Figure Q1-1 shows a partially sectional view of a bevel gearbox. Thevertical and horizontal forces (Fy and FH) are indicated at the meshing pointof the pair of the bevel gears. Due to the loading condition of the bevelgearbox, certain amount of linear and angular deflections of the input shaftare expected.i)Which types of rolling element bearings would you choose for bothsides (LHS and RHS) to support the input shaft of the gearbox andbriefly explain why?ii)What arrangement would you use to ensure appropriate arrangementof the chosen bearings?LHS BearingRHS BearingFvFHInputshaftFigure Q1-1

Bevel Gear The pitch surface is shaped like a cone, and the teeth are cut along the cone. This is…

Figure Q1-1 shows a partially sectional view of a bevel gearbox. The vertical and horizontal forces (Fv and FH) are indicated at the meshing poit of the pair of the bevel gears. Due to the loading condition of the bevel gearbox, certain amount of linear and angular deflections of the input sha are expected. i) Which types of rolling element bearings would you choose for both sides (LHS and RHS) to support the input shaft of the gearbox and briefly explain why? ii) What arrangement would you use to ensure appropriate arrangemer of the chosen bearings? LHS Bearing RHS Bearing Fv FH Input shaft Figure Q1-1

Figure Q1-1 shows a partially sectional view of a bevel gearbox. The vertical and horizontal forces (Fv and FH) are indicated at the meshing poit of the pair of the bevel gears. Due to the loading condition of the bevel gearbox, certain amount of linear and angular deflections of the input sha are expected. i) Which types of rolling element bearings would you choose for both sides (LHS and RHS) to support the input shaft of the gearbox and briefly explain why? ii) What arrangement would you use to ensure appropriate arrangemer of the chosen bearings? LHS Bearing RHS Bearing Fv FH Input shaft Figure Q1-1

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter10: Fixed-axis Rotation

Section: Chapter Questions

Problem 46P: At its peak, a tornado is 60.0 m in diameter and carries 500 km/h winds. What is its angular...

See similar textbooks

Similar questions

Determine the angular acceleration of link AB if link CD has the angular velocity wcD = 3 rad/s and angular deceleration aCD = 3 rad/s shown in (Eigure 1). Assume the counterclockwise rotation as positive Figure 1 of 1 Express your answer to three significant figures and include the appropriate units. 0.6 m 0.6 m ? Value O AB rad 0.3 m
F Pivot d The length of the pool cue is 1.5 m. A force of 11 N is applied at an angle 55°, a distance 0.7 meters from the pivot. What is the torque created? Answer to 3 sig figs.
The power of a bus engine is transmitted using the belt-and- pulley arrangement shown. The engine turns pulley A at WA = (30t + 50) rad/s clockwise, where t is in seconds. (Figure 1) Part A Determine the angular velocity of the generator pulley B, measured clockwise, when t = 3 s. Express your answer using three significant figures. Enter positive value if the angular velocity is clockwise and negative value if the angular velocity is counterclockwise. μν ΑΣφ I1 vec WB = rad/s Submit Request Answer Figure Part B Determine the angular velocity of the air-conditioning pulley C, measured clockwise, when t = 3 s. 100 mm Express your answer using three significant figures. Enter positive value if the angular velocity is clockwise and negative value if the angular velocity is counterclockwise. 25 mm WB Πνα ΑΣφ ? vec D. 75 mm wC = rad/s 50 mm WA Submit Request Answer
Compute the torques produced by the following forces. Be sure to indicate whether the torque action is CW or CCW.
A 1.2kg bike wheel, is spinning 210rpm clockwise when a student applies a frictional force as shown. The moment of inertia of any ring (such as the bike tire, 10cm neglecting the spokes) is I = mr2. Answer all questions realtive to the center of the wheel. What is the initial angular speed (in selectable units)? rad/s How much torque does the friction cause? unit What is the moment of inertia? unit What is the angular acceleration? unit How long will the wheel take to stop spinning? unit : How far will the wheel rotate before stopping? 2.65N rad revolutions
Question - Three Asmall Water turbine is of the axial typeranel is installed in a river barrage where the level drapris (18m).. The rotor tip and hum diameters are (1.5 m) and (0.62)m respectively. The rotational speed is (45. rod/s). The axial flow through the O k rador, is (10 m/s), the (~1/hagd = 0.92) and the Mechanical and other losses are (0.05). Find the blade angles and output power - at the mean radius, (Por. Ber and Pont). Assume No Swirl at the outlet)
Using a forked rod, a 0.6-kg smooth peg P is forced to move along the vertical slotted path r= (0.5 0) m, where O is in radians. The angular position of the arm is 0-() rad where t is in seconds. The peg is in Determine the magnihide of the force of the rod on the peg at the instant t2s Express your nnswer to three significant figures and include the appropriate units. contact with only one edge of the rod and slot at any instant. (Figure 1) HA F= Value Tnits Submit Previous Answers Requent Anawer X Incorrect; Try Again; 5 attempts remaining Figure 1 of 1 Part B Determine the magnitude of the normal force of the slot on the peg. Express your answer to three significant figures and include the appropriate units. r= (0.50) m N. Value Units Submit Previous Answers Reguest Answer
r = 1.8 mF = 9.2 NFind torque. Indicate both magnitude, including units, and directon
A new truck has tires with a diameter of 31.1 inches. The tires have a tread-life warranty of 55,000 miles. (a) How many radians will the tires rotate through within the full warranty length? rad (b) How many revolutions is this equivalent to? rev 2 MY NOTES ASK YOUR TEACHER PR
blade complete while after being constant te A. circular saw 1500 revolutions in 30 S consting to stop turned off. Assuming decelkration angular what are a) and decekration 2. initial angular speed the
Compute the moment (positive if counterclockwise, negative if clockwise) of the 0.51-lb force about the pivot O of the wall-switch toggle. F = 0.51 1 Answer: Mo 10° 0.875" lb-in.
find the angular acceleration. Needs Complete typed solution with 100 % accuracy.