For the 3-reservoir system shown, if the elevation of reservoir A and B is 80 m and 50 m, respectively, and Q₁ is 0.42 m³/s, determine the flow rate in pipe 3. For simplicity, assume the friction factors to be constant for each pipe as shown in the table. A Pipe 1 2 3 Length, L (m) 1800 2000 4000 0.821 cms O a. O b. 0.581 cms O C. 0.621 cms O d. 0.401 cms 2 Diameter, D (mm) 400 500 800 Friction factor 0.02 0.025 0.03

For the 3-reservoir system shown, if the elevation of reservoir A and B is 80 m and 50 m, respectively, and Q₁ is 0.42 m³/s, determine the flow rate in pipe 3. For simplicity, assume the friction factors to be constant for each pipe as shown in the table. A Pipe 1 2 3 Length, L (m) 1800 2000 4000 0.821 cms O a. O b. 0.581 cms O C. 0.621 cms O d. 0.401 cms 2 Diameter, D (mm) 400 500 800 Friction factor 0.02 0.025 0.03

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q2- Water density =1000 kg/m and viscosity is 0.001 Ns/m², is pumped between two reservoirs at 0.2m/s through a 400 m of 8 cm diameter Cast Iron pipe and several minor losses as shown in the figure. Compute the pump power required in kW. Use the last one digit of your ID number for Z1 level in meter. Screwed Z2= 50 m regular 90° elbow Sharp exit Z;= ID m Sharp entrance Half-open gate valve `bend radius Pump Open globe valve 8 cm diameter
Measure the diameter of the pipe next to it, which goes from the discharge nozzle of a pump to the raised reservoir. The following data are known: • • • • • • L1 = 4m; L2 = 88 m; L3 = 75 m; L4 = 7 m. Maximum flow rate Q = 200 m³/h. Elevation elevations: Pump nozzle (H1) = 0.85 m Tank nozzle (H2) = 13.70 m Pump outlet pressure for the flow rate Q considered: P1 = 45 psig = 316 KPa. Maximum height of the liquid in the reservoir above point 2: Hr = 9 m. Maximum reservoir pressure: Pr = 10 psig = 70.3 KPa Specific weight of liquid: y = 9.5 N/dm³ • Kinematic viscosity: v = 550 cks EL. 13,70 my L4 L3 VG VR EL. 0,85 m P1
2. For a piping system as shown in the figure, determine the distribution of the water flow Qi and the piezometric height H at the junction. The powerof the pump is YQH, = 20 kW. constant, equal to inputAssume the friction factor is constant el 30 m Pipe L (m) D (m) f ΣΚ el 15 m 50 0.15 0.02 2 el 10 m [2] 100 0.10 0.015 1 300 0.10 0.025 1 P [1] B [3] 123
Write legibly Complex Pipeline System_Series Pipes 2. Water flows at a rate of 0.020 cms from reservoir A to reservoir B through three concrete pipes connected in series, as shown in the figure. Determine the difference in the water surface elevations in the reservoirs. Neglect all minor losses. Use Hazen – Williams roughness coefficient C = 120 for all pipes. For the solution, use the Hazen – Williams formula. Answer: _______________________________ m
The discharge of water in the given pump is given as 0.030 cubic meters per seconds. Use ywater = 9.79 KN/m° and Pinput = 27.34 hp. Determine the following parameters, if losses and elevation changes is to be neglected. 0.409 MPa 0.125 MPa a. The energy added in meters and the power delivered in kilowatts to the water by the pump. b. The mechanical efficiency of the pump. P 0.04meter Ø 0.1meter Ø
Shown below is an inverted U-tube which is used to drain alcohol from a tank reservoir. The bend of the inverted tube is 1 meter above the free surface of the alcohol in the tank and 10.5 meters above the ground where the alcohol is discharged. Alcohol exits the tube at atmospheric pressure. The Specific gravity of alcohol is 0.89 while g= 9.81. The pressure, in kilopascal, in the bend is Blank 1 P=? 1m
Flow takes place between three reservoirs, as shown in Figure 1. The volume flow rate out of reservoirs A and B is 0,15 m³/s and 0,25 m³/s respectively. If the coefficient of friction for three pipes is 0,008, determine the relative elevations of the free surfaces. Neglect all losses other than friction. May you kindly resend the answers in a different format as they appear blank??
The water is flowing through a pipe having diameters 30 cm and 21 cm at sections land 2 respectively. The rate of flow through pipe is 40 litres/s. The section 1 is 7 m above datum and section 2 is 3 m above datum. If the pressure at section 1 is 37 N/cm? , find the following by neglecting losses: (ENTER ONLY THE VALUES BY REFERRING THE UNIT GIVEN IN BRACKETS) ) Area of cross section of section1 (unit in m?) = Area of cross section of section2 (unit in m?) = velocity at section 1 (unit in m/s) = velocity at section 2 (unit in m/s) = (ii) difference in datum head (Unit in m) = Pressure head at section 1 (Unit in m) = pressure head at section 2 (unit in m) =
Oil (density = 842 kg/m³ and kinematic viscosity = 6.2e - 4 m²/s) is being discharged by a 66 mm diameter, 3 m long horizontal pipe from a storage tank open to atmosphere. The height of the liquid above the centre of pipe is 1 m. Disregarding the minor losses, determine (to 4 decimal places): a) the volumetric flow rate of the oil through the pipe m³/s b) the corresponding Re number.
Determine the flow direction and flow rate for each pipe of the pipe network shown in figure. Not: i)Take the inital values of the flow rates and flow directions shown in figure. ii) Take the Darcy factor f=0.005 in the analysis. Initial flow rates of pipes; Q1= 0.02 m3/s, Q2=0.012 m3/s , Q3=0.016 m3/s, Q4=0.03 m3/s, Q5=0.014 m3/s,Q6=0.014 m3/s, Q7=0.028 m3/s.
The total discharge in the system below is 15.5 cfs and the head loss from B to C is 24 ft. Using n = 0.011 for all pipes, determine the following: (a) flow rate Q2 (cfs) through pipe 2, (b) flow rate Q3 (cfs) through pipe 3, (c) flow rate Q4 (cfs) through pipe 4, (d) head loss h1 (ft) in pipe 1, and (e) head loss his (ft) in pipe 5. 2000 ft 12 in 3000 ft 1500 ft 4000 ft 30 in 10 in 24 in A В D 2500 ft 15 in
Water is flowing downward in a pipe in the figure shown at 0.02 cu. m. per sec. having diameters of 8 cm. and 4 cm. respectively. Determine the values of pressures (a) at pt. 2, P2 and (b) at pt. 1, P1 if the pressure at pt. 1 is twice as great as the pressure at pt. 2. H20 8 ст. Ф 1.5 m 2 datum 4 cm. Đ