Design the rod. (Find the diameter d).

Q: 500 N Find the moment 45

A:

Q: Q1) Find the distance of resultant from point(a). 20N -3m 30N 4 30 15N

A:

Q: In Figure 2, solve for the force which will act on the glass window and locate the center of…

A: Given: To find the force and center of pressure.

Q: Construct a rhombus having diagonals of length 60 mm and 75 mm and measure the length of a side.

A: given; lets take diagonal length(p)=60mmlets take diagonal length(q)=75mmside(a)=?

Q: Given the figure determine the bar force at BD and AB

A:

Q: 4- Find fx if fy is 1KHZ and number or horizontal tangencies is 2 and the vertical is 3.

A:

Q: In a crossed-belt drive, two sheaves have diameters of 10 in and 12in. If the center distance is…

A: Given data, Centre  distance, x= 14 in.  d1= 10 in. d2= 12 in. It is cross belt.

Q: 3. In the figure shown, solve for the distance b. 36 kN 20 kN y 94 kN m 2 m 3 m 2 m

A: Given Data :

Q: PO 8 in.

A: Redraw the following figure for the given question.

Q: find B 20 ft 75° 10 ft magnitude of force F and the angle at point B ?

A: According to Lamis Theorem, whenever at a point three forces are acting then the ratio of force upon…

Q: find the total force ov

A:

Q: (twisting moment x shaft length) If X = Angle of twist per unit length of the shaft then the unit of…

A: The angle of twist: the angle at which the fixed end of the shaft rotates with respect to the free…

Q: The post weighing 1500 lbs is to just be vertically pulled out of the ground using two ropes as…

A:

Q: iven: W =  656 lb

A: w=656lb to find tension in cable

Q: Determine the angle 0 if the

A: GIven: FA=600 N V=20 m/s D=50 mm=0.05 m To determine: The angle theta

Q: 2.1. Compute the resultant reaction at A. (CONSIDER 2-DECIMAL PLACES; NO NEED TO WRITE THE UNIT)

A:

Q: the shear force right of C is

A:

Q: Solve for the mobility.

A:

Q: of F about axis BA. Express the resu f the curved sections are all 0.5 m.

A:

Q: 2-5. A horizontal shaft exerts a sideways thrust of 200 N to the right and a downward load of 600 N…

A: Resultant is simply the square root of sideway thrust square and downward load square, putting given…

Q: If the diameter (d) of wheel is reduced in half times in size, Then the torque produced in the wheel…

A: If the diameter (d) of wheel is reduced to half times in size, Then the torque produced in the wheel…

Q: 8 kN/m Refer to figure 19, Calculate the magnitude and 4 kN/m position of the resultant load from…

A: Draw the free-body diagram of the beam.

Q: In the previous question, the bending moment at a distance 25 in. Is -lb.in.

A: Given Distance = 25 in To find Bending moment

Q: 3-9. Solve for the algebraic sum of the moments in pound-feet about A when h is 20 m as shown in…

A: Given data h = 20m Forces acting are 800N, 500N

Q: FIND THE FORCES IN JOINT A

A:

Q: Resolve the 500-lb of fig. into two components: a shearing component parallel to AB and a normal…

A: In this question, force 500lb is to be resolved along two mutually perpendicular lines, one is…

Q: 500 kN.m T KN. m/ m В C 2 m 3 m 5 m Q/Find the value of T (kN. m/m) So that the value of angle of…

A: Given Data Angle of twist at D is zero At A is fixed support so the angle of twist at A is zero…

Q: 3.

A: Degree of Freedom (mobility): The minimum number of independent variables required to define the…

Q: 3) A right circular cone of 30 mm diameter and 60 mm height is cut from a cylinder of 50 mm diameter…

A:

Q: y, determine the required diameter of the rod.

A:

Q: Given the 600-N force applied to the bracket at A in Fig 1, determine:

A: Given Data: The force acting at point A is F = 600 N. The angle made by F with the east direction…

Q: R mm 150 mm א

A:

Q: Figure of Q4 b (m) 450 b (m)

A: As per given question The slider block C moves at 10 m/s down the inclined groove. Both links have…

Q: 3 Find the force on the bottom of the cylinder of: 5 ad/s 10 rad/s (b) 7 rad/s (d) 20 rad/s

A:

Q: . Find the width of the belt used it

A: To find width of belt (b)

Q: For the given figure shown, a - 6 m, b = 9 m, c= 3 m, r= 7m. h b

A: The centroid of arc of a circle is on the X -axis So centroid of arc of circle wrt to X-axis is; Y1…

Q: Find the angles between the force F = 1200i + 800j − 1500k N and the x-, y-, and z-axes.

A:

Q: Draw the free-body diagram of the following shapes

A: Consider the free body diagram shown below for the first diagram.

Q: Determine the flange thickness if the

A: To find Flange thickness

Q: Find the value of P and the distance x so that the bar AB remains horizontal. Take the radius of the…

A: The 2000 N weight acting on the left rod. The force P and the distance x from A needs to be…

Q: Find the tensian focce in each cable.

A:

Q: Find the allowable maximum value of F.

A: we have to evaluate the maximum bending stress

Q: Q5/ Find the equation tor the plane P(0,2,-1) and nomal to thiough n= 3i-25 -k

A:

Q: Fsc RA 60 B

A: Given data⇒

Q: For the following Internal clovetails if b is yomm grater than C. M is 60 mm 25 mm less Find the…

A:

Q: Compute  (I bar sub x, in mm4, round-off to 2 decimal places) for the region sh

A:

Q: Find the resultant R of the force System Shown in 40 figure. Show it's position with-respect- to…

A: TO FIND: The resultant R of the force system: Also the position with respect to the point C

Q: Q3: A' am with cross section shown in the following image, find out the principle аxes. 100mm L.…

A: Let's divide the given cross section into two parts Part (1): A rectangle of length 100 mm and…

Fluid Kinematics

The branch of science that deals with objects which are either in motion or stationary are studied under the branch of classical mechanics. Fluid mechanics is a subcategory of classical mechanics that deals with the behavior of fluids at rest (fluid statics) or in motion (posing some velocity). In fluid kinematics, studies focus on the associated motion of fluid particles or groups of particles, and its associated parameters like displacements, velocity, and acceleration without concerning about the forces that caused the motion. All the laws of classical mechanics are applied in the study of fluid kinematics.