Determine the centre of pressure on an isosceles triangle plate of base 9m and altitude 6m when it is immersed vertically in an oil of specific gravity 0.57. The base of the plate coincides with the free surface of oil.

Determine the centre of pressure on an isosceles triangle plate of base 9m and altitude 6m when it is immersed vertically in an oil of specific gravity 0.57. The base of the plate coincides with the free surface of oil.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: B DB z (vertical) L DA

A: Solution:-

Q: H.W.10// Is the gauge pressure at the center of the pipe (a) negative, (b) zero, or (c) positive?…

A: Given data: h1=6 in. h2=12 in. h3=30 in. S.G1 =1 S.G2=2

Q: Determine the center of pressure (in meters) of an isosceles triangular plate of base 5m and…

A: To determine the center of pressure. Given, Base of the triangular gate = 5 m Altitude of the…

Q: 3) Water from a reservoir is raised in a vertical tube of internal diameter D= 30 cm under the…

Q: A closed cylindrical tank 2m in diameter and 7m high has 3m tall of water and 3m of oil (SG = 0.8).…

Q: Total vertical pressure at any plane is equal to a) o = o + u b) o = 0 + u c)o = o' +v %3D d) None…

A: Pore water pressure=u Total stress=σ Effective stress=σ' σ=σ'+u

Q: A reducing elbow is used to deflect water flow at a rate of 14 kg/s in a horizontal pipe upward 30°…

A: Given data:m=14 kg/s˙A1=113 cm2A2=7 cm2h=30 cm

Q: A 1.35 meter high cylindrical tank is used in lifting oil to the top of the building. The allowable…

A: Height (h) = 1.35m Pressure (P) = 16kPa = 16000N/m2 taking density of water as 1000kg/m3 It has…

Q: A vertical rectangular gate 1.6 m wide and 5.6 m high is submerged in oil (SG=0.91) with its bottom…

Q: A vertical triangular plane area, submerged in water, with one side in the free surface, vertex…

A: Solution : vertical triangle submerged in water with one on side on free surface pressure center…

Q: PROBLEM 38: A 3-m square plane metal surface is to be placed vertically below the water surface. The…

Q: The container is partially filled with oil, water, and air. Take ??=62.4 ??/??3, ??=58.4 ??/??3,…

A: Using hydrostatic law pressure can be calculated at this point. Which states that rate of increase…

Q: What is the pressure at the bottom of the disk? Unit weight of water is 9.79 kN/m³. 3m 0.6

Q: A reducing elbow is used to deflect water flow at a rate of 14 kg/s in a horizontal pipe upward 30°…

A: given data:- mass rate of flow=14kg/s inlet area=113cm2 outlet area=7cm2 head difference=30 cm

Q: Determine the depth of center of pressure on a plane rectangular surface of 1 m wide and 3 m deep…

Q: An open cylindrical tank has a base diameter of 1.2 meters and contains 3.86 meters deep of water.…

Q: A closed cylindrical tank 1.89m high and 0.99m in diameter contains water of height 1.35m. When the…

A: We know that y=ω2r22gy=2020.992229.81y=4.9954my'=4.9954m-1.35m=3.6454m

Q: A triangle having a base of 1.20m and altitude of 1.8m wholly immersed in water, its base being in…

A: Given: b = 1.2m, h = 1.8m

Q: A closed rectangular tank 1.20m high by 2.40m long by 1.50m wide is filled with water and the…

Q: An open cylindrical tank 30 cm. in diam. änd 80 cm, high partially filled with water is rotated…

Q: 8. Determine the centre of pressure on an isosceles triangle plate of base 6m and altitude 6m when…

A: The study of fluid behaviour (liquids, gases, blood, and plasmas) at rest and in motion is known as…

Q: Find the pressure at depth of 2.556 m from top of water. Take density of water as 1000 kg/m3

Q: A closed cylindrical tank 2m in diameter and 7m high has 3m tall of water and 3m of oil (SG = 0.8).…

A: To determine the theoretical velocity and and the horizontal distance where the jet strikes the…

Q: A triangular gate with a base width of 2 m and a height of 1.5 m lies in a vertical plane. The top…

Q: 4-51. Calculate the net hydrostatic pressure force on curved surface AB of the open tank of Figure…

Q: If DA = 22cm, DB = 5cm and L = 9m, and if oil is flowing at a rate of 0.01 m³/ s, determine the…

Q: An open tank containing water is accelerated vertically at 6.28 . If s2 the motion is downward with…

A: Assuming the atmospheric pressure to be equal to ZERO gage value. The change in pressure will…

Q: A 2.8m square plate is completely immersed under water in a vertical position such that the two…

Q: The coefficient of active pressure for an angle of internal friction of 28.4° is: Round off to three…

Q: shown is filled with oil. Determine the pressure heads

A: Given data - SG of oil = 0.85 Density of oil = S.G × 1000kg /m³ Density of oil = 0.85 ×1000kg/m³=…

Q: A vertical cylindrical tank has a diameter of 1 meter and is 2 meters high. It is closed at the top…

Q: A square frame 5 m by 5 m in dimension is submerged in water vertically with its top of 3 meters…

A: We need to find out pressure at different locations given

Q: A triangle having a base of 1.20m and altitude of 1.8m wholly immersed in water, its base being in…

A: Length of base of triangle = 1.2m altitude of triangle = 1.8m It has been asked in the question to…

Q: If a triangle of height d and base a is vertical and submerged in liquid with its vertex a distance…

A: The center of pressure is the point where the total sum of a pressure field acts on a body, causing…

Q: 8. For an inclined plane for which position, maximum total pressure acts on it. a) Horizontal b)…

Q: An open tank containing water is accelerated vertically at 5.01 If the motion is downward with…

Q: . A rectangular tank 2m long, 1.5m wide and 1.5m deep is filled with oil of specific gravity 0.8.…

Q: What is the pressure at the bottom of the disk? Unit weight of water is 9.79 kN/m³. W.S. 3m 0.6- Im

A: We have to determine the value of pressure at the bottom of the disk according to the given data.

Q: 3.) Determine the total pressure and center of pressure on a circular plate of diameter 3700mm which…

A: The pressure force on a submerged body is equal to product of pressure at centroid and area of body.…

Q: A vertical triangular plane area, submerged in water, with one side in the free surface, vertex…

A: To determine the location of center of pressure of a inverted triangular plane area from the free…

Q: A square plate having one of its side equal to 3m is immerse in a water surface in a vertical…

A: The average pressure on the square plate is…

Q: A closed cylindrical tank 1.845m high and 0.945m in diameter contains water of height 1.35m. When…

Q: 1) A 3-m square plate is immersed in water in a vertical position such that the two edges of the…

Q: 3. A square disc of 1 m side is immersed vertically in water as shown in the figure. If the highest…

A: Note : The figure is not mentioned in the question. It is necessary to mention figure when it is…

Q: A square plate having one of its side equal to 3m is immerse in a water surface in a vertical…

A: Distance of center of pressure can be calculated by hp=IAy+yy=diatance of center of gravity from…

Q: A gate 1.60 m wide and 2 m high has water on one side and is inclined 45° with the horizontal. Water…

A: Given data: Width of gate=1.6 m Height of gate=2m Inclination=45 degrees Water depth=1.5 m It is…

Q: A closed cylindrical tank 2m in diameter and 7m high has 3m tall of water and 3m of oil (SG = 0.8).…

Q: Determine the horizontal component of the total hydrostatic force (kN) the oil exerts on the face AB…

Q: Determine the depth of center of pressure on a plane rectangular surface of 1 m wide and 3 m deep…

Concept explainers

Beams and Frames

A beam is a horizontal structure or a member which is always subjected to transverse shear loads.

Question

Choose the correct answer

d) 4 m

a) 6 m

c) 9 m

b) 3 m

e) None of the mentioned

Determine the centre of pressure on an isosceles triangle plate of
base 9m and altitude 6m when it is immersed vertically in an oil of
specific gravity 0.57. The base of the plate coincides with the free
surface of oil.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2 solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine TP and CP on a triangular plate of base 5 m and altitude 5 m, when it immersed vertically in an oil of S = 0.8. The base of the plate coincides with the oil surface.
An isosceles triangular plate of base 3 m and altitude 3 m is immersed vertically in an oil of specific gravity 0.8. The base of the plate coincides with the free surface of oil. The centre of pressure will lie at a distance of (from free surface)
Find the (i) slope of the liquid surface, (ii) Pressure at B, for the liquid contain subjected to acceleration of 5 m/s? on a ramp of inclination 30° to the horizontal as shown in figure. 3 m 5 m/sec? 2m p= (0.8p)- %3D L. A 30
A triangular plate of 1 m base and 1.5 m altitude is immersed in water. The plane of the plate is inclined at 30° with water surface while the base is parallel to and at a depth of 2 m from the water surface. Calculate the position of the center of pressure in meters. a.2.987 b.1.896 c.3.234 d.2.264
A 2.8m square plate is completely immersed under water in a vertical position such that the two edges of the square are horizontal. It is immersed such that the center of pressure is located 8cm below its center of gravity. Determine the distance of the bottom of the plate from the water surface. O 10.6m O 9.6m O 9.1m O 10.1m
A square plate having one of its side equal to 3m is immerse in a water surface in a vertical position such that the two edges of the square would be horizontal in order that the center of pressure shall be 10 cm from the center of gravity. a) How far below the water surface should the upper plate be submerged? b.) What is the distance of the center of pressure from the water surface. c) Retermine the total hydrostatic force acting on the plate at this postion.
2. An oil is flowing between two parallel horizontal plates which are 20 mm apart. The top plate is moving with a uniform speed 0.1 m/s. The viscosity of the oil is 0.1 N.s/m². The velocity at the centerline is 1.95 m/s. Consider the flow to be a fully developed one. a) Derive the velocity profile b) Calculate pressure difference between two points (Pi-P2) 5 m apart c) Find the velocity at 3 mm from the wall of the bottom plates. d) Find the velocity at 3 mm from the wall of the top plates. e) Determine force acting on the bottom wall, (W=10 cm) 0.1 m/s Oil P1 P2 2 cm y 5 m
1. A square plate having one of its side equal to 3m is immerse in a water surface in a vertical position such that the two edges of the square would be horizontal in order that the center of pressure shall be 8cm. from the center of gravity. a. How far below the water surface should the upper plate be submerged? b. What is the distance of the center of pressure from the water surface? c. Determine the hydrostatic force acting on the plate at this position. 2. A dam is triangular in aross section with the upstream vertical. The water surface elevation is also at the top of the dam. The dam is 8m high and 6m wide at the bottom. The coefficient of friction between the base and the foundation is 0.80. Hydrostatic uplift varies from full at the heel to zero at the toe. (= 23.5 kN/m³) a. Determine the factor of safety against overturning. b. Determine the factor of safety against sliding. c. Determine the stress at toe.
... 60КРа 93КРа Water 15cm 15cm Mercury YSG = 13.6) %3D Figure B Figure A The pressure at point 1 in Figure A is 60KPA. Afterwards, the pressure at point 1 is increased and the new pressure now is 93KPA as shown in Figure B. Due to the increased in pressure, the manometer moves along the manometer by 15cm as shown. The angle of inclination is e = Blank 1 degrees. Blank 1 Add your answer
A 2.8m square plate is completely immersed under water in a vertical position such that the two edges of the square are horizontal. It is immersed such that the center of pressure is located 8cm below its center of gravity. Determine the distance of the top of the plate from the water surface. O 6.8m O 6.3m O 7.3m O 7.8m
Q1 Determine the total pressure and center of pressure on an isosceles triangular plate of base 4m and altitude 4m when it is immersed vertically in oil of sp. gr. 0.9. The base of the plate coincides with the free surface of the oil. FREE OIL SURFACE than -4m- GP 4 m
An oil is flowing between two parallel horizontal plates which are 20 mm apart. The top plate is moving witha uniform speed 0.1 m/s. The viscosity of the oil is 0.1 N s/m2. The velocity at the centerline is 1.95 m/s.Consider the flow to be a fully developed one.a) Derive the velocity profileb) Calculate pressure difference between two points (P1-P2) 5 m apartc) Find the velocity at 3 mm from the wall of the bottom plates.d) Find the velocity at 3 mm from the wall of the top plates.e) Determine force acting on the bottom wall, (W=10 cm)