For the crank- slide mechanism. B slides 03 along 0203 link making 300mm stroke, as shown in Figure.1. C is the first position B. b of the stroke. If S=133mm. 1. Determine: a S. C 30° a) The lengths of links a, and b. b) Find the imbalance angle c) Find the time ratio of the working 01 分02 250mm 133 stroke to return stroke. Figure.1

For the crank- slide mechanism. B slides 03 along 0203 link making 300mm stroke, as shown in Figure.1. C is the first position B. b of the stroke. If S=133mm. 1. Determine: a S. C 30° a) The lengths of links a, and b. b) Find the imbalance angle c) Find the time ratio of the working 01 分02 250mm 133 stroke to return stroke. Figure.1

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The figure below represents a Whitworth quick-return mechanism which is used in shapers. It is required that the tool holder (link 6) maintain a nearly constant velocity during the cutting stroke but accelerates on the return stroke in order to reduce idle time. The inputs are: VA2=8m/s, a2=0. Find the following: a) The angular velocity m4 b) The magnitude of the sliding velocity and acceleration of A c) Angular acceleration a4 d) Find the acceleration of A via link 2 e) Find the acceleration of A using the angular velocity and acceleration along with the Coriolis effect and the acceleration along the axis of slip (via link 4) f) Find the acceleration of the tool holder (C). 2 (VA2 = 6 m/sec 02 4 B * 45° 0,04 0,A = 19.1 cm 0,B = 10.2 cm 35.6 cm 8.9 cm 04 BC
Compute the position and orientation of the tool point P from the given D-H table for the displacement variable e1-90° e2-90° and e3=90⁰ a1= 100 mm, a2= 100mm and a3 = 50mm Note: find the position and orientation using step by step procedure Figure 3 3-DOF (Industrial manipulator arm) Joint 0 d 1 01 0 2 02 3 03 0 0 Present the roll, pitch, yaw and displacement in x, y and z axis. use the composite transformation matrix [ce; -se,Cα; se; SÔ i-¹T₁ = 0 0 Sα₁ 0 CÔ Ca; co,ca; a a1 a2 az s0;Sα; se a | -90 0 0 Cα₁ 0 a;C0₁] –CĐ Sa, : aS0; a¡SO; d; 1
6 solve 6 show complete STEP BY STEP solution, and draw a FBD.
Solve using parallelogram and Trigonometry please explain how
Find the value of the determinant D given by: a b 3 D = c d -4 6 9 9 where a = 2, b = 4, c = 9, d = 13 Give your answer as an integer.
The kinematic diagram is given as ?12 = 600 and the speed of the mechanism is constant and ?'-12 = 50 rad/second in the slide mechanism, the limb dimensions of which are given below. Find the following items. a) Write the vector closure equations. b) Put the vector closure equations in scalar form. c)Find ?13, ?14. d)Find s'13, ?14. e)Find s'', ?14.
Please solve step by step I will surely gives u upvote
Ex. Find 9 f- 120mm 125mm !30m
Q3 / Draw the following spring with all dimensions in sheet (write down all the equations you used in the :drawing if found) D1 70 mm D2 50 mm L 125 mm d 10 mm Pitch 25 mm
Choose the following and define also
Please solve 1,2,3,4,5 And show some steps how you drawn
a)Find the degrees of freedom. b)Draw the kinematic chain. Solve both