Q.2) A 900 kg mass is hanging from the pulley of a frame as shown below.Determine:(a) the support reactions at A and C.(b)the force acting on member AB at pin B.OB2 m3 m0.6 m0.5 m

Answered: Image /qna-images/answer/aa4f20ce-f508-41f5-a0e5-3b454b790ad8.jpg

Answered: Determine: (a) the support reactions at…

Engineering

Mechanical Engineering

Determine: (a) the support reactions at A and C. (b) the force acting on member AB at pin B. 0.5 m B 2 m A 3 m 0.6 m

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter5: Three-dimensional Equilibrium

Section: Chapter Questions

Problem 5.50RP: The 180-lb homogeneous bar is supported by a ball-and-socket joint at A and two cables attached to...

See similar textbooks

Related questions

Q: The gearing of a machine tool is shown in the Figure below. The motor shaft is connected to gear 1…

A: The speed of gear 1, N1=1200 rpmThe number of teeth on gear 1, T1=40The number of teeth on gear 2,…

Q: * In adiabatic process, the system has Q=max. value O W=0 O U=0 O O Q = 0

A: To find : In adiabatic process, the system which of the following

Q: The 3D model can be reflected about OXY plane OXY, YZ and XZ planes O YZ plane XY and XZ planes O…

A: Reflection of object is like mirror of an object. Reflection transformation matrix is used to do the…

Q: The elements of boundary model for box with through hole are OV= 10, E= 15, F= 9, H= 2, G= 1 and C=…

A: Write the given data from the given options. No. of vertices, V=10No. of Edges, E=15H=2No. of holes,…

Q: 8-1 A power screw is 25 mm in diameter and has a thread pitch of 5 mm. (a) Find the thread depth,…

Q: A rope with two mass-less platforms at its two ends passes over a fixed pulley as shown in the…

Q: The center O of the disk has the velocity and acceleration shown in the figure. If the disk rolls…

Q: It is recommended that the overall heat transfer factor (U) be: a. Small b. More than 1 a c. It does…

Q: Explain in detail about Vehicle Aerodynamics

A: The study of air flows around and through the vehicle body is known as Vehicle aerodynamics. Because…

Q: REAL-WORLD APPLICATION, of Entropy of mixing in Idea Gases

Q: 6/51 The 10° doorstop is inserted with a rightward hori- zontal force of 30 lb. If the coefficient…

Q: A system subject to sinusoidal excitation is shown in the Figure below: m X, X, X and is modelled as…

A: Given: Natural frequency of the vibration: →ωn=11 rad/s And damping ratio: →ζ=0 Maximum excitation…

Q: Problem 2 The are studying a planetary gear system. The outer gear ring is stationary. A motor that…

Q: 05: For the given state of stresses shown, draw the required Mohr's circle and determine: The…

Q: 1. A horizontal "hot air blower" consists of a fan, an electrical heating element and a nozzle The…

A: “Since you have posted a question with multiple subparts, we will solve first three sub parts for…

Q: The three-dimensional models can be rotated about O z-axis only Ox-axis, y-axis and z-axis Ox-axis…

Q: 3. The sealar triple product for A=(5,-1.1), B=(-2,0,4), C = (3,4,5) is A. -74 B. -66 C. -110 D. -86…

A: Given:A=(5,-1,1)B=(-2,0,4)C=(3,4,5)

Q: In tensile test a plain carbon steel specimen has a (40mm) gauge length and the Final area (A final)…

Q: 5. For the overdamped oscillations, the displacement x(t) is expressed by the following x(t)-e-[A et…

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ =…

Q: The machine shown in the figure can be used for a tension test but not for a compression test. Why?…

A: Given: There are three gears connected in series and the middle gear is attached to the motor. And…

Q: Consider a steam power plant operating on the ideal regenerative Rankine cycle with one open…

A: Given: Let us consider the given, P1=10 kPaP2=P3=1.2 MPaP4=P5=15 MPaTs=600°C To find: The amount of…

Q: Q3: For the stresses at the point shown, find the followings: 1- The maximum shear stress. 2- The…

Q: A Steam at 400 deg C and 8,200 kilo Pascals enters a turbine and leaves at 10 kPa. What is the…

Q: 2. A refrigerated cold room wall has a thickness of 100mm and a thermal conductivity 0.14 W/m-K. The…

Q: Cable AB passes over the small ideal pulley C without a change in its tension. What length of cable…

Q: In adiabatic process, the system has Q=max. value O W=0 O U=0 O Q = 0 O

A: in adiabatic process work not zero so answer of 2nd option was wrong and internal energy also there…

Q: Consider a silicon wafer positioned in a furnace that is zone-heated on the top section and cooled…

A: Solution.jpg

Q: Air flows through a constant cross-section conduit with Mack number Ma = 1 at 200 KPa pressure and…

A: given; mach number(Ma)=1initial pressure(P)=200KPainitial temperature(T1)=1000c(a)stagnation…

Q: 11. A particle is released from the rest (y=0) and falls under the influence of gravity with air…

Q: 3 E=20000MPa I=1.61x10^6 sqmm Analyze the structure using Consistent Deformation Method. Draw Shear…

Q: The 60-lb block A is placed on top of two nested springs B and C and then pushed down to the…

A: The weight of the block A, W=60 lbStiffness of spring B, kB=200 lb/inStiffnes of spring C, kC=100…

Q: The solid circular rod has a cross-sectional area of 420 mm². It is subjected to a uniform axial…

Q: HW10 Two parallel shafts are to be connected by spur gearing. The approximate distance between the…

Q: The known mean velocity is 15.6 mph at a site at a height of 31 ft (about 10m). Approximate the wind…

A: Given data: H1 = 31 ft V1 = 15.6 mph H2 = 100 ft p = 0.3 To find: V2 = ?

Q: Hypothetical metal has an FCC crystal structure. If its density is 22.4 g/cm3, and atomic weight is…

Q: A uniform disc of a 90 mm radius has a mass of 2500 g. It is mounted centrally in bearings that…

Q: HW8 The arms of a Porter governor are 310 mm long. The upper arms are pivoted on the axis of…

Q: 5. When water freezes, it expands by about 9.00%. What pressure increase would occur inside your…

A: GIVEN DATA: Let, v = initial volume When water freezes change in volume, dv = 0.09 v Volumetric…

Q: What is the result of: | 4ai (2ai + 3j) | ...i and j are unit vectors.

Q: A shaft of diameter 250.04 mm is assembled in a hole of diameter 25-0.02 mm. Match the allowance and…

Q: Two 6-in.-wide wooden boards are to be joined by splice plates that will be fully glued on the…

Q: in the compression stroke of a gas engine the work done on the gas by the piston is 70 kJ/kg and the…

Q: A stainless steel tube with an outside diameter of 60 mm and a wall thickness of 5 mm is used as a…

Q: Hypothetical metal has an FCC crystal structure. If its density is 22.4 g/cm3, and atomic weight is…

Q: The cost of producing a small radio set consists of Php 23.00 labor and Php 37.00 for materials.…

Q: for the Plane frameshown in Figure determine the axial force in cord (DE) and the horizontal and…

A: To find: Tension in cable DE. Reaction forces at A.

Q: Consider a silicon wafer positioned in a furnace that is zone-heated on the top section and cooled…

A: Given data: Tsur,h=1200 KTsur,c=330 Kε=0.65d=0.78T∞=700 KhT=8 W/m2.Khb=4 W/m2.K Need to determine…

Q: A propeller shaft in a ship is 350mm in diameter and 5.25 m in length. The allowable shearing stress…

Q: A flanged bolt coupling consist of six 10 mm diameter steel bolts on a bolt circle 300 mm. in…

Question

Q.2) A 900 kg mass is hanging from the pulley of a frame as shown below.
Determine:
(a) the support reactions at A and C.
(b)
the force acting on member AB at pin B.
O
B
2 m
3 m
0.6 m
0.5 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The 180-lb homogeneous bar is supported by a ball-and-socket joint at A and two cables attached to B. Determine the forces in the cables.
Two concrete blocks weighing 320 lb each form part of the retaining wall of a swimming pool. Will the blocks be in equilibrium when the pool is filled and the water exerts the line loading shown?
Q.2) A structure system shown below supports a mass of 450 Kg. Determine the support reactions at A and B. Neglect the weights of the pulley and the bars. Note: the radius of pulley D is 175 mm. A C 600 mm 600 mm 175 mm
Member AB is supported by a roller at A and a pin at B. Draw the FBD and determine the reaction forces at A and B. 390 lb (1) Draw FBD 13 12 (2) Determine reaction forces 800 Ib ft A 390eb 30peb-ft Bra +4ft- -4 ft- 8 ft- 3 ft 30% Br B 9ft 34+ BY B
1. A rectangular plate 20-kg is supported by three cables as shown. Determine: 1.1 Drawing Free-Body-Diagram (FBD) 1.2 Tension in each cable. y Unit: m 4.8 3.0 D B 5.0 1.3 3.2 3.6 X 4.5 C z
Q2: - The weight W= 10 kN hangs from the cable, which passes over the pulley at F. Neglecting the weights of the bars and the pulley, determine the magnitude of the pin reaction at D and and all forces acting on member ABC. 15 m PD 1.5 m R=0.4 m 2 m 2 m
1. Solve the components of the reaction at pin C and the tension at rod AB. 8 in -3 in2 in. 5 kip 3 kip (a)
Q.3) A cylinder weighing 600 N is supported by a pin-connected two-bar frame. Determine the forces exerted on the cylinder by the contacting surfaces. Also, find the reactions at support A and C. 0.2 m 4 0.3 m B 3 0.2 m C 0.4 m 0.4 m
4. A cylinder weighing 400lb is held against a smooth incline by means of of a weightless rod AB. Determine the forces P and N exerted on the cylinder by the rod and the incdine. W=400b.
The bars ACE and BCD are supported by a pin and slot arrangement at C. ACE is supported by a pin at A, and bar BCD is fixed to the ground at B. а. Draw a FBD of the bar ACE. Determine all support reactions at A, and determine the slot reaction at C. b. Draw a FBD of bar BCD, and determine all the support reactions at B. lolb D ft M = 150 lbft Vイ = Soeb 3 ft W=20lb ft 3 ft B 4 ft 4 ft
The frame shown supports part of the roof of a small building. Knowing that the tension in the cable is 200 KN, determine the resultant of reactions at the hinge support F. A B 2.25 m C 3.75 m 20 kN 20 kN 20 KN 20 kN 1.8 m'1.8 m'1.8 m'1.8 mE -4.5 m Hibbeler, 2008. Select one: a. 150 KN b. 180 KN c. 200 KN O d. 100 KN
Q2: The structure shown in the diagram ( one ofthe two identical structures that support the scoop of the excavator) suports a downward force 1800 N at G. Determine reactions on member CDK. 320 mm Shaft -Scoop B 260 mm 100 mm 180 mm 260 mm F 160 mm |K 380 mm 1040 200 mm mm 1120 mm