Example 5.15. An overhang crank with pin and shaft is shown in Fig. 5.18. A tangential load of 15 kN acts on the crank pin. Determine the maximum principal stress and the maximum shear stress at the centre of the crankshaft bearing. Crank pin- 15 kN W 140 mm Crank web Crank shaft -120 mm- Fig. 5.18 80 mm

Example 5.15. An overhang crank with pin and shaft is shown in Fig. 5.18. A tangential load of 15 kN acts on the crank pin. Determine the maximum principal stress and the maximum shear stress at the centre of the crankshaft bearing. Crank pin- 15 kN W 140 mm Crank web Crank shaft -120 mm- Fig. 5.18 80 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two pipes were connected by a flanged bolt coupling. The material properties are as follows: For outer bolts, 12 pieces, 16 mm diameter, on a mean radius of 150 mm, G = 28 GPa. For the inner bolts, 8 pieces, 12 mm diameter, on a mean radius of 100 mm, G = 20 GPa. Determine the total torque of the system if the shearing stress is limited to 30 MPa in the bolts. (Draw also the FBD) with complete solution
A flexible cable and rigid boom system is used to lift a load of 65kN at the end of Boom at point C. Points A and B are considered pinned in nature. The allowable shearing stress at all bolts are 250MPa and the allowable bearing stress at all bolts are 300MPa. Note that the initial position of boom is horizontal and segment A and B are vertical. Determine the horizontal reaction at A. 3. Determine the vertical reaction at A.
For the frame shown, a 4226-N load is acting on member ABD at D. If the allowable material shear stress for is 42 MPa, determine the required diameter (rounded off to the nearest 2.5 mm) of the pins at C and D. Pin C and pin D are subjected to double shear and single shear, respectively. If the thickness of member BC is 12 mm and that of member DE is 16 mm, determine the maximum bearing stress at C.
Q-1 ) A thin cylinder of inner radius 150 mm and thickness 9 mm is subjected to an internal pressure of 9 MPa. The average circumferential (hoop) stress in MPa is equal to ?
The lap joint shown is fasted by 20mm diameter rivets. Calculate the maximum safe load P that can be applied if the shearing stress in the rivet is limited to 96MPa and the bearing stress is limited to 124 MPa. Assume the Applied load is uniformly distributed among the four rivets.
A flange coupling connects two 2 inch diameter shaft. The flanges are fitted by 6 bolts on a 7 “ bolt circle. If the shaft rotates at 300 rpm and transmit 45 hp, determine the required bolt diameter when allowable shear stress of 11,000 psi.
The maximum torsional shear stress of a shaft with diameter D can be found at what distance from the center of the shaft?
A composite shaft is made by slipping a bronze tube of 3-in. outer diameteran -in. inner diameter over a solid steel shaft of the same length and 2-in.-diameter. The two components are then fastened rigidly together at their ends. What is the largest torque that can be carried by the composite shaft if the working shear stresses are 8 ksi for bronze and 12 ksi for the steel? For bronze, G = 6 x 106 psi, and for steel, G = 12 x 106 psi
A 3-m long thin-walled tube has an equilateral triangular cross-section with a constant thickness of 10 mm. If each side of the triangle is 200 mm measured at the median line and the allowable torsional stress is 40 MPa, what is the angle of twist in radians? (Use G = 70 GPa)
The riveted lap connection shown consists of two(2) – PL 12 mm × 280 mm. 1. If allowable shearing stress in 20mm rivets is 186 MPa, find the maximum allowable force P that can be applied a. 233.734 kN b. 251.813 kN c. 283.406 kN d. 245.916 kN 2. If allowable bearing stress in holes is 1.2Fu where Fu is the ultimate strength of the plate and which is equal to 400 MPa, find the maximum allowable force P that can be applied neglecting effect of eccentricity. a. 563.3 kN b. 460.8 kN c. 683. 6 kN d. 405.9 kN 3. If allowable yielding of gross area is Fy/1.67, where Fy is the yield strength of the plate and which is equal to 250 MPa, find the maximum allowable force P that can be applied neglecting effect of eccentricity. a. 534 kN b. 560 kN c. 446 kN d. 503 kN 4. If diameter of hole equals diameter of rivet, what is the net area of edge-3-4-edge in square…
A flywheel is to be fitted on a punching machine with 73% mechanical efficiency. The machine makes 20 working strokes per minute. The holes are 20-mm diameter, thickness of 12 mm steel plates with an ultimate shear strength of 330 MPa. The punching operation takes place during 1/9th of a revolution of the crankshaft. Determine the capacity (kW) of a driving motor necessary to operate a punching machine.
In Problem 1, determine the required diameter of the pin at A if the allowable stress is 60 MPa (double shear