For a vibroflotation work, the backfill to be used has the following characteristics: D50 = 2 mm D20 = 0.7 mm D10 = 0.65 mm Determine the suitability number of the backfill. How would you rate the material?

For a vibroflotation work, the backfill to be used has the following characteristics: D50 = 2 mm D20 = 0.7 mm D10 = 0.65 mm Determine the suitability number of the backfill. How would you rate the material?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A tubewell of 30 cm diameter penetrates fully into an artesian aquifer. The strainer length is 15 m.…

Q: For a vibroflotation work, the backfill to be used has the following characteristics:D50 = 2 mmD20 =…

A: Calculating the stability number: SN=1.73D502+1D202+1D102 =1.7322+10.72+10.652 =3.8607

Q: A 3 m thick clay layer is subjected to an initial uniform pore pressure of 145 kPa as shown in the…

Q: Ex.4: A well of diameter 12 2 in ( capacity = 0.15 bbl/ft ) is drilled by drilling mud of density…

Q: Example (6-3): For the site shown in Figure below (the same site as in Example 6-2), water table…

A: given unit weight of soils 1, soil 2 , soil 3, soil 4 are 18.2, 19, 18.5, 19.2 kN/m3 Water table is…

Q: H.W1: For the raft foundation with dimensions of 20 m show immediate and consolidation settlement of…

A: The given data is: eo=0.9 ef=0.8 E=10 MPa H=4+2 m=6m

Q: A mud sample containing 40lbm/bbl clay has a dial-reading value of 30 cp (at 600 rpm). Calculate the…

A: A plastic viscosity (PV) of the drilling fluid is calculated by subtracting the 300-rpm shear stress…

Q: An exploratory drill hole was made in a stiff saturated clay, as shown in Figure 1, having a…

A: Given Moisture content= 25% Gs= 2.56 , water rose to a height= 3 m FOS = 1.5

Q: Refer to the cross section of the earth dam shown in the figure. Calculate the rate of seepage…

Q: The coefficient of permeability of a sand at a void ratio of 0.62 is 0.03 cm/sec. estimate the…

Q: For the subsoil condition shown in Figure. calculate the total, neutral and effective stresses at 1…

Q: @hasa-mahmhkk Q3) well drilled in Iraq field using the following data: - Depth = 10000 ft Hole…

A: Given:- The depth of the well = 10000 ft The hole diameter of the well = 1.21 ft The drill pipe =…

Q: Q If you are to derive the Terzaghi Theory of 1D consolidation for a half-closed layer, how its…

A: Terzaghi's theory is based on one dimensional consolidation. Half close layer means that there is…

Q: Example 15.46. A clay layer, 8 metre thick, is subjected to a pressure of 70 kN/mt. If the layer has…

Q: A stratum of normally consolidated clay of thickness 10 ft is drained on one side only. It has a…

Q: Discuss Rill erosion and how it can be reduced

A: Question : Discuss Rill erosion and how it can be reduced .

Q: The old building (A) is to be removed and replaced by a new building (B), as shown in the Figure.…

Q: Find the effective average permeability of the deposit in the vertical direction (mm/s).

A: Effective average permeability of the deposit in the vertical direction: option C

Q: A raft 30 × 40m supports a building. The net contact pressure equals 120 kPa; assumed uniformly…

A: given data size of raft=30mx40m contact pressure=120kn/m2 mv=0.32 m2/mn

Q: The value of hydraulic conductivity of the sand is 0.010 cm/sec for porosity of 0.4. Determine the…

A: Given: n1 = 0.4 K1 = 0.010 cm/s n2 = 0.55

Q: Determine the value of void ratio if porosity is 0.402 a:0.65 b:0.69 c:1 d:0.67 e:None of the above

Q: Why for silts the gravity flow is restricted in vacuum dewatering?

A: Methods of gravity, such as deep wells and well points in the fine-grained soils, are not very…

Q: Permeability of the aquifer is ____ m/s

A: To find depth: Determine the saturated thickness of aquifier before pumping ; h0 = depth of surface…

Q: Calculate the consolidated-undrained friction angle and the drained friction angle.

A: Consolidated undrained test

Q: If the breakthrough time for leachate to penetrate a 3-foot thick clay liner is 12 years, estimate…

A: Given- t=12yearsd=3foot=0.9144mη=0.18h=1ft=0.305m

Q: AP = 50 KPa 3 m Sand Ydry = = 16 KN/cu.m GROUND WATER TABLE Sand 6 m Ysat = 18.5 KN/cu.m Clay Ysat =…

Q: A bed of uniform sand having particle size 0.6 mm and specific gravity as 2.68 has porosity 0.42.…

Q: Refer to the cross section of the earth dam shown below. Calculate the rate of seepage through the…

A: Consider the free body diagram α=tan12=26.56o Hence α<30o…

Q: Proctor Test in English unit Method A

A: For Standard proctor test :Compaction effort :E=number of BlowsPer layer×Hammer Weight×Number of…

Q: The following are the results of a consolidation test on a sample of a clayey soil. Pressure, o…

A: Casagrande method was used to determine the liquid limit of soil. Preconsolidation pressure is the…

Q: The compaction of a floor area is carried out in 250 mm thick layers. The hammer used for…

Q: Consider the consolidation situation below and answer the questions. 200 kPa 200 kPa Water Table…

A: Note :- diagram is not required in solution. So not redrawing the same diagram again. Given :-…

Q: Value of hydraulic conductivity of a sand is 0.010 cm/sec at a porosity of 0.45. Determine the…

A: Given: Porosity 1, n1 = 0.45 Hydraulic conductivity at first porosity, K1 = 0.010 cm/s Porosity 2,…

Q: For normally consolidated clay Po - 2 tons/ft? ео — 1.22 Po + Ap = 4 tons/ft2 e = 0.98 The hydraulic…

Q: A 3 m thick clay layer is subjected to an initial uniform pore pressure of 145 kPa as shown in the…

A: given- thickness d=3m=300 cmsingle drainage caseCv=0.03 cm2/mintime factor-tv=0.85

Q: Estimate the total consolidation settlement (primary & secondary) after 2 years and 9 months after…

A: Given, Pier dimension=2 m×3 m Q0=960 kN Unit weight of water=γw=10 kN/m3

Q: A clay specimen drained on both sides was tested. The data were obtained P1=50 kPa e1=0.92 P2=120…

A: Coefficient of compressibility Coefficient of compressibility= ∆e∆σCoefficient of compressibility=…

Q: Compressibililty: Consolidation and Settlement of Soil 500 kN 4m x 3m 3.5m Dry Sand Yary = 15 kN/m…

Q: From the given figure: Tank 10mY = 8kN/m oil G.S. 4m SAND 6m CLAY Determine the loss in pore water…

A: Degree of consolidation = 30 % or 0.30 external pressure increase = γoil ×h = 8×10 = 80 KN/m2

Q: For a normally consolidated laboratory clay specimen drained on both sides, the following are given:…

A: The hydraulic conductivity (K) is given by: K=CV×γw×mv Where, CV = Coefficient of consolidation γw…

Q: The diameter of an open well in coarse sand for a yield of 0.0033 cumec, when operated undera…

A: Given data, Discharge,Q= 0.0033 cumec, Specific capacity, (C/A) = 1m³/h/m²/m H = 3m

Q: Q4 The old building (A) is to be removed and replaced by a new building (B), as shown in the Figure.…

A: Given:- The vertical pressure at the center of the clay layer from building A = 13.64 kN/m2 The…

Q: Q/If wet density was 18 KN /m² and dry density was 14 KN/m- and porosity #04, then find (5) degree…

A: Given: The wet density is 18 kN/m3. The dry density is 14 kN/m3. The porosity is 0.4.

Q: Estimate the settlement of the center of the tank, shown in the sketch, due to consolidation of the…

A: To find - The settlement of the center of tank.

Q: Final height of specimen (cm) Pressure, o' (kg/cm³) 1.9 0.25 1.763 0.5 1.742 1.0 1.702 2.0 1.656 4.0…

A: It is required to determine the area of specimen. A=π4×D2=π4×6.35 cm2=31.67 cm2 It is required to…

Q: d) What is the equivalent permeability which will govern the productivity of the following well? re=…

A: given- ke=500 m/dka=5 m/d

Q: b) For a normally consolidated laboratory clay specimen drained on both sides, the follow are given…

A: Permeability of fluid is the function or quantity that depends on the water content or moisture of…

Q: A soil profile is shown in the figure below. A uniformly distributed load, Ao , is applied at the…

Q: Question: Open channel test is performed and according to the following; (Q = 0.03484 m3/sn)( sill|…

A: y1 = 6.6cm = 0.66m y2 = 1.6cm = 0.16m hL (height of sill ) = 2.5cm

Q: Q-1: Estimate the consolidation settlement due to the lowering of the water table from the location…

A: GIVEN DATA:-⇒γd= 17 KN/m3⇒γsat(sand)= 19 KN/ m3⇒γsat(clay)= 18.6 KN/ m3⇒LL= 40%⇒eo= 0.95

Q: Q: For the soil profile shown in figure. a) Determine the final consolidation settlement. b) If the…

A: Given data Degree of consolidation equation Sand ,clay Unit weights Settlement in 15 months is 25…

Q: 4- A 22 ft clay layer in the field (drained on one side) is normally consolidated. When the pressure…

A: Effective pressure in soil The stress that maintains particles together is known as effective…

Q: Refer to the elog o' curve shown in Figure 8.12. a. Determine the preconsolidation pressure, o. h…

A: Given, It is e log graph. Our aim is to calculate, 1.pre consolidation pressure 2.compression…

Concept explainers

Reactions with Materials

Limestone

Question

Repeat Problem 16.6 with the following:
D₅₀ = 3.2 mm
D₂₀ = 0.91 mm
D₁₀ = 0.72 mm

For a vibroflotation work, the backfill to be used has the following characteristics:
D50 = 2 mm
D20 = 0.7 mm
D10 = 0.65 mm
Determine the suitability number of the backfill. How would you rate the material?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Hey, reply as soon as posible, really really thank u! 1) Investigate and analyze the result obtained from the maximum shear resistance obtained, with the values of the same material provided in the bibliography. The maximum shear resistance obtained is 487 MPa and that of the bibliography is 448 MPa.
Glycerin of density 1260 kg/cum and absolute viscosity 1.5 Pa-s flows at a velocity of 10 m/s in a 10 cm dia pipe. What will be the boundary shear stress (Pa)?
A 100mm* 40 mm* 20 mm steel block is subjected to a hydrostatic pressure of 10MPa. The Young's modulus and Poisson's ratio of the material are 150 GPa and 0.1 respectively. Determine change in volume of the block.
KI-150 md hl=5m K2 60 md h2-10 m K3 300 md h3-7 m The average horizontal permeability? The average vertical permeability?
Question 2 An onshore rig is drilling a production well with drilling pipe with the dimension of 250 mm outer diameter and 130mm inner diameter, see Figure 2. When drilling the drilling pipe, suddenly hit a bedrock which cause the drilling operation stop, see Figure 2. The drilling pipe is made of steel with the modulus of elasticity of 200 GPa and coefficient of thermal expansion is 11.7x10-6/0C. Assuming the initial temperature of the drilling pipe is 27°C and final drilling pipe temperature is 80°C, compute: a) the reaction force at point A and B 130mm Tracing h Snel S 250mm Kelly Sandstone 3500m b) Normal stress exhibit by the drilling pipe c) Is normal stress exhibit compression or tension? 2cm Bedrock 500m F000kN
3) Determine the change of volume caused in the block due to the application of the forces (Bulk Modulus Problem). Set E=60 GPa, poisson Ratio v=0.25, assume isotropic material c=60 mm b= 50 mm K 50 kN 100 kN a = 100 mm → 180 kN
STRENGTH OF MATERIALS answer: 13.8 MN/m2, 5.94 cm from tip of T Please show the solution
A 40 mm diameter rod 6 m long elongates 12 mm under a load of 240 kN. The diameter decreased by 0. 028 mm during the loading. a.) Determine the Poisson’s ratio of the materials, b.) Determine the Young’s Modulus of the material, and c.) Determine the modulus of rigidity of the material.
Please solve question 9-7 using the method of equilibrium. Please do not use stress transformation equations! The answers are given to be Ox’= -61.5 MPa, Tx’y’= 62.0 MPa. Thank you in advance!
ge2. The shear stress at a point in a liquid is found to be 0.03 N/m?. The velocity gradient at the point is 0.15 s1. What will be it's viscosity (in Poise)? a) 20 b) 2 c) 0.2 d) 0.5
The tube is subjected to a torque of 749 N-m Figure 62°5 6 mm 100 mm 4 mm 4 mm 60 mm B 6 mm 1 of 1
A simply supported concrete rectangular beam has a cross-sectional dimension of 200mm x 300mm and length L=(3 + 21/5)m, is to be analyze in flexure, unit weight of the beam is 24kN/m^3. Concrete properties: f'c=28MPA, normal weight concrete, Es=200000MPA