Form the figure below, the power transmission shaft shows the forces acting on it carrying two gears. The gears are keyed at B and D. A and C are journal bearing centers. Ten hp is transmitted at 750 rpm of the shaft. Assume allowable stress for an unkeyed section equal to 12,000 psi and use Km=K¡ = 2.0. What is the approximate shaft diameter in inches?

Form the figure below, the power transmission shaft shows the forces acting on it carrying two gears. The gears are keyed at B and D. A and C are journal bearing centers. Ten hp is transmitted at 750 rpm of the shaft. Assume allowable stress for an unkeyed section equal to 12,000 psi and use Km=K¡ = 2.0. What is the approximate shaft diameter in inches?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Assignent no 1 Qt+ A Compound gear 6 Jears. No of teeth; train Consists of A B D 60 40 35 २४ 50 30 shaft on another shaft. The Gears B ş C are on one while are gears Gear A drives c drives gear D B, gear gear S gear E drives gear F. Gear A transmits 1.5 Kw at 15orpm Find speed of Gear F ? Q2+ State advatages of Cycloidal In volute profile as a gear tooth pnfile.
1) A pair of cast iron bevel gears connect two shafts at right angles. The pitch diameters of the pinion and gear are 80 mm and 100 mm respectively. The tooth profiles of the gears are of 14 1/2° composite form. The allowable static stress for both the gears is 55 MPa. If the pinion transmits 2.75 kW at 1100 r.p.m., find the module and number of teeth on each gear from the standpoint of strength and check the design from the standpoint of wear. Take surface endurance limit as 630 MPa and modulus of elasticity for cast iron as 84 kN/mm2.
1) A pair of cast iron bevel gears connect two shafts at right angles. The pitch diameters of the pinion and gear are 80 mm and 100 mm respectively. The tooth profiles of the gears are of 14 1/2° composite form. The allowable static stress for both the gears is 55 MPa. If the pinion transmits 2.75 kW at 1100 r.p.m., find the module and number of teeth on each gear from the standpoint of strength and check the design from the standpoint of wear. Take surface endurance limit as 630 MPa and modulus of elasticity for cast iron as 84 kN/mm². A0a& ENG 1222/20 nere to search
A train of spur gears is shown in the 2 points Figure below. Gear 1 is the driving gear. The pitch circular diameters of gears 1, 2, 3 and 4 are 100, 400, 100 and 400 respectively. The module for all gears is 4 mm. The gears have a 20° full-depth involute profile. The ratio factor Q for these gears is. Output shaft 3 Input shaft 1.341 1.6 1.5 1.42 2.
In the figure below the gears are 20º full depth of AGMA Quality No 8. a) Find the horsepower transmitted by the 1-2 mesh b) Find the required width b for the 3-4 mesh if they are carrying the same horsepower as the 1-2 mesh. No.2, C.I. BHN=220 P=4, N₂=72,b=2" No 1, Steel, P=4, N₁=24,b=2" n₁ = 570 rpm /No.4.CI. BHN=220 P=3, N₂=72 No.3, Steel, P=3, N₁=24
You have been asked by your engineering company to design a complete gear and shaft system shaft that is made of steel. The solid shaft is linked with gear A, B. C and D with gear A., B and C produces torque of 15 kNm (clockwise), 30 kNm (clockwise) and 75kNm (anticlockwise). respectively each. If AB = 0.70m, BC= 0.80 m and CD=0.90 m with the shafts consist of solid circular shafts with a diameter of 150 mm having the shear modulus of G = 80 GPa, b) The shafts are now to be redesigned by drilling only through shaft BC with a diameter hole, cz to produce a hollow shaft BC. It is also known that the allowable shear stress, Tall in the shaft must not exceed 85 MPa. i) Determine the minimum wall thickness of the shaft BC, tBc
NEED DETAILED ANSWER ASAP, THANK YOU The four rigid gears, loaded as shown in the figure, are attached to a 2.89-in.-diameter steel shaft. Compute the angle of rotation of gear A relative to gear D if TA = 414 lbft, TB = 911 lbft, and TC = 1156 lbft. Use G = 12041783 psi for the shaft. Round off the final answer to four decimal places.
A gear train with a ratio of -6:1 and a diametral pitch of 8 is used to reduce the speed from an electric motor to a shaft driving a grocery checkout conveyor. Grocery checkout conveyor Electric motor @, = 1800 rpm a. If the motor rotates at 1800 rpm clockwise, determine the speed and direction of the large gear. b. For a pressure angle of 20 deg, determine the minimum number of teeth for the pinion. Assume the gears are cut by a shaper (NOT a hob). c. Specify pitch diameters and numbers of teeth for the pinion and the gear for the most compact gear train.
Calculate the smallest allowable diameter of the AD shaft as τem = 60MPa in the gear shaft system in the figure.
three spur gear arrangement are shown. it has a pinion gear A-driver that rotates for about 500 rpm. the second gear, gear B- an idler and the third gear, gear C- driven gear. the three gears have a diametral pitch of 5 and power of 10hp. The pressure angle is 20°.Number of teeth are shown in the figure. determine the following: i) The pitch diameters of each of the gears. ii) The torque that each shaft is required to transmit. iii) The forces on each of the gears, shown on a free body diagram. iv) The resultant force on the shaft carrying Gear B.
For a pair of standard gears, the module is m=2.5mm，pressure angle is α=20 0. ha*=1. c*=0.25. The teeth number on gear 1 is z1=22. The standard center distance is a=68.75mm. If the actual center distance is a’=69.75mm, find the working pressure angle α’=( )°
The teeth of the gear arrangement have Gear A=40teeth, Gear B=70 teeth and Gear C= 50teeth, a pinion (driver Gear) that rotates at 625 rpm, and idler Gear B and a driven gear (Gear C). The gears have a module of 5mm and a pressure angle of 200. Find the pitch diameter of gear C in mm.