Evaluate the convection heat transfer coefficient for the flow of (a) air and (b) water at a velocity of 5 m/s in an 8-cm-diameter and 10-m-long tube when the tube is subjected to uniform heat flux from all surfaces. Use fluid properties at 25° C and assume fully developed turbulent flow in the entire duct.

Evaluate the convection heat transfer coefficient for the flow of (a) air and (b) water at a velocity of 5 m/s in an 8-cm-diameter and 10-m-long tube when the tube is subjected to uniform heat flux from all surfaces. Use fluid properties at 25° C and assume fully developed turbulent flow in the entire duct.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.1P: 6.1 Determine the heat transfer coefficient at the stagnation point and the average value of the...

See similar textbooks

Similar questions

Water at 15ºC is to be heated to 65ºC by passing it over a bundle of 4-m-long 1-cm-diameter resistance heater rods maintained at 90ºC. Water approaches the heater rod bundle in normal direction at a mean velocity of 0.8 m/s. The rods arc arranged in-line with longitudinal and transverse pitches of SL 4 cm and ST 3 cm. Determine the number of tube rows NL in the flow direction needed to achieve the indicated temperature rise.
1. Experimental analysis was carried out about turbulent convective heat transfer in trapezoidal cross-sectioned duct.Average Nusselt numbers and Reynolds numbers were determined for each experiment and the following data set have beenobtained from this investigation. Find an engineering correlation between the average Nusselt number and Reynolds numberin the form ofNu = aReb
Air at 1 atm and 20°C flows in a 3-cm-diameter tube. The maximum velocity of air to keep the flow laminar is (a) 0.87 m/s (b) 0.95 m/s (c) 1.16 m/s (d) 1.32 m/s (e) 1.44 m/s
Heated air at 1 atm and 100°F is to be transported in a 900-ft-long circular section plastic duct at a rate of 1.4 lb/s. I want to determine the head loss and pumping power at the three diameter values in the table below. Complete the table to help me choose a wise diameter. Why would a good design not only focus on minimizing the pumping power? Diameter Head loss, hi Pumping power, W Reynolds number, Re n.d. f n.d. (in) ft hp 8 12 16
Engine oil flows at a rate of 0.05 kg/s through a section of a 2.5 cm diameter tube. The oil enters the section at a temperature of 50 C. The tube wall is kept at 20 C, and it can be assumed that the flow through the section is fully developed. The section of the tube is 5 m long. (a) What is the exit temperature of the oil? (b) What is the heat transfer rate from the oil to the tube wall?
An electronic device is cooled by water flowing through capillary holes drilled in the casing as shown in below figure. The temperature of the device casing is constant at 353 K. The capillary holes are 0.3 m long and 2.54x10-3 m in diameter. If water enters at a temperature of 333 K and flows at a velocity of 0.2 m/s, calculate the outlet temperature of the water. 0.3 m 0000000000 Surface Water 333 K 0.2 m/s 2.54 x 10m temperature = 353 K Water Capillary holes Single capillary
Water at 10oC enters a tube of 0.1 m diameter at the mean flow velocity of 0.4 kg/s. Calculate the exit water temperature if the tube is 15 m long and the wall temperature is constant 30oC.
- EXAMPLE 8-1 Laminar Flow in Horizontal and Inclined Pipes Consider the fully developed flow of glycerin at 40°C through a 70-m-long, 4-cm-diameter, horizontal, circular pipe. If the flow velocity at the centerline is measured to be 6 m/s, determine the velocity profile and the pressure dif- ference across this 70-m-long section of the pipe, and the useful pumping power required to maintain this flow. For the same useful pumping power input, determine the percent increase of the flow rate if the pipe is inclined 15° downward and the percent decrease if it is inclined 15° upward. The pump is located outside this pipe section. D-2 em 6 m/s Glycerine Hello sir, I want the same solution, but in a simplified way without the words of simplifying the solution. ur) - u I- Substituting, the velocity profile is determined to be u(r) - (6 m/s)1- - 6(1-2500r) (0.02 m) where u is in m/s and r is in m. The average velocity, the flow rate, and the Reynolds number are 6 m/s V - Vs - 3 m/s V - VvA-…
- EXAMPLE 8-1 Laminar Flow in Horizontal and Inclined Pipes Consider the fully developed flow of glycerin at 40°C through a 70-m-long, 4-cm-diameter, horizontal, circular pipe. If the flow velocity at the centerline is measured to be 6 m/s, determine the velocity profile and the pressure dif- ference across this 70-m-long section of the pipe, and the useful pumping power required to maintain this flow. For the same useful pumping power input, determine the percent increase of the flow rate if the pipe is inclined 15° downward and the percent decrease if it is inclined 15° upward. The pump is located outside this pipe section. D-2 em 6 m/s Glycerine Hello sir, I want the same solution, but in a simplified way without the words of simplifying the solution. ur) - uma 1- Substituting, the velocity profile is determined to be ur) - (6 m/s)I - - 6(1 - 2500r) (0.02 m) where u is in m/s and r is in m. The average velocity, the flow rate, and the Reynolds number are V - Vavs 4max 6 m/s - 3 m/s…
Consider laminar flow through a very long straight section of round pipe, that the velocity profile through a cross-sectional area of the pipe is parabolic with the axial velocity component given by V = 2Vavg(1 − r2/R2) where R is the radius of the inner wall of the pipe and Vavg is the average velocity. Calculate the momentum-flux correction factor through a cross section of the pipe for the case in which the pipe flow rep resents an outlet of the control volume
Water is flowing through a 25-mm diameter and 10-m long tube. The water enters the tube at 20\deg C with a mass flow rate of 0.2 kg/s. The outlet mean temperature is 60\deg C, and the tube surface temperature is maintained constant. Determine the hydrodynamic and thermal entry.lengths. Is the flow fully developed? What is the convective heat transfer coefficient inside the pipe?
Air at 1 atm and 20°C is to be transported in a 60-m-long circular steel duct at a rate of 5100 L/min. The roughness of the duct is 0.25 mm. If the pressure drop in the pipe is not to exceed 90 Pa, the maximum velocity of the air is (a) 3.99 m/s (b) 4.32 m/s (c) 6.68 m/s (d) 7.32 m/s (e) 8.90 m/s