Example 2 A cylinder of 0.12 m radius rotates concentrically inside a fixed hollow cylinder of 0.13 m radius. Both the cylinders are 0.3 m long. Determine the viscosity of the liquid which fills the space between the cylinders if a torque of 0.88 Nm is required to maintain an angular velocity of 2n rad/s.

Example 2 A cylinder of 0.12 m radius rotates concentrically inside a fixed hollow cylinder of 0.13 m radius. Both the cylinders are 0.3 m long. Determine the viscosity of the liquid which fills the space between the cylinders if a torque of 0.88 Nm is required to maintain an angular velocity of 2n rad/s.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.90P: The hemispherical glass bowl is filled with water. Find the location y of the center of gravity of...

See similar textbooks

Similar questions

Evaluate the dimensionless groups hcD/k,UD/, and cp/k for water, n-butyl alcohol, mercury, hydrogen, air, and saturated steam at a temperature of 100C. Let D=1m,U=1m/sec, and hc=1W/m2K.
A full rectangular tank is 3.9m wide, 5m long, and 2.3 deep contains fluid weighting 580kN. Find the following: mass of the fluid kg
Prob.5. Calculate the capillary effect in millimetres in a glass tube of 4 mm diameter, when immersed in mercury. The temperature of the liquid is 20° C and the value of surface tension of mercury at 20°C in contact with air is 0.51 N/m. Take contact angle as 130° and specific weight 133 kN/m².
Answer the following. A: When the pressure of liquid is increased from 3.5 MN/m² to 6.5 MN/m² its volume is found to decrease by (0.08) percent. What is the bulk modulus of elasticity of the liquid? B: An open cylindrical tank (1.2m) in diameter and (1.8m) deep is filled with water and rotated about its central axis at (60 r.p.m). How much liquid is spill and how deep of the water at the central axis.
A very tall 10-cm-diameter vase contains 1178 cm 3 of water.When spun steadily to achieve rigid-body rotation, a 4-cmdiameterdry spot appears at the bottom of the vase. Whatis the rotation rate, in r/min, for this condition?
4. The value of --- specifies whether the fluid can be assumed compressible or incompressible. 5. Archimedes' principle indicates - 6. A truck is filled with gasoline. If the container (tank) on the truck undergoes a then the liquid surface will begin to rotate clockwise about the center of the container and will eventually maintain a fixed tilted position.
For what uniform rotation rate in r/min about axis C willthe U-tube in Fig. take the confi guration shown? Thefl uid is mercury at 20 ° C.
The bottom quarter of a vertical cylindrical tank of total height 0.4 m and diameter 0.3 is filled with a liquid (SG>1, like glycerin) and the ret with water. The tank is now rotated about its vertical axis at constant angular speed w. Determine the value of angular speed in rad/s when point P on the axis at the liquid-liquid interface touches the bottom of the tank.
A 150-mm diameter vertical cylinder rotates concentrically inside another cylinder of 151-mm diameter. Both cylinders are 250-mm in height. The space between the cylinders is filled with a liquid with viscosity of 10 poise. Determine the torque required to rotate the inner cylinder at 100-rpm in N-m.
The physical model of a pipe containing water with kinematic viscosity has been built in the scale of in a laboratory. Find the ratio of velocity of water in the main pipe with kinematic viscosity of to the model. Discuss the difference in the velocities of the model and main pipe.
Using the figure above of a column of fluid, imagine that it is on an elevator that is accelerating upward with acceleration a. What is the force balance for the fluid in terms of Fz? What would the equation be for dP/dz in terms of p, g, and az?
find the answer Gas in enclosed cylinder with a weighted piston as the top boundary. The gas us heated and expands from a volume of 0.04 m^3 to 0.10 m^3. The pressure varies such that PV=consant, and the initial pressure is 200 kPa. Calculate the work done by the system in kiloJoules? Write the answer up to TWO DECIMAL PLACES.