Find the interal normal stress in all relevant segments of the bar in the picture. F1BF2 CD F4F6F3F5Find the internal normal stress in all relevant segments of the bar in the picture. The bar has a constant cross sectionheight of 29 mm and a width of 9 mm, except in CD where it has a thickness of 16 mm. Consider the following appliedforces: F1 = 14 kN, F2 = F3 = 9 kN, F4 = F5 = 4 kN and F6 = 24 kN.Perform your calculations with 6 decimals of precision and present your answers in MPa, with 3 decimals ofprecision. Only use the number of boxes needed to present all your relevant/necessary results/answers and presentyour answers from first to last, in the order of the relevant segments you considered from left to right, along the bar.Fill in the boxes you don't need with a single 0.In your answers do not include signs or units (answer in the requested MPa).

Answered: Image /qna-images/answer/a7444e95-3f4c-4e1e-a613-4bd66e3c0428.jpg

Find the internal normal stress in all relevant segments of the bar in the picture. The bar has a constant cross section height of 29 mm and a width of 9 mm, except in CD where it has a thickness of 16 mm. Consider the following applied forces: F1 = 14 kN, F2 = F3 = 9 kN, F4 = F5 = 4 kN and F6 = 24 kN.

Find the internal normal stress in all relevant segments of the bar in the picture. The bar has a constant cross section height of 29 mm and a width of 9 mm, except in CD where it has a thickness of 16 mm. Consider the following applied forces: F1 = 14 kN, F2 = F3 = 9 kN, F4 = F5 = 4 kN and F6 = 24 kN.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.12.19P: A tension member constructed of an L inch angle section (see Table F-4(a) in Appendix F) is...

See similar textbooks

Similar questions

Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
A simply supported beam is subjected to point load P at mid-span. The normal stress on an element at mid-span is known to be ??x= 1.5 ksi. Determine the element stresses lilt is rotated through angle ? = 450• Show these stresses on a sketch of an element oriented at that angle.
Two steel rods are welded together (see figure): the seam is oriented at angle ? = 50°. The stresses on the rotated element are sx1=10 ksi, sy1= -12 ksi, and tx1y1= -5 ksi. Find the state of plane stress on the clement if it is rotated clockwise to align the x3 axis with the longitudinal axis of the rods.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.
A simply supported wood beam is subjected to point load P at mid-span. The stresses on element C are known to be ??x=-92 psi and txy= -7 psi. Find the principal stresses on the element and show them on a sketch of a properly oriented clement.
The state of stress on an element along the hydraulic lift cylinder on a truck is trv= — 5 MPaLFind the maximum shear stress on the clement and show the state of stress on a sketch of a properly oriented clement.
Repeat the previous problem using ? = 50° and stresses on the rotated element: sy1= 70 MPa, ??y1=-82 MPa, and tx1y1=-35 MPa.
‘7.3-11 The stresses on an element are sx= -300 psi and sy= 600 psi. Find the maximum shear stresses on the element and show them on a sketch of a properly oriented clement.
A solid aluminum bar (G = 27 GPa ) of diameter d = 40 mm is subjected to torques T = 300 N - m acting in the directions shown in the figure, Determine the maximum shear, tensile, and compressive stresses in the bar and show these stresses on sketches of properly oriented stress elements. Determine the corresponding maximum strains (shear, tensile, and compressive) in the bar and show these strains on sketches of the deformed elements.
A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a diameter d1= 24 mm and the bottom shaft has a diameter d2= 16 mm. The punch is used to insert a hole in a 4 mm plate, as shown in the figure. If a force P - 70 kN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the upper and lower shaft of the punch?
-11 A solid steel bar (G = 11.8 X 106 psi ) of diameter d = 2,0 in. is subjected to torques T = 8.0 kip-in. acting in the directions shown in the figure. Determine the maximum shear, tensile, and compressive stresses in the bar and show these stresses on sketches of properly oriented stress elements. Determine the corresponding maximum strains (shear, tensile, and compressive) in the bar and show these strains on sketches of the deformed elements.