maps to simplify the flip-flop input equations. Optionally, verify your simplifications using Multisim. e) Circuit Diagram: Draw the circuit diagram. Task 2: 3-bit Up/Down Counter Using Flip Flop of your choice, design a 3-bit counter that counts up or down based on an input signal X. The counter should behave as follows: Initial State: On powerup, the counter starts at 0. Count Up (X=1): Sequence progresses through…
F4 Using two flip-flops and basic gates, construct the circuit of the given state diagram below. Provide the following: State Table, Flip-flop equations, Circuit Diagram. Follow correct label names: Q0, Q1 – prev/present states D0, D1 – D-FF names X – input Y - output
a) Build a falling edge triggered flip-flop circuit diagram