if you can solve this thank you! Flux density, B esla13Siliconsheet steel1.211100.9080.70605Cast steel0403Cast iron0.20.1200400Field intensity,$00 800 1000(At/m)FIGURE 1.7Magnetization600 Consider the magnetic core shown in the figure and notice that three sides of the core areof uniform width, whereas the forth side is somewhat thinner. The depth of the core intothe page is 10 cm and the coil has 300 turns. Determine the current that will produce 5.0mwb flux in the core. Use the cast steel magnetization curve of figure 1-7 of Sentextbook.10cmT10cm20cm20cm 州5cm10cm

Step 1: Step 2: Step 3: Step 4:

Answered: Flux density, B esla 13 Silicon sheet…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter7: Symmetrical Faults

Section: Chapter Questions

Problem 7.21MCQ

See similar textbooks

Similar questions

Magnetic flux densities for HR steel laminations and CRGO are 1.25 T and 1.75 T respectively then ratio of weight of CRGO laminations and HR laminations (Assuming same densities is for two type of core material and total flux remains the same.) ..
A transformer has primary and secondary turns of 1250 and 125 respectively. It has core cross-sectionof 36 cm2 and its rms flux density is to be limited to 1.4 T (to prevent core saturation). Whatmaximum 50 Hz voltage can be applied on the primary side and the corresponding open-circuitsecondary voltage?The core has a mean length of 150 cm and its relative permeability can be assumed to be 8000. Whatwould be the rms exciting current when the transformer’s primary winding is excited at a voltage ascalculated above? Also calculate the magnetizing susceptance as seen from primary and secondarysides.If the transformer were to be excited at 60 Hz, 1. What should be the maximum primary voltage for thecore flux density limit not to be exceeded? 2. What would be the magnetizing susceptance as seen oneach side in this case?
The number of disc insulators used in a suspension insulator setup with string efficiency 80 %, phase voltage 33 kV, and the voltage across insulator nearest to conductor 11 kV is .......................... Complete the answer.
The hysteresis coefficient of the core material of a power transformer is 110J/ m3. The eddy current coefficient is 132.87J/m3. The volume of the core is 0.005m3, the thickness of the iron is 0.07 m and the maximum flux density is 1.12T. If the supply frequency is 50 Hz: (a) Determine the hysteresis loss (b) Determine the eddy current loss (c) Determine the core loss of this transformer. (d) Explain how the eddy currents are generated. Suggest one method to minimise this loss. (e) Illustrate the hysteresis losses using a fully labelled hysteresis loop.
With base MVA of 150 and base voltage of 33. If the reactance of the transformer is 0.23 pu. The parameter of the reactance of the transformer in the Neplan software is O 1.66 2.30 23 0.23 O Non of them
a core type transforem is constructed with 0.014-in. thick laminations having a uniform width of 2.75 in. If the maximum flux and flux density are, respectively, 6.2 X 10' maxwells and 8.2 X 10 maxwells per square inch and the air spaces between laminations occupy 8 per cent of the stacked core, calculate the number of laminations in the transformer. I
The core of a transformer operating at 50 Hz has an eddy current loss of 100 W/m3 and the corelaminations have a thickness of 0.50 mm. The core is redesigned so as to operate with the same eddycurrent loss but at a different voltage and at a frequency of 250 Hz. Assuming that at the new voltage themaximum flux density is one-third of its original value and the resistivity of the core remains unaltered,determine the necessary new thickness of the laminations. Clear and detailed solution.
In a transformer that has 10 times more turns on the secondary side (side 2) than on the primary side (side 1), the magnitude of the voltage/EMF across the windings on the secondary side, E₂ will be... O a.... 10 times lower than the voltage/emf on the primary side, E₁. O b.... the same as the voltage/emf on the primary side. O c.... always zero regardless of the voltage on the primary side, E₁. O d.... 10 times higher than the voltage/emf on the primary side, E₁.
Compare dielectric properties of oil with solid Insulators and liquid Insulators. Compare dielectric strength of transformer oil, and solid dielectrics, gas dielectrics.
A. Describe the characteristics of amorphous iron that make it suitable for integrated transformer applications. B. What are the key techniques for the fabrication of high quality amorphous materials in general?
a two Core feeder 196 km long Supplies maximum Current 133A at 40ov. The demand is such the Copper loss is that which would be per annum produced by the full load Cument and t Seeko tollowing for lo months. The resistance of Conductor ikm long and imm? section of Conelucfor of cross setionat O.03712 The Value of area as is 15 bais a IŠ 137.5 mm?. The Cost of energy per unit find the powen loss and annual Cosf
Combination circuit what is PT? RT? IT? Voltage Across each load?

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning