Figure 1.2 shows a floor plan consisting of a one-way slab spanning betweenbeams on grid lines A, B, C, and D. The beams are supported on columns at theintersections of numbered and lettered grid lines. Unfactored dead and live loadscarried by the slab are shown. a)Compute the factored dead and live loads based on 1.2D and 1.6 L. b)Determine the tributary width for the beam on Line B and the total factored load (plf) carried by the beam. (Neglect beam weight) c) Determine the tributary area for the column at the intersection of Lines B and 2. Compute the total factored load (lbs) transferred to the column. Assume the column is 12 in. x 12 in.

Figure 1.2 shows a floor plan consisting of a one-way slab spanning betweenbeams on grid lines A, B, C, and D. The beams are supported on columns at theintersections of numbered and lettered grid lines. Unfactored dead and live loadscarried by the slab are shown. a)Compute the factored dead and live loads based on 1.2D and 1.6 L. b)Determine the tributary width for the beam on Line B and the total factored load (plf) carried by the beam. (Neglect beam weight) c) Determine the tributary area for the column at the intersection of Lines B and 2. Compute the total factored load (lbs) transferred to the column. Assume the column is 12 in. x 12 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1- For the floor system shown in Figure below, support service live load 4KN / (m ^ 2) and service dead load 5KN / (m ^ 2) Answer the flowing. Classify the floor system into one way or two-way solid slab. 2- What is the minimun slab thickness that should be used to control deflection and shear requirement ? 3- By using Ø 12 mm rebar, what is the required positive and nagative reinforcement? 4- Sketch the detail of reinforcement. Use : fy = 400Mpa , f c ^ prime =30 Mpa 6.00 m 6.00 m6.00 m 3.00 m 0.30 m АB 3.00 m 3.00 m
Determine the reinforcements for given slab systems and draw a sketch to show bar arrangements 0:25 hf=12 cm 3.25 3.50 h 120 mm Q = 2.0 kN/m² (for Slabs) Q = 5.0 kN/m² (for Balcony) 025 hf 12 Gm 3:25 4150 025 #7 hf 12 cm 3.25 19:40 025 + hf 12 cm 3.RS 3.50 Yconcrete 25 kN/m³ Coverage+plaster= 1.5 kN/m² Materials: C25/S420
A rectangular footing 2.3 m x 3.2 m x 0.34 m thick supports a 300 mm square column at its center. Column loads are service conditions: DL = 341 kN LL = 216 kN f’c = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm Calculate the ultimate punching shear stress in the slab. Write your final answer with 2 decimal places if the unit is MPA.
1-Explain about two-way slab with neat diagram. 2- Write all the assumptions made in theory of pure bending. 3- Write any three differences between one way and two-way slab. 4- Explain about slender column and its failure pattern.
Identify types of each slab panel and label the shear force coefficient for loading distribution according to Table 3.15 BS8110. (*all unit in m) B1 A B 0.5 3 5.5 2 2.5 6.5 6.5 3,
A rectangular footing 2.1 m x 3.6 m x 0.35 m thick supports a 300 mm square column at its center. Column loads are service conditions: DL = 346 kN LL = 231 kN f’c = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm Calculate the nominal punching shear stress in the slab. Write your final answer with 2 decimal places if the unit is MPA. Answer: 1.83
A square footing 2.4 m x 0.34 m thick supports a 300 mm square column at its center. Column loads are service conditions: DL = 326 kN LL = 219 kN f'c = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm Calculate the nominal one way shear stress in the slab. Write your final answer with 2 decimal places if the unit is MPa
ANALYSIS AND DESIGN OF ONE-WAY SLABS: A slab that is 1.8 meters x 4 meters carries a superimposed dead load of 3.5 kPa and a live load of 5 kPa. Design Criteria: f'c = 28 MPa fy = 350 MPa tslab = 125mm unit weight of concrete = 23.54 kN/m³ Design the slab's reinforcement (main and temperature bars). 4 meters 1 m strip 1.8 meters
Determine the maximum live load that can be applied on one way slab shown in Fig. (1). The slab is reinforced with main reinforcement of $12@150 mm at top and bottom f = 25 MPa, fy = 400 MPa, Wa = slab weight + 40mm tiling Slabthickness = 180 mm All columns = 300*300 mm All beams = 300 * 600 mm 0.3 H 11 11 11 11 7m 11 11 10.3 3m = 0.3 3m 10.3 Fig.(1) 0.3 +H
A square footing 2.1 m x 0.31 m thick supports a 300 mm square column at its center. Column loads are service conditions: DL = 302 kN LL = 248 kN f’c = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm Calculate the maximum ultimate bending moment in the slab. Write your final answer as whole number with the unit of kN-m.
Figure 1.2 shows a floor plan consisting of a one-way slab spanning betweenbeams on grid lines A, B, C, and D. The beams are supported on columns at theintersections of numbered and lettered grid lines. Unfactored dead and live loadscarried by the slab are shown. a)Compute the factored dead and live loads based on 1.2D and 1.6 L. b)Determine the tributary width for the beam on Line B and the total factored load (plf) carried by the beam. (Neglect beam weight) c) Determine the tributary area for the column at the intersection of Lines B and 2. Compute the total factored load (lbs) transferred to the column. Assume the column is 12 in. x 12 in. 22-144 200 SHEETS O 3 18' SE Dead: Live: 20' Unfactored Loads W₁ = 100pst W₁ = 70 psf Beam on Line B: Column on Beams Line B/2 Columns One-way slab 4 FLOOR PLAN 20' Trib.width = C 1 Trib. area = - Factored Loads_ 20' Beam Load= Column Load=