For the truss loaded as shown, determine the equation for the line of action of the stand-alone resultant R and state the coordinates of the points on the x- and y-axes through which the line of action passes. All triangles are 3-4-5. Assume F₁ = 25 KN, F₂ = 30 kN, F3 = 35 KN, F4 = 25 KN, and M = 105 kN-m. A 6 m H C Answers: x-axis: x= 8 m Equation of line: y = 1 y-axis: y = 1 F₂ B с M D E m X+ m

For the truss loaded as shown, determine the equation for the line of action of the stand-alone resultant R and state the coordinates of the points on the x- and y-axes through which the line of action passes. All triangles are 3-4-5. Assume F₁ = 25 KN, F₂ = 30 kN, F3 = 35 KN, F4 = 25 KN, and M = 105 kN-m. A 6 m H C Answers: x-axis: x= 8 m Equation of line: y = 1 y-axis: y = 1 F₂ B с M D E m X+ m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3. The magnitude of the force P applied is necessary to cause impending motion of the 40- block up the slope in the figure below. The coefficient of static friction of all contact surfaces 0.10. (a) (a) Draw the FBD of the block. Show all the necessary angles of inclined forces. ( Draw the triangle that will solve for the force exerted by the bar on the block at B. Indicate a the angles in the triangle. (Note: there is nothing to solve, you will only draw what is being aske in (a) and (b). 40 lb B 30 P. 5' 2' 3'
Q: A horizontal beam AB is simply supported. at A and B, 8m apart. th beam is subjected to counter-clokwise couple of 4oo kn.m at distance of 3m from the left end as shown in figure blow. the value of I for the right half (A-B) is (1X10 mm") and for th lef half (B3-c) Portion 21 is (2×108 mm²) and E = 2X10 N/mm². determine! (i) deflection at the point where couple is acting and (ii) the slope at the ends and ta Point C. A 2 I .5m 400 kn. m 8m с I B
Problem I. The beam has a loose fit built-in support at B which allows the end of the beam to rotate through the angle e, = 0.75° when the load is applied, as shown in the detail. E = 72 GPa and |= 120 x 10°mm*. Determine the following: a. Reaction at A (kN) | 200 kN -2 m 2 m b. Moment at B (kN m) c. Slope at A in radians В d. Displacement at the application of 200kN load Detail
Asap
The rigid bar ABC supports a point load P at point A and is being supported by bronze bars BD & CE. For bronze, E = 83 GPa. Determine 4 m 2 m A the maximum allowable load P if the vertical deflection of point A is limited to 1 mm. The areas of bars BD and CE are 1020 mm? and 520 mm?, respectively. 3 m P 3.5 m Assume no bending for all bars. D А. РМАХ (N)
The force-couple system shown acts on atrapezoidal plate. a. Determine thevalue of M, if the system shown is equivalent to a single force acting at point C. b. The system shown is equivalent to a force couple system consisting of R and M2= 3000 kip-in clockwise. If M, in this case is 120 kip-in counterclockwise, determine the point of action of the resultant force R along line CD. 50° 1YZ kips 10 in 1X in 10 in 20 kips 35 kips 8x kips 2Y in 5o 1YZ kips Parameters X = 7, Y = 3, Z = 7 1X in 17 in 23 in 87 kips 137 kips 2Y in 8x kips 1YZ kips 18 in
HW 2 A cable is attached to the plate B of weight W, passes over a fixed peg at ingsand is attached to the block at A. U hown,sthe coefficients of static friction determine the smallest mass of block A so that it will prevent sliding motion of B .down the plane H 0.3 B 30
Q3] For the given beam, neglecting self weight, find: (1) The equation of the deflection curve. (2) The maximum deflection. (3) The bending moment at the fixed end. (4) The value of the expression: EI.D'y-P.D²y. lle L=3 m EI-6000 kN.m² W=120 kN P=60 kN
plz solve it in slope deflection !! Determine the reactions at the supports. Assume A is fixed connected. E is constant SAN/m LAn-1250 (10') mm* 3 m 20 kN Inc 625 (10) mm
4. DETERMINE THE MOMENT OF THE FORCE F AT THE END OF THE ANGLE BRACKET ABOUT POINT O. THE VALUE OF F IS 800N. -0.4 m FIGURE 4 0.2 m 300 4
An equilateral triangular truss ABC has a vertical member AC that has one of its side 2m long. It has a roller support at A and hinged at C. The truss carries a vertical load of 50 kN at joint B. Cross- sectional area of all members is 800 mm² and E=200,000 MPa. Compute the horizontal deflection at B. 2m 60 2m 60 B 50 kN 60 2m Select one: O a. 2.42 mm O b. 0.37 mm O c. 1.06 mm O d. 0.09 mm
Solve using Moment -Area Method. The beam has a loose fit built-in support at B which allows the end of the beam to rotate through the angle e, = 0.75° when the load is applied, as shown in the detail. E= 72 GPa and I = 120 x 10°mm“. Determine the following: a. Reaction at A (kN) b. Moment at B (kN m) |200 kN 2 m 2 m c. Slope at A in radians d. Displacement at the application of 200kN load B Detail