For this long shoe break system, we adopt the hard surface assumption with the maximum pressure of the lining equal to 0.7 MPa and friction coefficient is 0.25. The width of the lining is 50 mm. Find the torque exerted on the brake about center of rotation A induced by both the normal force due to the lining pressure and the tangential force due to the friction? Rotation 38 → ww t 125 mm 90° 15d 88 mm 88 mm P

For this long shoe break system, we adopt the hard surface assumption with the maximum pressure of the lining equal to 0.7 MPa and friction coefficient is 0.25. The width of the lining is 50 mm. Find the torque exerted on the brake about center of rotation A induced by both the normal force due to the lining pressure and the tangential force due to the friction? Rotation 38 → ww t 125 mm 90° 15d 88 mm 88 mm P

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The width of the simple band brake shown in the figure is 30 mm. The coefficient of friction between the brake and the drum surface is 0.20. Determine the braking torque and thickness of the band if the tensile stress is not to exceed 65 N/mm2.
50 mm and the coefficient of friction between the blocks and the drum is 0.25. 30° Q9/ braking system has its braking lever inclined at an angle of 30° to the horizontal plane, as shown in Figure. The diameter of the brake drum is 540 mm and rotates clockwise; the angle of contact surface of the block is 50. At the instant the lever is pressed on the brake drum with a vertical force of 600 N. The coefficient of friction between the brake shoe and the brake drum is 0.4. Assume that the lever and brake shoe are perfectly rigid Brake drum- and possess negligible weight. Find the braking torque. -0.4 m- Horizontal plane 0.8 m 600 N
A conical friction clutch is used to transmit 70 kW at 1000 rpm. The semicone angle is 20° and the coefficient of friction is 0.2. If the outer diameter is 400 mm and the inner diameter is 340 mm and the intensity of normal pressure is not to exceed 0.20 N/mm². Determine the axial Force (F) required in Newton (N)
The hand brake of Fig. is used to control the rotation of a drum. The coefficient of friction between the belt and the drum is , = 0.15, and the weight of the handle may be neglected. If a counterclockwise torque of 5 ft - Ib is applied to the drum Repeat the problem for a clockwise torque of 5 ft · Ib. What happens to the system at a 4.6 in.? What does the solution mean for a> 4.6 in.? M= 5 lb-ft -12 in. 12 in
A car engine has its rated output of 120 kW. The maxdmum torque developed is 110 Nm, The clutch used is of single plate type having two active surfaces. Axia! pressure is not to exceed 0.85 bar. External diamater of friction plate is 1.25 times the internal diameter. Determine the dimensions of friction plate and axial force exerted by the spring. Assume uniform wear and coefficient of friction to be 0.3.
Q5: The block brake, as shown, provides a braking torque of 360 N.m The diameter of the brake drum is 300 mm. The coefficient of friction is 0.3. Find 1. the force (P) to be applied at the end of the lever for the clockwise and counter clockwise rotation of the brake drum, and 2. The location of the pivot or fulcrum to make the brake self-locking for the clockwise rotation of the brake dracs 100 10 ( F₁ 4 μ sin 80 20+ sin20 T = (F₁) r Bearing Area A, b(2r sind) RN = (1 20 R 600 Brake drum
5 The forces F, and F, in a brake band and the direction of rotation of the drum are as shown in the figure. The coefficient of friction is 0.25. The angle of wrap is 3Tt/2 radians. It is given that R = 1 m and F, = 1 N. The torque (in Nm) %3D %3D exerted on the drum is F2 F,
The axial pressure on a single disc clutch (both sides of the disc is effective) is limited to 0.12 Mpa. This is designed for a vehicle with 13kW power at a speed of 700 rpm. Assume uniform wear conditions and a friction coefficient of 0.25. If the outer dimater of the disc is 1.25 times the internal diameter, determine the dimensions of the disc lining and the axial force exerted by the springs.
A band brake is installed on a drum rotating at 250 rpm, and a diameter of 900 mm. The angle of contact is 1.5 pi radians and one end of the brake band is fastened to a fixed pin while the other end of the brake arm is 150 mm from the fixed pin. The coefficient of friction is 0.25 and the straight brake arm is 1000 mm long and is placed perpendicular to the diameter bisecting the angle of contact. Determine the net band pull in kN applied at the end of the brake arm if 50 kW is being absorbed.
A calliper brake is required for the front wheels of a sport's car with a braking capacity of 890,485 Nm for each brake. Preliminary design estimates have set the brake geometry as r=100 mm, ro=155 mm and 0=45°. A pad with a coefficient of friction of 0,45 has been selected. Determine: 4.1. the required actuating forces, 4.2. the average and maximum contact pressures.
A band brake embraces a 500 mm diameter drum with an angle of lap of 270° and produces a braking torque of 200 Nm. The coefficient of friction is 0.2. One end of the band is attached to the fulcrum pin and the other end is attached to a pin B. Which of the following is the tension in the slack side of the band? 75 -450 C 270° O 280 N O 510N O 255 N 0 445 N All dimensions in mm.
A cone clutch is mounted on a shaft which transmits power at 200 rpm. The small diameter of the cone is 200 mm, the cone face is 50 mm and the cone face makes an angle of 12 degrees with the horizontal. Determine the axial force necessary to engage the clutch to transmit 7 kW if the coefficient of friction of the contact surfaces is 0.15. What is the maximum pressure on the contact surfaces assuming uniform wear?