Formulate the linear program on the following problems: The Central City Manufacturing Company produces two types of toy model cars, the standby streamer and the model T. Three machines are required to produce each type; these machines are classified as MC1, MC2, and MC3. Each standby streamer requires seven (7) minutes process time on MC1, four (4) minutes on MC2 and 10 minutes on MC3, A model T requires four (4)minutes on MC1, 15 minutes on MC2, and 16 minutes on MC3. Each day there are 420 minutes of available time on MC1, 600 minutes on MC2 and 840 minutes on MC3. The var- iable cost is P50 per unit of standby streamers and P64 per unit for the model T. Standby streamers sell at a price of P58 per model, whereas model T's sell for P7 per model. The company's fixed cost is P70 per day. Using the graphical method, determine the daily production rate for the two models which will maximize profit. 1.

Formulate the linear program on the following problems: The Central City Manufacturing Company produces two types of toy model cars, the standby streamer and the model T. Three machines are required to produce each type; these machines are classified as MC1, MC2, and MC3. Each standby streamer requires seven (7) minutes process time on MC1, four (4) minutes on MC2 and 10 minutes on MC3, A model T requires four (4)minutes on MC1, 15 minutes on MC2, and 16 minutes on MC3. Each day there are 420 minutes of available time on MC1, 600 minutes on MC2 and 840 minutes on MC3. The var- iable cost is P50 per unit of standby streamers and P64 per unit for the model T. Standby streamers sell at a price of P58 per model, whereas model T's sell for P7 per model. The company's fixed cost is P70 per day. Using the graphical method, determine the daily production rate for the two models which will maximize profit. 1.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

David is working on her farming business and faces the challenge of watering her plants daily,which is a tedious and time-consuming task, especially under the scorching sun. The path shefollows for watering the plants is illustrated in figure 1.David's son has taken on the task of designing a prototype to automate the watering process forher. Figure 2 depicts the design, featuring a set of rods. The curved path represents David'stypical watering route, and the straight rod AB AB is confined to move along the path due to the pinsat its ends. Water sprinklers will be positioned at points A and B to efficiently water the plants.At the instant shown in figure 2, point A has the motion shown while its at the edge of the path.Determine the velocity and acceleration of point B at this instant.
Command: PLOTTERMANAGER (from the autocad file m TO CONFIGURE A LOCAL, NONSYSTEM PLOTTER 10. PROFILES-Controls the use of profiles. A profile is a configuration you define. 367N 367N R=1.0m 426N 426N B. 426N C. The two identical sphemes having oqual weights of 367N is placed on top of the three identic al sphere's w/ 426 N as their reight . Compute the reaction A,B and C
An engineer camping in the woods, while scoping out a new development project, wants to boil an egg for exactly nine minutes. The only timing devices available are a four-minute sandglass, and a seven-minute sandglass. After some thought, the engineer figures out a way to use the sandglasses to time the nine-minute egg. What is the process? Note that the engineer is not allowed to break either sandglass, or otherwise manipulate them.
I need to find the command and plot on Matlab.
3. As a robotic engineer, your boss needs you to move the gripper on the UGV to the target object. The workspace is shown Figure 1. In order to finish the task, you need to find the correct representation. {b} {c} {e} {s} {d} Figure 1 The Workspace The fixed frame is {s}, a body frame {b} is attached to the chassis of the UGV, a body frame {c} is attached to the gripper, a body frame {d} is attached to the sensor, and a body frame {e} is attached to the target object. The sensor's location is known as Tsd, the chassis of the UGV's location is known as Tsb, the gripper's location's is Tsc, and the target object's location is Tse. The sensor can detect the target object, so the target object can be represented in the sensor's frame. The configuration of the UGV is reported simultaneously, and the gripper's configuration is also known. How to represent the target object in the gripper's frame?
Version #2 Describe the situation using a diagram: Contact Push/Pull Interaction 4 Write the narrative: During the contact push/pull interaction between the hand and the cart kinetic energy is transferred between them. The type of energy that changes in the two interacting objects is always the same as the type of energy that is transferred, so this means that the kinetic energy of the hand decreases while the kinetic energy of the cart increases. Since the cart was at rest to start with, this increase of kinetic energy means that it starts to move. Which criterion (accuracy, completeness, or clarity and logical reasoning) is not satisfied by this explanation? Briefly explain why you think so.
please send handwritten solution Q4 part c
(a) Summarize the following G and M code a. G41, G81, 691, G01, GOO b. M08, M30, M01, M06, M03 (b) Document three phases of writing a CNC program in the form of a block diagram. You don't have to write the actual CNC program.
Q4: Create a Visual Basic Project to find the value of the following series: h? h4 h3 cos(h) = h – 2! 3! 4! Write the code program so that the value of angle (h) is entered into inputbox. Estimate the value of series (cos(h)) so that the absolute value of any term is greater or equal to 10-6. Display the required number of terms (N) which it used in this series in a text box and display the result of series (cos(h)) in another separate text box.
hi ive have nearly completed this model but i am stuck on a couple last parts. Firstly, the holes on the top need to be placed 30 degrees from the y axis as shown in the handout but also the middle part is meant to have triangular "supports" rather than rectangular and im not sure how to cut them down. This is in autodesk inventor but any help here would be appreciated Once again just the top holes being moved 30 degrees and the support being cut down to the triangular shape shown in the handout
please send handwritten solution Q4 part d
Q2. Using a graph paper, draw a quick return mechanism that has time ratio between return and forward of 3:8.