Each phase of a balanced three-phase -connected load consists of a 200 mH inductor in series with the parallel combination of a 5 µF capacitor and a 200 ohms resistan Assume zero line resistance and a phase voltage of 200 V at w = 400 rad/s. a) the magnitude of the phase current is A. Do not write units, round off to three(3) decimal places b) the magnitude of the line current is A. Do not write units, round off to two(2) decimal places c) the total power absorbed by the load is W. Do not write units, No decimal places

Each phase of a balanced three-phase -connected load consists of a 200 mH inductor in series with the parallel combination of a 5 µF capacitor and a 200 ohms resistan Assume zero line resistance and a phase voltage of 200 V at w = 400 rad/s. a) the magnitude of the phase current is A. Do not write units, round off to three(3) decimal places b) the magnitude of the line current is A. Do not write units, round off to two(2) decimal places c) the total power absorbed by the load is W. Do not write units, No decimal places

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of the load impedance Z=ZZ, find expressions for P and Q, from complex power considerations. (b) Express p(t) in terms of P and Q, by choosing i(t)=2Icost. (c) For the case of Z=R+jL+1/jC, interpret the result of part (b) in terms of P,QL, and Qc. In particular, if 2LC=1, when the inductive and capacitive reactances cancel, comment on what happens.
Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax
Need asap pls help. Solve for the voltages across and currents through each component. Show the complete solution and explain. The total power should be zero..
The values of the elements for the given circuit are given below.The maximum average power that can be transferred to the ZL load iswhich one?R1 = 400 OhmsL = 1000j OhmsR2 = 500 Ohms
15 A of current is taken by a non-inductive load at 125 V. In order that the same current shall be generated from 240 V, 50 Hz mains. An inductor is now also then connected in series. Note: The resistance of the inductor should be ignored and also assume the waveform to be sinusoidal. Determine the phase difference between the current and the applied voltage, the impedance of the circuit and the inductance of the inductor.
= = Impedances Z₂ and z3 in parallel are in series with an impedance z₁ across a 100V,50Hz AC supply. Z₁ (6.25 +j1.25)ohms, Z₂ = (5 + j0)ohms and Z3 (5 - jxc)ohms. Determine the value of capacitance Xc said that the total current of the circuit will be in phase with the total voltage. What is then the circuit current and power?
lši vl pir:10 Expert Q&A + 1. For the circuit in Figure: a. Determine I, VR, and Ve in phasor form. b. Calculate the total power factor, and indicate whether it is leading or lagging. c. Calculate the average power delivered to the circuit. d. Draw the impedance diagram. e. Find the voltages VR and Vcusing the voltage divider rule and compare them with the results of part(a) above. + Uc - + Ug - 30 2 L = 0.2 H L =0.2 H C = 4 µF e = V2(20) sin(377t + 40°) Expert Answer Home Search More II
In the 3-phase circuit in the figure, f = 2000 Hz. Find line and phase voltages and currents for the load.(in amplitude and phase).
Two impedances consist of resistance of (15 ohms and series connectedinductance of 0.04 henry) and (resistance of 10 ohms, inductance of 0.1 henryand a capacitance of 100 microfarad, all in series) are connected in series andare connected to 230 volts, 50 – Hz AC source. Find: (a) current drawn, (b) voltageacross each impedance, (c) individual and total power factor. Draw the phasordiagram.
A 60 Hz sinusoidal voltage v = 141sinwt is applied to a series RL circuit. The values of the resistance and the inductance are 3 ohms and 0.016 henry respectively. a) Compute the rms value of the current and its phase angle with respect to the voltage.b) write the expression of the instantaneous current.