For the system shown in figure Q5. а. Determine the three-phase fault power (in MVA) and the short circuit current (in kA) for a three- phase fault on busbar A. b. How could the fault power to both parts of busbar A be reduced without additional capital expenditure? С. For your chosen arrangement what would the new level of three-phase fault power be at busbar A? T2

For the system shown in figure Q5. а. Determine the three-phase fault power (in MVA) and the short circuit current (in kA) for a three- phase fault on busbar A. b. How could the fault power to both parts of busbar A be reduced without additional capital expenditure? С. For your chosen arrangement what would the new level of three-phase fault power be at busbar A? T2

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter7: Symmetrical Faults

Section: Chapter Questions

Problem 7.15P

See similar textbooks

Similar questions

b) The one-line diagram for a simple power system is given in Figure 1(b). į. Draw the impedance diagram of the system. i. Construct the bus admittance matrix, Xeus and bus impedance matrix, Zous of the system. I. Evaluate the fault current, bus voltages and line current during the flow when a balanced three-phase fault occurs on bus 1. bus 1 bus 2 j65 N G G 25 MVA 25 MVA 13.8 kV 15% 13.2/69 kV 11% 25 MVA 69/13.2 kV 11% 15 MVA 13 kV 15% Figure 1(b) m
For the circuit shown, if a symmetrical three-phase fault occurs in node 2, determinea. The short-circuit current in all three phases. b. The voltage at node 1 during the fault.c. The current in generator 1 during the fault. Neglect the prefault currents and consider the reference voltage of the system at 10√3 ??.
b) A fault occurs at bus 2 of the network shown in Figure Q3. Pre-fault nodal voltages throughout the network are of 1 p.u. and the impedance of the electric arc is neglected. Sequence impedance parameters of the generator, transmission lines, and transformer are given in Figure Q3, where X and Y are the last two digits of your student number. JX20 /0.1X p.u. jXa2) 0.1X p.u. JX20 j0.2Y p.u. V,= 120° p.u. V, 120° p.u. V, 120° p.u. jX4-70.2X p.u. jX2 j0.2X p.u. jX o 0.2Y p.u. jXncay J0.25 p.u. jXna J0.25 p.u. 3 jXno0.3 p.u. jXTu) /0.2Y p.u. jXra j0.2Y p.u. - j0.2Y p.u. Xp-10.1X p.u. jXa j0.1X p.u. jXp0)- j0.05 p.u. 0 Figure Q3. Circuit for problem 3b). For example, if your student number is c1700123, then: jXac1) = j0.22 p.u., jXac2) = j0.22 p.u., and jXaco) = j0.23 p. u. X-2 Y=8 (iv) Determine the short-circuit fault current for the case when a phase-to- phase fault occurs at bus 2.
Description In the particular case of figure below derive both the critical clearing angle and the critical clearing time. P, = Pmaz sin d Pm A1 do der Smar A generator having H = 6.R MJ/MVA is delivering power of 1.0 per unit to an infinite bus through a purely reactive network when the occurrence of a fault reduces the generator output power to zero. The maximum power that could be delivered is 2.5S per unit. When the fault is cleared, the original network conditions again exist. Determine the critical clearing angle and critical clearing time. (Roll=PQRS)
Three 15MVA, 30kV synchronous generators A, B, and C are connected via three reactors to a common bus bar, as shown in Figure below. The neutrals of generators A and B are solidly grounded, and the neutral of generator C is grounded through a reactor of 2. Q. The generator data and the reactance of the reactors are tabulated below. A line-to-ground fault occurs on phase a of the common bus bar. Neglect prefault currents and assume generators are operating at their rated voltage. Determine the fault current in phase a. GB Gc Item GA GB Gc 0.25 pu 0.155 pu 0.056 pu 0.20 pu 0.155 pu 0.056 pu 0.20 pu 0.155 pu 0.060 pu 6.0 ? REACTOR Reactor 6.0 6.0
5.26 An unloaded generator with a pre-fault voltage ct 1 pu has the following sequence impedance: Z, = j0. 15 pu, Z, = Z, = j0.25 pu The neutral is grounded with a reactance of 0.05 pu. The fault current in pu for a single-line to ground fault is (a) 3.75 pu (c) 6 pu (b) 4.28 pu (d) 7.25 pu
The chances of faults in underground system are as compared to overhead system .... O less more above none
The zero sequence current of a generator for line to ground faults is j 3.0 p.u. Then the current through the neutral during the fault is
5.10 The zero sequence current of a generator for line to ground fault is j2.4 p.u. Then the current through the neutral during the fault is (a) j2.4 p.u. (b) j0.8 p.u. (c) j7.2 p.u. (d) j0.24 p.u.
Let the system of Figure 1 operating with mechanical input Pm at a steady angle ôo. A three phase fault occurs at the outgoing radial line and hereby the fault is cleared by opening the circuit breaker. Now, find the effect of clearing time on transient stability. Breaker Generator G XL Transformer Fault Pm
Three zones of a single-phase circuit are identified in Figure. The zones are connected bytransformers T1 and T2, whose ratings are also shown.Using base values of 30 kVA and 240 volts in zone 1:a. draw the per-unit circuit and determine the per-unit impedances and the per-unitsource voltage.b. calculate the load current both in per-unit and in amperes. Transformer windingresistances and shunt admittance branches are neglected.
Q3: - A three-phase fault occurs at bus-1 of the network shown in figure below. The pre-fault voltage is 1.05 PU and the pre-fault load current is neglected. (45%) i) determine the bus impedance matrix. ii) calculate the sub-transient fault current and the contribution to the fault current from the transmission line. T1 T2 T.L j0.1 PU 10.1 PU j0.105 PU G jXdg j0.15 PU M jXdm $0.2 PU