Design an FIR linear-phase, digital filter approximating the ideal frequency response TT 1, for |w|≤ 6 TU 0, for <ω <π 6 a) Determine the coefficients of a 25-tap filter based on the window method with a rectangular window. b) Determine and plot the magnitude and phase response of the filter. c) Repeat part (a) and (b) using Hamming window. Ha(w) =

Design an FIR linear-phase, digital filter approximating the ideal frequency response TT 1, for |w|≤ 6 TU 0, for <ω <π 6 a) Determine the coefficients of a 25-tap filter based on the window method with a rectangular window. b) Determine and plot the magnitude and phase response of the filter. c) Repeat part (a) and (b) using Hamming window. Ha(w) =

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

High-frequency ECG analysis in the ST-T segment of an ECG signal recording requires the analysis of signal components above 80 Hz and below 500 Hz. Design a first order band pass passive filter to accommodate this specified frequency bandwidth. Sketch the circuit configuration. You may use an op-amp buffer stage in your circuit design
Design an active high-pass filter circuit using op-amp and calculate the value ofthe capacitor, resistor needed that will produce the cut-off frequency of 331 Hz.
A) Write the equation for the small-signal gain function Vout/Vinfor the followingop-amp circuit B) What kind of filter is this circuit? C)Write the equation for the cutoff frequency of the filter D) Sketch the Frequency Response of the system
Find yzi (n), Yzs (n) and the total solution of the difference equation for the input signal x(n) = 2u(n): y(n) + y(n – 1) – 2y(n - 2) = x(n) y(-1) = 1 y(-2) = -1
What is a notch filter? What is one application?
Briefly -Discuss the effect of increasing the order of the filter on the frequency response of the filter.
Q5: A signal f(t) = 2eatu(-t) is applied to the input of system have frequency transfer function #(w)= %3D Determine the required relations between the Vw +62 constant a andb such that exactly 75% of the input energy on a 1 ohm basis, is transferred to the output.
Design an RLC bandpass passive fiter iparallel LC) if =5 KHz, C-lpF, =1KHz, A) Draw the circuit, laheling the i/p and olp and drive an expression for Ha B) Determine the value of R. L, oa,0a and Q C) Find V. at enaif vat)= 1 sin(ot). D) Sketch (approximately) the gain and phase shift versus en, indicating e, eki, ena E) Determine the new value of if a load of 1000 is applied to the filter and the source has Rin-10 2
Please provide Handwritten answer. Electrical Engineering It is a common practice to low-pass filter signals before feeding them into an A/D Converter. The purpose of this filter is to eliminate any noise or other frequency components beyond a useful frequency range. For instance, if you are recording ECG, you would low-pass filter it at 100Hz because there is no useful frequency components beyond 100Hz and if there is any component that would be noise. What problem arises during sampling of the signal by the A/D Converter if this pre-filter is not used? How does the sampling frequency need to be adjusted with and without the pre-filter? Answer the question considering Nyquist theorem.
6. The response of a band rejected filter is characterized in — — — — —. 4 . c
Problem #1. The parameters for the circuit below are V₁=00, and VBE (on)= 0.7 V. www-H R$ Rc RL STEF RE V+=5 V V = -5 V Low-Frequency Analysis: Clearly draw the small signal low-frequency model (with the Hybrid-) and derive an equation for the break frequency (Hint: Find the Thevenin resistance seen by the capacitor).
1 9) Use harmonic synthesis to construct the complex current given by: i = 10sinwt +4sin2wt amperes.