Determine the following of the parallel tuned circuit as shown in Figure 2 at a frequency of 500 kHz and for a bandwidth of operation equal to 20 kHz. The resistance of the coil is 5 ohms. Figure 2 (a) The value of the inductor in uH. (b) The value of the capacitor in nF. (c) The impedance of the circuit in kQ. r000

Determine the following of the parallel tuned circuit as shown in Figure 2 at a frequency of 500 kHz and for a bandwidth of operation equal to 20 kHz. The resistance of the coil is 5 ohms. Figure 2 (a) The value of the inductor in uH. (b) The value of the capacitor in nF. (c) The impedance of the circuit in kQ. r000

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 6RQ: A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating...

See similar textbooks

Similar questions

1- In a buck DC/DC converter: ton Va = 100 V, R = 80, D ==0.8, f == 20000 Hz, L = 200 μH, Find: a) average voltage and current of the load Vala. b) maximum and minimum current of inductor. c) Voltage ripple of the capacitor. d) the average input current. e) draw the figure of the inductor current. C1 = 40 Micro farad Q Vd - İd K C1 ww + Vo
Answer the following with illustration and solution. 1.) A circuit consisting of a resistor of 5kohms in series with a capacitor of 10 nanofarad is connected across a 16v sinusoidal supply. Calculate the output voltage at a frequency of 60Hz and again at frequency of 120Hz. This is the example/guide that might help.
C5 What is the correct explanation for the voltage seen at Va in Figure C5? Va 1 Sost We will assume that the Vout Out Vb, capacitor is charged to a value determined by the feedback and the supply voltage +BVsat. Figure C5 A. The waveform on the capacitor looks like a discharge, and then a charging waveform to an equal but opposite magnitude voltage, B. The capacitor simply reverses its charge, with a charging waveform, C. The capacitor simply reverses its charge, with a discharging waveform, D. None of the above.
A step down converter is operated with a duty cycle of k = 0.75. The input voltage is Vs = 20V, and the load is: L = 5mH, R = 1502. The minimum inductor current is I₁ = 0.1A. The maximum inductor current is: Select one: a. 1.9 A b. None of these OC. 0.9 A O d. 1.1 A Oe. 2 A
Boost Converter Design A boost converter is required to have an output voltage of 8 V and supply a load current of 1 A. The input voltage varies from 2.7 to 4.2 V. A control circuit adjusts the duty ratio to keep the output voltage constant. Select the switching frequency. Determine a value for the inductor such that the variation in inductor current is no more than 40 percent of the average inductor current for all operating conditions. Determine a value of an ideal capacitor such that the output voltage ripple is no more than 2 percent. Determine the maximum capacitor equivalent series resistance for a 2 percent ripple.
C'uk Converter Design A C'uk converter has an input of 12 V and is to have an output of - 24 V supplying a 60 W load. Select the duty ratio, the switching frequency, the inductor sizes such that the change in inductor currents is no more than 12 percent of the average inductor current, the output ripple voltage is no more than 1.5 percent, and the ripple voltage across C1 is no more than 3 percent.
1- In a buck DC/DC converter: ton V₁ = 100 V, R= 80, D ==0.8, f == 20000 Hz, L = 200 μH, Find: a) average voltage and current of the load Vala. b) maximum and minimum current of inductor. c) Voltage ripple of the capacitor. d) the average input current. e) draw the figure of the inductor current. C1 = 40 Micro farad Q Vd - İd K C1 ww + Vo
R +Vcc -Vcc C Vout R R a. Quantify how the resistors and the capacitor influence the output voltage of the circuit, Vout. What are the upper and lower limits of Vc? b. Howlong does it take for the capacitor to be charged from minimum to maximum voltage and vice versa?
Buck Converter Design Power supplies for telecommunications applications may require high currents at low voltages. Design a buck converter that has an input voltage of 3.3 V and an output voltageof 1.2 V. The output current varies between 4 and 6 A. The output voltage ripple mustnot exceed 2 percent. Specify the inductor value such that the peak-to-peak variation in inductor current does not exceed 40 percent of the average value. Determine the required rms current rating of the inductor and of the capacitor. Determine the maximum equivalentseries resistance of the capacitor.
A resistor & a capacitor are connected in series across 230V, ac supply. The current taken by the circuit is 4 A for 50 Hz frequency. The current is reduced to 2 A, when the frequency of supply is decreased to 40 Hz. Determine the value of resistor & the capacitor.
SIGNAL Mention the function or work of each component in the circuit? + Vcc Rc Rc Cc HH www R₁ Cin HH R₂ www. RE Cc HH CE www R₁ 30 www wwww RE CE OUTPUT
Q/ Design a circuit to limit a 20 V rms sinusoidal voltage to a maximum positive amplitude of 10 V and a maximum negative amplitude of -5 V using a single 14 V dc voltage sour.