During the manufacturing of a wire of 6 mm in diameter, a metallic material with mechanical properties such as K = 1100 MPa and n 0.3 was used. If the initial %3D !3! diameter of the rod was 11 mm, and the speed used was 0.6 m/s, and, assuming that the frictional and redundant work together constitute 30% of the ideal work of deformation, a)- Calculate the power required to perform this operation b)- Calculate the die pressure at the die exit.

During the manufacturing of a wire of 6 mm in diameter, a metallic material with mechanical properties such as K = 1100 MPa and n 0.3 was used. If the initial %3D !3! diameter of the rod was 11 mm, and the speed used was 0.6 m/s, and, assuming that the frictional and redundant work together constitute 30% of the ideal work of deformation, a)- Calculate the power required to perform this operation b)- Calculate the die pressure at the die exit.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1) Drawing: Consider a cylindrical rod fabricated from a linear strain hardening material with a constitutive relationship of o=2000 + 20000 € (where o is in psi). The rod is drawn into a wire. If the original diameter of the rod is 0.75 in, what is the minimum possible diameter that can be drawn in the first pass? Assume that redundant work is 20% of the ideal work and that the frictional work is 15% of the ideal work of deformation. What is the drawing force required to complete this operation?
2) Drawing: A round rod of annealed 302 stainless steel (K = 1300 MPa and n = 0.3) is being drawn from a diameter of 15 mm to a diameter of 12 mm at a speed 0.25 m/s, using a semidie angle of 8º. a. Calculate the percentage reduction, the applied force due to ideal deformation, friction, and inhomogeneous deformation. Assume coefficient of friction of 0.1. b. Calculate the required power, process efficiency, and the die pressure at the exit.
5 UEME1233 MANUFACTURING TECHNOLOGY I (а) 25 mm on a layered structure of natural fibre-reinforced polymer composite. He encountered delamination problem in the workpiece (Figure 3) when he used conventional cutting tool to drill the hole. Instead of using conventional machining process, discuss ONE suitable advanced machining process that can be applied for this machining purpose and predict TWO possible limitations for the selected process. Q3. An engineer would like to drill a square hole of 20 mm x 20 mm with depth of (Word limit: ~100) Cutting Tool Delamination – Composite Material Figure 3. Delamination of the composite material. A resistance welding is performed to join two 2-mm thick stainless steel sheets (b) with ten 6-mm diameter spot welds produced concurrently. The resulted weld nugget each has average 3 mm in thickness. Calculate the required welding current and energy consumption for the welding if ten seconds are needed for the whole welding operation. Given that the…
3) Forging: A cylindrical specimen made of annealed 4135 steel (K = 1015 MPa, n = 0.17) has a diameter of 150 mm, and is 100 mm high. It is upset between dies to a height of 50 mm at room temperature. Calculate the work done for 2 cases: a) Ideal (frictionless) b) Friction, where the coefficient of friction is 0.2. Set up on paper and solve using software. Be careful with units.
The temperature distribution at a certain input of time in concrete slab during curing is given by T= 3+3r + 16 where x is in cm and T is in K. The rate of change of temperature with time is given (a = 0.003 cm2/s). (a) 0.009 K/s (b) 0.0048 K/s (c) -0.0012 K/s (d) -0.0018 K/s
A compression test is performed on a 2” diameter by 5” long bar of an unknown metal. At the end of the compression test, the bar has a height of 3.5 inches. The strength coefficient (K) and the work hardening coefficient (n ) are 250 MPa and 0.4, respectively. State all assumptions needed to work the problem. a) Calculate the final diameter of the bar in inches. b) Calculate the flow stress in MPa when the length of the bar is 4”.
7. A strip of annealed low-carbon steel (K = 528 MPa, n = 0.25) is rolled from its initial dimensions (210 mm wide and 13 mm thick) to a thickness of 7 mm. The rollers have a radius of 250 mm, the roller rotates at 200 rpm, and u = 0.1. Compare this high frictional force and power with the low frictional (u = 0) forces and power. a. Estimate the roll force and power required for this process.
A cylindrical workpiece of 100mm diameter and 150mm in height (Fig. 1) is upset (open die forged) at 1200° C to 100mm height disk (Fig. 2). Material of the workpiece is low carbon steel. A graphite lubricant reduces the friction to u=0.25. A press with 2-m/sec speeds is used to make this part. At 1200° C the material has the values for its C=48MPA and m=0.08 parameters Fig. 1 Height=150mm, Diameter=100mm Fig. 2 Height = 100mm, Diamete = ? mm (a) (b) (c) Determine the final diameter of the disk (see Fig. 2) Determine the true strain rate at the end of process. Calculate the flow stress at the end of the stroke.
7. Which one is coarser? (a) Abrasive paper: 180 grit paper or 320 grit paper ANS: (b) Metal specimen: ASTM grain-size number; 4 or 10 ANS:
If the plate thickness in the previous problem were 1 cm, would the thickness be sufficient for a JIC test? Assume these material properties: E = 205 GPa, v = 0.25.
Follow up: How would the steps of this problem change if θ was not 90°?
69 alll O ... ۱:۲۰ ۱ ص Sheet 3.pdf Sheet 5 Fatigue Design Note: Assume any missing data QI: Aluminum plate shown: Sut=640 Mpa, is 310 MPa Calculate the diameter at the fillet. reliability is 90%, factor of safety is 2, the size Neglect the transverse shear stress. factor is 0.87, notch sensitivity factor is 0.81, machined surface. Determine the plate thickness (t) for infinite life. 0.2d -50 kN 4.5d- P=+ 50 kN +100 100 P-1 50 kN 50 '150KN 100mm 200mm Q5: A steel cantilever shaft.The fillet is 6 mm, Sut= 560 MPa and Sy= 420 MPa. Assume the shaft surface is cold-rolled, operating temperature is 550c, reliability is 50%. Calculate the design safety factor Nrusing Good-Man theory of failure. Q2: A rotating steel shaft shown: carried by bearings A and E. Machined surface, Su = 500 MPa, reliability is 90%, r=3 mm. What is the life of the shaft if design factor 3? 100 100 js KN 200 300 R6 400N M-- ---- 025 6ODN 3r -3r A 300 350 450 500N 250N Q3: A steel cantilever beam: Sut = 550 MPa, notch…