For a particular process, the mean value, Xbar, is 1.011 and the mean range value, Rbar, is 0.102. If the product specification is 1.000 +/- 0.050, calculate the process capability for a sample size is 4.

For a particular process, the mean value, Xbar, is 1.011 and the mean range value, Rbar, is 0.102. If the product specification is 1.000 +/- 0.050, calculate the process capability for a sample size is 4.

Practical Management Science

6th Edition

ISBN:9781337406659

Author:WINSTON, Wayne L.

Publisher:WINSTON, Wayne L.

Chapter2: Introduction To Spreadsheet Modeling

Section: Chapter Questions

Problem 20P: Julie James is opening a lemonade stand. She believes the fixed cost per week of running the stand...

See similar textbooks

Similar questions

A customer has specified that they require a process capability of Cp= 1.5 for a certain product. Assume that USL = 1100, LSL = 700, and the process is centered within the specification range. a. What standard deviation should the process have? b. What is the process mean value? c. What can the company do if it is not capable of meeting these requirements?
Suppose that a processoutput is normally distributed with a mean of 30.0 and a variance of 1.44. If the specifications are 30.0 /- 3.25, then compute process capability indices. Is the process capable of meeting specifications?
A process is in statistical control with = 202,5 y s = 2,0. Specifications are atLSL = 196 and USL = 206.a) Estimate the process capability with an appropriate process capability ratio.b) What is the potential capability of this process?c) Items that are produced below the lower specification limit must bescrapped, while items that are above the upper specification limit can bereworked. What proportion of the process output is scrap and whatproportion is rework?d) Because scrap is more expensive than rework, the process has been centered closer to the upper specification limit. If scrap is twice as expensive as rework, is the process mean at the best possible location? What value of the process target would you recommend?
Specifications for a metal shaft are much wider than the machine used to make the shafts is capableof. Consequently, the decision has been made to allow the cutting tool to wear a certain amountbefore replacement. The tool wears at the rate of .004 centimeter per piece. The process has a naturalvariation, σ, of .02 centimeter and is normally distributed. Specifications are 15.0 to 15.2 centimeters.A three-sigma cushion is set at each end to minimize the risk of output outside of the specifications.How many shafts can the process turn out before tool replacement becomes necessary?
Production. Consider again the task of the quality control inspectors in Exercise 22. a) In this context, what is meant by the power of the test the inspectors conduct? b) They are currently testing 5 items each hour. Someone has proposed that they test 10 instead. What are the advantages and disadvantages of such a change? c) Their test currently uses a 5% level of significance. What are the advantages and disadvantages of changing to an alpha level of 1%? d) Suppose that, as a day passes, one of the machines on the assembly line produces more and more items that are defective. How will this affect the power of the test? Exercise 22 Quality control. Production managers on an assembly line must monitor the output to be sure that the level of defective products remains small. They periodically inspect a random sample of the items produced. If they find a significant increase in the proportion of items that must be rejected, they will halt the assembly process until the…
Burger Doodle is a fast-food restaurant that processes anaverage of 680 food orders each day. The average cost of each order is $6.15. Four percent of the orders are incor-rect, and only 10% of the defective orders can be corrected with additional food items at an average cost of $1.75. Theremaining defective orders have to be thrown out.a. Compute the average product cost.b. In order to reduce the number of wrong orders,Burger Doodle is going to invest in a computerizedordering and cash register system. The cost of thesystem will increase the average order cost by $0.05and will reduce defective orders to 1%. What is theannual net cost effect of this quality-improvementinitiative?c. What other indirect effects on quality might be realizedby the new computerized order system?
The specification limits for a product are 9.9 cm and 12.35 cm. A process that produces the product has a mean of 11.18 cm and a standard deviation of 0.52 cm. What is the process capability, Cpk? a. 0.8205 b. 1.571 c. 0.7853 d. 0.75
If the process capability ratio of a centered process is 0.7, and the process mean is 76, what is the average amount of defects per 1 million outputs? a. 16395 b. 35729 c. 71861 d. 51176
86) PLEASE HELP ME WITH THIS Design specifications require that a key dimension on a product measure 106 = 11 units. A process being considered for producing this product has a standard deviation of four units. a. What can you say (quantitatively) regarding the process capability? Assume that the process is centered with respect to specifications.Note: Round your answer to 4 decimal places. b. Suppose the process average shifts to 97. Calculate the new process capability. Note: Round your answer to 4 decimal places.. c. What Is the probability of defective output after the process shift? Note: Use Excel's NORM.S.DIST function to find the correct probability. Round "z" values to 2 decimal places. Round y answer to 4 decimal places.
You work for Raider Data Systems where thousands of insurance records are entered by clerks each day for a variety of client firms. You are in charge of setting control limits to include 99.73% of the random variation in the data entry process when it is in control. Samples that you collected from 20 employees are shown below. You carefully examine 100 records entered by each employee and count the number of errors entered by each clerk. You also compute the proportion defective in each sample. Using a p-chart, what are the upper and lower control limits? Sample Errors Made Proportion Defective 1 4 0.04 2 5 0.05 3 6 0.06 4 3 0.03 5 8 0.08
The upper and lower specification limits for a component are 5.20, and 5.30 ounces, respectively. The process standard deviation is .05, and the process average is 5.24 ounces. a) Calculate Cpk. (Show formula and calculations) b) Does the process posses six sigma capability? Why or Why not? Please explain.
You pull 5 bags of chips off of the production line every hour. The process is currently under control. The average weights are calculated for each sample, and the average of those averages is 129.1. The ranges are calculated for each sample, and the average of those ranges is 4.1. What is the Upper Control Limit for the X-bar chart? Round your answer to one decimal place.