Electrical EngineeringDesign a low-pass, high-pass, and band-pass filter based on the following schematicselecting your own values for components. Analyse the circuits in frequency iden-tifying center and cut-off frequencies. Build and verify the operation of the circuitbased on the designs.V_L+VC+V_LrefV CrefVR+10.0mH5.0µFVinR15VVout500HZ10.00V Rref

An RLC circuit can be used as Low Pass Filter, High Pass filter as well as Bandpass filter based on…

Design a low-pass, high-pass, and band-pass filter based on the following schema selecting your own values for components. Analyse the circuits in frequency ide tifying center and cut-off frequencies. Build and verify the operation of the circ based on the designs. VL+ VC+ V_Lref C1 V_Cref Lt V_R+ 10.0mH 5.0uF Vin R1 5V 500HZ 2. Vout 10.00 V Rref

Design a low-pass, high-pass, and band-pass filter based on the following schema selecting your own values for components. Analyse the circuits in frequency ide tifying center and cut-off frequencies. Build and verify the operation of the circ based on the designs. VL+ VC+ V_Lref C1 V_Cref Lt V_R+ 10.0mH 5.0uF Vin R1 5V 500HZ 2. Vout 10.00 V Rref

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Design a 3 Band Equalizer based on the following requirements. Use standard component values on your circuit design. The design specification values have a tolerance of +/- 3% of the rated value for cut/boost while a tolerance of+/- 10% of the rated value for frequency values
1. Choose which basic filter response suit the signal output criteria in the figure 2. State your reason. 2. Sketch the basic filter response to suit the output citeria in Figure 2. (with labelling of passband, transition region and cut-off frequency). 3. Choose 1 type of filter if a flat pass-band gain response is required.
(b) Analyse and obtain the transfer function for the filter as shown in Figure Q2(b). R₁ VW HH R₂ W Figure Q2 (b)
Explain why it is necessary to add capacitor in Low pass filter draw circuit diagram and explain w.r.t combination of Capacitor and RL.
A) Write the equation for the small-signal gain function Vout/Vinfor the followingop-amp circuit B) What kind of filter is this circuit? C)Write the equation for the cutoff frequency of the filter D) Sketch the Frequency Response of the system
(b) Analyse and obtain the transfer function for the filter as shown in Figure Q2(b). R2 R1 Vin Vo Figure Q2 (b)
Design an ACTIVE band-pass filter for the midrange part of a loudspeaker so that the bandpass region is 400 Hz-2000 Hz (as defined by the -3dB points). Design the circuit so that the absolute gain is 2. a. Draw the circuit diagram and specify the resistor and capacitor values. Assume you can use either 100, 330, 500, or 1000 Ohm resistors and can select any value of capacitor. b. Sketch the frequency response (Gain [dB] vs. frequency (Hz)). Note that you will need to convert your gain to dB before plotting. Magnitude (dB) 15 10 5 midrange 12 1 -5 -10 -15 -20 -25 10 100 1,000 Frequency (Hz) 10,000 100,000
2. a) Consider the circuit shown in figure 3. i) Determine what type of filter is shown in Figure 3 i) Calculate the corner or cutoff frequency. Take R = 4 k &, L= 2 H, and C= 1 uF. R Figure 3 b) Describe the possibility of building a second order filter with only resistors and capacitors? and design the cutoff frequency of second order filter for low pass filter (Expected: Describe the possibility , design the second order filter for low pass filter circuit and design the cutoff frequency as equation only).
(c) An active filter is shown in Figure Q2(c). RF RA C C R2 Figure Q2(c) Determine the value of C in the circuit if the cut-off frequency is set at 900 Hz and R1 = R2 = 27k 2. (i) (ii) Using the value of C calculated in Q2(c)(i), design the circuit by finding new value for Rị and R2 so that the cut-off frequency is doubled. Draw the frequency response waveform.
What is a bandpass filter? How is its bandwidth defined?
In the circuit below, determine the formula for the cutoff frequency if low-pass or high-pass or center frequency if bandpass/bandstop and determine the transfer function. Also show the type and order of the filter.
3. An essential part of an AC-DC power supply circuit is the filter, used to separate the residual AC (called the "ripple" voltage) from the DC voltage prior to output. Here are two simple AC-DC power supply circuits, one without a filter and one with: Plug unfiltered Plug Filter Vatered Draw the respective output voltage waveforms of these two power supply circuits (unfiltered versus filtered). Explain why that type of filter circuit is needed.