For the network in Fig. below, the complex power absorbed by the source on the right is 0 + j1582.5 VA. Find the value of R and the unknown element and its value if f = 60 Hz. (If the element is a capacitor, give its capacitance; if the element is an inductor, give its inductance.) ww R Unknown element +120/-10° V rms 150/0° V rms

For the network in Fig. below, the complex power absorbed by the source on the right is 0 + j1582.5 VA. Find the value of R and the unknown element and its value if f = 60 Hz. (If the element is a capacitor, give its capacitance; if the element is an inductor, give its inductance.) ww R Unknown element +120/-10° V rms 150/0° V rms

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.27P: An industrial load consisting of a bank of induction motors consumes 50 kW at a power factor of 0.8...

See similar textbooks

Similar questions

An industrial load consisting of a bank of induction motors consumes 50 kW at a power factor of 0.8 lagging from a 220-V,60-Hz, single-phase source. By placing a bank of capacitors in parallel with the load, the resultant power factor is to be raised to 0.95 lagging. Find the net capacitance of the capacitor bank in F that is required.
Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
. Given: An inductive load draws an apparent power of 5 kVA at a lagging power factor of 0.75. The load voltage is 1.2 KVRMS at 60 Hz. A 5-uF capacitor is connected in parallel to the load. Find: What is the new power factor of the system? -. Given: You have a complex inductive load that is dropping 240 VRMS. The operating frequency is 60 Hz. The current in the load is 9.615 ARMS. The load is dissipating 1.5 kW of average power. Find: Determine the value of a capacitor to attach in parallel with the load to change the load such that its power factor is 1.0.
A chopper circuit has an inductive load of 2ohm resistance and 10mH inductance. If the source voltage is 20 V and the frequency of the chopper is set to 100Hz and the on-time to 5 ms. Determine the average voltage and current, maximum and minimum load currents.
A sinusoidal 50 Hz voltage of 200 V (rms) supplies the following three circuits which are in parallel: (a) a coil of inductance 0.03 H and resistance of 3 ohms, (b) a capacitor of 400 microFarad in series witha resistance of 100 ohms and (c) a coil of inductance 0.02 H and resistance 7 ohms in series with a 300 microFarad capacitor. Find the total current supplied?
in the figure below, find a) The p.d across j5 ohmn inductance b)The p.d across -j10 ohmn capacitance c) the current in 20 ohmn resitance d) the current in (12+j160 ohmn impedance e) the complex power for (12+j16) ohmn impedance
Given a capacitive load absorbing 5 kW with a power factor of 0.85. The source connected to this load is an AC voltage supply with 120V RMS at a frequency of 50 Hz. Please find; A) Peak current (m) and RMS Current (ms) Values B) Draw peak voltage and current phasors on phasor diagram with everything labelled C) Find the value of an inductor that when connected in parallel will improve the power factor to 0.95.
1. What is the shortest time required for a 4.3-krad/s sinusoid to increase from two-fifths to four-fifths of its peak value ? CHOICES: A. 120 s B. 140 s C. 160 s D. 180 s E. NOTA
An electrical circuit with a sinusoidal voltage source, a resistor, and a capacitor all connected in series. The voltage across the capacitor: Select one: a. Leads the current in the capacitor by exactly 90o b. Is in phase with the sinusoidal voltage source c. Is in phase with the voltage across the resistor d. Leads the current in the circuit by 90o e. Lags the current in the circuit by 90o
What impedance vector (0- j15) Ohms represents:A. A pure resistance. C. A pure capacitance.B. A pure inductance. D. An inductance combined with a capacitance.
A voltage vz(t) = 10 cos(2000zt) is applied to a 100-mH inductance. Find the complex impedance of the inductance. Find the phasor voltage and current, and construct a phasor diagram. Write the current as a function of time. Sketch the voltage and current to scale versus time. State the phase relationship between the current and voltage.
A capacitor C is connected in series with a 400 resistor across a supply of frequency 60 Hz. A current of 3 A flows and the circuit impedance is 500. Calculate: (a) the value of capacitance, C, (b) the supply voltage, (c) the phase angle between the supply voltage and current, (d) the p.d. across the resistor, and (e) the p.d. across the capacitor. Draw the Phasor diagram.