Design a program using the 8085 microprocessor assembly language that performs the following tasks: 1. Initialize register A with a value of OxFF. 2. Load a 16-bit value from memory location 2000H into register pair HL. 3. Subtract the value in register B from the value in register A. 4. Store the result in memory location 3000H. 5. If the result is negative, jump to memory location 4000H.

Design a program using the 8085 microprocessor assembly language that performs the following tasks: 1. Initialize register A with a value of OxFF. 2. Load a 16-bit value from memory location 2000H into register pair HL. 3. Subtract the value in register B from the value in register A. 4. Store the result in memory location 3000H. 5. If the result is negative, jump to memory location 4000H.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

1. Write the contents of all registers and the conditions codes registers after each execution instructions in Table Q1(a). Instructions SUBS r0, rl, 12 MOV 12,13, ASR #3 ro 11223344 Table Q1 (a) rl F7770025 12 r3 CF119856 CF119856 NZ V C 010 1
8085 microprocessor went through its manipulation operation in the ALU, the results was transferred on the data bus and status of the results was stored in the flag register for indications . With your knowledge and understanding illustrate a complete bit configuration of 8085 flag register and show the functions of the represented bits in the register.
- The stack memory is addressed by a combination of the plus offset. The PUSH and POP instructions always transfer between segment -bit number the stack and a register or memory location in the 8086 microprocessors. For string instructions, DI always addresses data in the segment. The 8086 LOOP instruction decrements register for a 0 to decide if a jump occurs and tests it
Draw the figure for memory segments with 8086 microprocessor software model. Explain the logical address structure used for each segment (Explain which registers are used in logical address presentation of each segment; segment address : offset address). Give an example solution to find the physical address in a segment from the logical address for 8086 microprocessor.
Q2. Write assembly language program to substrate two 8-bit numbers and store the result on memory location 3500H. Also show data considered and result of program.
Explain the program memory structure of 8051 microcontroller. Write an ALP using 8085 online simulator tool to perform logical XOR operation for two 8 bit data. Load the accumulator with 34 H and load the B register with 1AH.
Which of the following is incorrect? Select one or more: In AVR, the data memory includes 32 general registers, 64 I/O registers and SRAM. In AVR, both program and SRAM memories have 8-bit data width. The AVR can read both an instruction and data from memory at the same time. The more registers we have for a CPU, the slower processing we can.
Part 2 Study and then differentiate between RAM and ROM memory units in a processor. Describe any possible methods through which you can implement a RAM memory using logic gates.
1- Identify the addressing mode for: MOV Cx, [SI] 2- The instruction that adds immediate datalcontents of memory location specified in an instruction/register to the contents of another register/memory location is a. SUB b. ADD c. MUL Share Content Participants
. Flag Register is a special purpose. Name two types of registers used in 8086 microprocessor. Consider the given example and explain how over flow, carry, parity and auxiallry flag will work on these instruction. MOV AL, 50 (50 is 01010000 which is positive) MOV BL, 32 (32 is 00110010 which is positive) DD AL, BL (82 is 10000010 which is negative)
Suppose we have two registers, Rl and R2, and between them we have a combinational logic circuit. The tpcg = 0.5 ns, tccq = 0.25 ns, tpd = 4 ns, tcd = 2.5 ns, tsetup = 0.5 ns and thold = 0.2 ns. What is the maximum value of fc? Select one: a. 0.2 ps O b. 200 MHz O c. 2 GHz O d. 200 KHz
B) Name the internal registers of 8086, Table the combination of registers to form the physical addresses for memory segments.