For the attached ramp input response of a given sampled-data system y(nT), what is the equation of the system: y(nT) 2.45 1.5 0.63 2T 3T 4T y(nT ) = 0.635(t - 2) + 1.55(t – 3) - 2.458(t - 4) +... y(nT ) = 0.635(t - 2) + 1.58(t – 3) + 2.455(t - 4) +... y(nT ) = -0.635(t - 2) - 1.55(t - 3) - 2.458(t - 4) -.. . y(nT ) = -0.635(t - 2) + 1.55(t - 3) + 2.458(t - 4) +...

For the attached ramp input response of a given sampled-data system y(nT), what is the equation of the system: y(nT) 2.45 1.5 0.63 2T 3T 4T y(nT ) = 0.635(t - 2) + 1.55(t – 3) - 2.458(t - 4) +... y(nT ) = 0.635(t - 2) + 1.58(t – 3) + 2.455(t - 4) +... y(nT ) = -0.635(t - 2) - 1.55(t - 3) - 2.458(t - 4) -.. . y(nT ) = -0.635(t - 2) + 1.55(t - 3) + 2.458(t - 4) +...

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Signal and system problem.plz solve every step with formula
please answer with solution. An analog signal with a bandwidth of 36MHz is sampled at a frequency (fs) of 72,000,000 samples per second during the ADC (analog-to-digital conversion) process. What is the outcome of the received signal after the DAC (digital-to-analog conversion) process? a. the signal will have experienced aliasing b. the signal will not experience aliasing c. the signal will not experience quantization errors d. none of the above describes the outcome
The following figure depicts a sampled analog signal for digital signal representation. By applying the concept of Pulse Code Modulation find the 4-bit code words and finally draw the line coding by using Bipolar-AMI scheme. You have to solve the problem by using step by step formulation of normalized PAM values, normalized quantized value, normalized error and quantization code. Assume that the sampling amplitudes are between -40V to +40V. Time Analog Signal Value (V) 23.7 1 -15.7 2 -29.6 3 20.5 33.5 4.
Draw the spectrum of the sampled signal when the sampling rate is equal to 2.5 × 10* d) Draw the spectrum of the sampled signal when the sampling rate is equal to 1× 104 Draw the spectrum of the sampled signal at the Nyquist rte. An analog signal given by: x() = stn'(104) %3D is sampled using an ideal sampling tchnique. a) What is the Nyquist rate of this signal. Samplesec. the samplekse,
b) The following figure shows a sampled signal and the desired sampled signal. A digital signal processing system is required to change the sampled signal to produce the desired output signal. 1 Desired output -1 0 1 2 3 4 5 Sampled signal -0.4 -0.3 i) Design the required digital signal processing system and provide the z-transfer function. Determine and comment on the system's stability.
ASAP
2. If the signal is 5 sin 200n t i. suppose the signal is sampled at rate of fs=300HZ, what is the discrete time signal obtained after sampling. ii. Find minimum frequency sampling to avoid aliasing. iii. Sketch the discrete time signal.
How to calculate the transfer function of this? How do we write the three non touching loops?
d. flatline 6. Continuous time signal sin (3m) is sampled at a rate of 4 samples per second. At what sample output value reach to peak value (+1V)? Hint. Simulate with sample index n = 0 to 20 samples. a. n=0 b. n 6 C. n 12 d. n= 4
[Q2] Illustrate the signal waveforms of PAM, PWM, and PPM in simple drawings. [Q3] Suppose (t) has the spectrum in the figure below, where f = 550kHz and € = 460kHz. Sketch Xs(f) for f. = 1.6MHz if ideal sampling is considered. X(f) AÏN -f f₁ + E 0 fu
Consider an analog-to-digital conversion (ADC) system with an ideal sampler, a uniform quantizer, and a binary encoder. The sampling rate is the same as the Nyquist sampling rate. The input signal to the uniform quantizer has an average power of 30 and an amplitude range of [-3,3]. The output signal-to-quantization-noise ratio (SQNR) of this uniform quantizer is 22.04 dB. The bit rate is 10 bits/second. What is the bandwidth of the input signal to this ADC system? 10 Hz 1.25 Hz 5 Hz 2.5 Hz
c) Draw the spectrum of the sampled signal when the sampling rate is equal to 2.5 x 10* An analog signal given by: x(t) = sinc?(10*t) is sampled using an ideal sampling technique. a) What is the Nyquist rate of this signal. b) Draw the spectrum of the sampled signal at the Nyquist rate. ) Draw the spectrum of the sampled signal when the sampling rate is equal to 1x 10 sample/sec. sample/sec.