Find out the local convection coefficient for a flow over a flat plate at a distance of 0.2 m from the leading edge. The fluid is water at 60°C with a velocity of 2 m/s. The plate maintains a uniform temperature. Assume the film temperature to be 40°C. 6442-9 Is the flat plate losing heat to or gaining heat from the water flow? Justify.

Find out the local convection coefficient for a flow over a flat plate at a distance of 0.2 m from the leading edge. The fluid is water at 60°C with a velocity of 2 m/s. The plate maintains a uniform temperature. Assume the film temperature to be 40°C. 6442-9 Is the flat plate losing heat to or gaining heat from the water flow? Justify.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.38P

See similar textbooks

Similar questions

Determine the rate of heat loss from the wall of a building resulting from a 16 km/h wind blowing parallel to its surface. The wall is 24 m long and 6 m high, its surface temperature is 27C, and the temperature of the ambient air is 4C.
5.7 The average Reynolds number for air passing in turbulent flow over a 2-m-long, flat plate is . Under these conditions, the average Nusselt number was found to be equal to 4150. Determine the average heat transfer coefficient for an oil having thermal properties similar to those in Appendix 2, Table 18, at at the same Reynolds number and flowing over the same plate.
7.43 Liquid sodium is to be heated from 500 K to 600 K by passing it at a flow rate of 5.0 kg/s through a 5-cmID tube whose surface is maintained at 620 K. What length of tube is required?
A steam reservoir is covered by a rectangular plate (its length is 1 m and width 2 m). The steam temperature is 95o C, and it is in contact with the plate. Over the outside surface of the plate, water is flowing at a speed of 3 m/sec at a temperature of 25o C. What is the mean Nusselt number over the plate? What is the mean heat transfer convective coefficient over the plate? What is the heat transfer rate to the water?
Determine the convection heat transfer coefficient (in W/m?.K) for air flowing at a velocity of 3 m/s in a 10-cm diameter and 10-m long tube. Air enters the tube at 10°C and leaves at 20°C, i.e. air is heated. Take the property of air at 1 atm and assume flow to be fully developed. For air at 1 atm: Temperature k, W/m-K v, m?/s Pr 15°C 0.02476 1.470x10-5 0.7323 20°C 0.02514 1.516x10-5 0.7309 25°C 0.02551 1.562x105 0.7296 Hint: When the fluid temperature changes, we use its properties at mean temperature, unless otherwise specified. Round your answer to 2 decimal places.
The air at 1 ATM and 35⁰c flow through a cylinder 5 cm in diameter,at Velocity 50 cm/s. The surface temperature of the cylinder is guarded at 150⁰c *)Calculating heat loss per cylinder unit
Air at 27 ⁰C and 1 atm flows over a flat plate at a velocity of 3m/s, assuming the plate is heated its entire length to a temperature of 70⁰C. Heat transferred in first 25 cm of the plate is?
Determine the convection heat transfer coefficient (in W/m2-K) for air flowing at a velocity of 3 m/s in a 10-cm diameter and 10-m long tube. Air enters the tube at 10°C and leaves at 20°C, i.e. air is heated. Take the property of air at 1 atm and assume flow to be fully developed. For air at 1 atm: Temperature k, W/m-K v, m?/s Pr 15°C 0.02476 1.470x10-5 0.7323 20°C 0.02514 1.516×10-5 0.7309 25°C 0.02551 1.562x105 0.7296
Determine the convection heat transfer coefficient (in W/m²-K) for air flowing at a velocity of 3 m/s in a 10-cm diameter and 10-m long tube. Air enters the tube at 10°C and leaves at 20°C, i.e. air is heated. Take the property of air at 1 atm and assume flow to be fully developed. For air at 1 atm: Temperature k, W/m-K v, m?/s Pr 15°C 0.02476 1.470x105 0.7323 20°C 0.02514 1.516x10-5 0.7309 25°C 0.02551 1.562x105 0.7296 Hint: When the fluid temperature changes, we use its properties at mean temperature, unless otherwise specified. Round vour answer to2 decimal nlaces
Determine the convection heat transfer coefficient (in W/m2-K) for air flowing at a velocity of 3 m/s in a 10-cm diameter and 10-m long tube. Air enters the tube at 10°C and leaves at 20°C, i.e. air is heated. Take the property of air at 1 atm and assume flow to be fully developed. For air at 1 atm: Temperature k, W/m-K v, m?/s Pr 15°C 0.02476 1.470x10-5 0.7323 20°C 0.02514 1.516x10-5 0.7309 25°C 0.02551 1.562x10-5 0.7296 Hint: When the fluid temperature changes, we use its properties at mean temperature, unless otherwise specified. Round your answer to 2 decimal places.
b) A 0.4-W cylindrical electronic component shown in Figure Q3b with diameter 0.3 cm and length 1.8 cm is mounted on a circuit board is cooled by air flowing across it at a velocity of 150 m/min and temperature is 40 °C. Take the pressure of air 1 atm and the film temperature to be 50 °C, determine the surface temperature of the component. Resistor 0.4 W D= 0.3 cm Figure Q3b
Engine oil enters the 5 mm diameter pipe at 120°C. The pipe surface temperature is kept at 40°C and the Re number is about 1000. Calculate the heat lost by the fluid for a 30 cm long pipe? Engine oilYou can get its specs at 390K.