Exercise #3 The Si Darlington transistor pair has negligible leakage current, and B, = B2 = 50. Let Vcc = 12V, R = 1k2, and R, to be a very large value (approaching infinity). • Find the value of R, needed to bias the circuit so that VCE2 = 6V • Find the resulting VCE1 Vec R1 maxim Ca integrated-

Exercise #3 The Si Darlington transistor pair has negligible leakage current, and B, = B2 = 50. Let Vcc = 12V, R = 1k2, and R, to be a very large value (approaching infinity). • Find the value of R, needed to bias the circuit so that VCE2 = 6V • Find the resulting VCE1 Vec R1 maxim Ca integrated-

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

04:- Design a bias circuit for NPN silicon transistor having a nominal B-100 to be used in voltage divider circuit with Q-point of Ic 10 mA and VCE = 10 V. Use standard valued 5% resistors and draw a schematic diagram of your design. (10 points)
7. MOSFET circuit The MOSFET in the circuit below has V, = 1 V and kn = 4 mA/V². a) Is the MOSFET operating in saturation or in the triode region? b) Determine the drain current Ip and Vout: + 5 V 5 k Vout
Identify the source, drain, gate, and bulk terminalsand find the current I in the transistorsAssume VTN = 0.70 V
Draw, Illustrate and label your schematic diagram before solving the problem. 3) Given an Emitter-Stabilize Biased transistor circuit with beta DC is 250,Base resistor is 150 ohms, collector resistor is 1.5k ohms ,emitter resistor is 500 ohms ,emitter voltage supply is -5v and Voltage at common collector is +28V,Voltage at Base-emitter junction is 0.7v,. Determine Base current, Collector current and Voltage at collector-emitter junction.
A 4.7 zener diode is connected to the base resistor. The left side of the resistor sits at about 12V. The right side of the biasing resistor is connected to the Zener and npn transistor. The Zener bias is 5mA. The base current needed is 80uA. What is the appropriate resistor for this circuit? (In kohms) I
c. For the circuit shown in Figure, determine lc and VCB. Assume the transistor to be made of Silicon. Ic RE=1.6 kn Rc=1.1 kn EE=8 V Vcc= 20 v
Q2: A transistor dissipates 50W in an ambient temperature of 60°C, the thermal resistances are 0-0.5 °CW¹, 8ca-4 °CW'. Determine the junction temperature without a heat sink. Determine the thermal resistance of the heat sink to avoid the junction temperature exceeding 180°C. 3
A Bipolar junction Transistor with curreat amplification factor being 100, Input Base current is 50μA. Collector voltage is 10 V and biasing voltage being +20 V. Find followings a. Collector current b. Resistance (R1) c. Collector voltage , Emitter voltage , Base Voltage & Collector-Emitter Voltage.
Design the following MOSFET circuit for it to operate in saturation mode with 0.5 mA drain current. Determine Rp and dc voltage VĎ. Assume V₁ = 2 V and K = 0.1 mA/V² for this MOSFET. 10 V RD -VD
Q-3. Find the drain-source voltage, Vos, for the E- MOSFET circuit given below. The device parameters are: Ioss = 4 mA and Vm = 2 V. +15V Rp- 2k 4M R1 + Vps 2M R2
Q6:A) A transistor dissipates 50W in an ambient temperature of 60°C.The thermal resistance are exc-0.5 the junction temperature without a heat sink. Determine the thermal resistance of the heat sink to avoid the junction exceeding 170°C. °CW¹,0a-4°CW.Determine 5% single polver supply
A certain npn silicon transistor has vBE=0.7 V for iB=0.1 mA at a temperature of 30°C. Sketch the input characteristic to scale at 30°C. What is the approximate value of vBE for iB = 0.1 mA at 180°C? (Use the rule of thumb that vBE is reduced in magnitude by 2 mV per degree increase in temperature.) Sketch the input characteristic to scale at 180°C.