Q5Figure 5 shows the circuit diagram for a two-stage amplifier. You may assume that theparameter is B= 0.03 A/V?, V = 0.5 V, and VA = 12 V for each transistor. All othervalues are shown beside the schematic.(а)What kind of configuration is used for the 2 stages amplifier?(b)What kind of amplifier is M1 part of ? and what about M2?In which region should both transistors operate for a better voltageamplification gain? Calculate the corresponding DC Ins for Mi and M2.(c)(d)Calculate transconductances gm and output resistances ro for both M1 and M2.Draw the combined small-signal equivalent circuit suitable for mid bandfrequency range analysis. State any assumption.(e)(f)Determine the numerical values for:(i) Voltage gain of the entire amplifier.(ii) Output resistance of the entire amplifier.VDDVDD = 2VRp2R = 4KNR2 = 4KQR1Rp1HE VoutCp2M2M1Vin HRp1 = 4K2Rp2 = 4K2Rsi = 4KQCGR2|Rsı +CsıRs2 +Cs2Rs2 = 6KN%3DVss = 0 VFigure 5

Answered: Image /qna-images/answer/07d363b1-ea60-4358-8fb0-1dc0284239a0.jpg

Figure 5 shows the circuit diagram for a two-stage amplifier. You may assume that the parameter is B= 0.03 A/V?, Vi = 0.5 V, and VA = 12 V for each transistor. All other values are shown beside the schematic. (a) What kind of configuration is used for the 2 stages amplifier? (b) What kind of amplifier is M1 part of ? and what about M2? In which region should both transistors operate for a better voltage amplification gain? Calculate the corresponding DC IDs for Mi and M2. (c)

Figure 5 shows the circuit diagram for a two-stage amplifier. You may assume that the parameter is B= 0.03 A/V?, Vi = 0.5 V, and VA = 12 V for each transistor. All other values are shown beside the schematic. (a) What kind of configuration is used for the 2 stages amplifier? (b) What kind of amplifier is M1 part of ? and what about M2? In which region should both transistors operate for a better voltage amplification gain? Calculate the corresponding DC IDs for Mi and M2. (c)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q5.Consider the differential amplifier shown in Figure 5 with transistorparameters B=150, VBEO) = 0.7 V, and V. Design the circuit such that the Q-point values are Ic Ica 100μA and voi-vo2 1.2 V for v=v₂-0.0 +3 V VOI -3 V Figure 5.
Q.) Figure below divider bras amplifier Circuit. Givent the model Parameter : gm = 5o mS emitter (CE) Voltage BJT hibrid- TT Shows a Common riT: 6 Kr and to %3D : 00 +Vc. RI C2 Tooks touf RL Vo ihe 200 RE TCE Vs 20 a Draw the Ac eQuivalent at low Freauency Circuit Zi and b.) Determine inPut impedance at mid FreaUincy OutPut imPedance Z0 c.) Calculafe two low Cut -oFF FreQuen Cies FLC1 and FLC2 Ci and E2 respectively Such as due to the exterda al capacitors
I need to design a multi stage amplifier with the following specs:
What is an A/D converter with Voltage-to-Frequency Conversion (VFC)? What is the working principle?
If the amplifier in Figure 4 operates with Rsig= 10 kQ and a load of RL=2kQ. Draw the re model alternating current (ac) equivalent circuit of the amplifier. Determine the input and output impedances. Determine the voltage gain Vo/Vin and Vo/Vsig. Calculate the current gain Io/Ii.
Calculate the output impedance for small-signal equivalent circuit. (R=10 k2, r. =10 k2) ER Rout O A) Rout = 3.3 ka O B) Rout = 20 ko )C) Rout = 30 ka DI Rout = 5 k0
Introducion to Electronic Analysis and Design - CE05 To have a good amplifier Select one: a. The input resistance should be high b. the output resistance should be high c. the voltage gain should be equal to zero d. the current gain should be equal to zero Ssment CE255/EE255 (O1)- Dr. Mamoun Al-Mistar Jump to...
Draw the equivalent circuit for summing amplifier and voltage amplifier inverting non-inverting
The transistor parameters for the circuit in Figure are B1 =B2 = 100, VBE1(on) = VBE2(on) = 0.7 V, and VA1 = VA2 %3D =00.Find the small signal voltage gain Av = vo/vs. (Note that VT=0.026 V) %3D Vcc=9 V Rib Q2 1 ko -R. 20 V 100 Q -14.76 O 0.899 -55.3 ww ww
Design a linear amplifier, based on a bipolar junction transistor 2N3904 in common emitter configuration. The supply voltage is 28V. The quiescent operating collector current for the amplifier should be around 10mA. The data sheet for the transistor shows that the DC current gain at this operating current is about 200. Draw the circuit diagram of your design. Label all the components in the circuit. Show all the voltages and currents that you use for calculations in your design. Label them using consistent naming convention.
In the self-biased FET amplifier in the figure, Vdd=20V Rs=1kohm Vgsq=-2.6V IDq=2.6mA. It has values of Idss=8mA, Vp=-6V gos=25mikroS. 12mV a.c. to transistor input. What should be the Rd resistance value so that the output voltage is -24.85mV when voltage is applied? answer: 3.3kohm, 3.6kohm, 4.5kohm, 3.9kohm, 4.2kohm is one of the answers.
II- 1) Draw the circuit of a V-l converter and derive an expression for the output current in terms of input voltage. 2) Draw the neat diagram of analog multiplier using log-antilog amplifiers and explain its operation.