For the figure below, all dimensions in inch. A/The total Area:* /The value of Y-bar is: * the value of X-bar is: 0.364 1.5 0.987 25 3.309 2.5 2.309 0.65 2.5 2.5 0.587 0.398 12.6 0.254 4.32 14 0.5 3.105 25.93 13.5 0.487 1.3 14.68 0.55 3.623 13.68 0.857 31 1.06 22.5 Other: 2.5 24 12 Other: Other: 2. O O O O O O C

For the figure below, all dimensions in inch. A/The total Area:* /The value of Y-bar is: * the value of X-bar is: 0.364 1.5 0.987 25 3.309 2.5 2.309 0.65 2.5 2.5 0.587 0.398 12.6 0.254 4.32 14 0.5 3.105 25.93 13.5 0.487 1.3 14.68 0.55 3.623 13.68 0.857 31 1.06 22.5 Other: 2.5 24 12 Other: Other: 2. O O O O O O C

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter3: Job Planning, Benchwork, And Layout

Section3.1: Understanding Drawings

Problem 9RQ: A dimension listed on an engineering drawing is known as the _______ _______.

See similar textbooks

Similar questions

For the figure below, all dimensions in inch. A/The total Area : * y 3 1.5 2.5 2.5 2.5 2.5 O 25.93 О 13.68 14.68 O 24
Calculate the Minimum Y distance on the drawing below: 1.000 O 2.000 O .460 O .510 1.966 O .500 C 2.000 Ø.995-1.000 6.00 0.008 MABC 3.000 Y 01.005-1.030 +0.005MABC B A .XX = .01 ANGLES= ± 1°
Round off the numbers in the following problems to three significant figures. Find the percent difference between each rounded-off number and the original number by using the original number as the reference. 6471.9
A dimension listed on an engineering drawing is known as the _______ _______.
Select the correct statement about the notation circled in green and marked as letter B. Assume all dimensions are in inches. 4x375 A с 8.00 HOH 4x5.25 4x 4.75 4x R.70 4x 115.0 4x 1.40 B HOH 4x 2.00 - 4x 1.20 6.00 25 11 4x.75 4x.25 .75 1.00 6.50 SECTION A-A O SCALE 0.400
Calculate the Minimum Y distance on the drawing below: 1.000 O .500 1.966 O .460 O 2.000 O .510 C 2.000 Ø.995-1.000 6.00 0.008MABC X 3.000 01.005-1.030 +0.005MABC B A .XX = .01 ANGLES ± 1°
Type in your answer/s rounded off to 2 decimal places except for whole numbers. (ex: 10.67, 28, 732.40) If your answer is 120.00 kN, just write 120 kN Do not round off values during solving. Use the store function of your calculator or its fraction if applicable. Include the units after your answer. Leave a space between the value and the unit. (ex: 6323.17 m, 73.10 rad/s^2, 100 kN) For stresses, type (C) for compression and (T) for tension one space after the unit. (ex: 18.19 MPa (C), 6.88 psi (T))
Select the correct statement about the notation circled in green and marked as letter C. Assume all dimensions are in inches. 4x375 A с 8.00 Lo A- Hoy 4x5.25 4x 4.75 4x R.70 4x 115.0 4x 1.40 B 4x 2.00 4x 1.20 6.00 25 M₂ 4x.75 4x 25 .75 1.00 Ø6.50 SECTION A-A SCALE 0.400 4
Type your answer in the space provided after each item. Type in your answer/s rounded off to 2 decimal places except for whole numbers. (ex: 10.67, 28, 732.40) If your answer is 120.00 kN, just write 120 kN Do not round off values during solving. Use the store function of your calculator or its fraction if applicable. Include the units after your answer. Leave a space between the value and the unit. (ex: 6323.17 m, 73.10 rad/s^2, 100 kN, 12.90 mm^2, 120 lbs) There is no period after the unit.
Show all steps/ round off to 3 decimals/ use g=9.81m/s2
A shaft has to be assembled with a hole. The shaft has maximum limit 59.762 and minimum limit 59.56, and the hole has a maximum limit 60.24 and a minimum limit 60.04, compute the following: Tolerance of the shaft is Tolerance of the hole is Shaft size according to MMC = Shaft size according to LMC = Maximum clearance = Minimum clearance = Hole size according to MMC = Hole size according to LMC =
Figure shows the design of a taper turning operation performing on a lathe machine. D1 D2 d D3 L3 L2 L1 Find small diameter 'd" using the date to find the following SI. Parameter in Drawing Dimension in mm No: D1 65.5 D2 48.5 3. D3 33.5 4 L1 13 L2 7.5 L3 11 7 Small diameter 'd (in mm) =