Answered: Gate AB in Fig. of pressure. is 1.0 m…

Gate AB in Fig. of pressure. is 1.0 m long and 0.9 m wide. Calculate force F on the gate and the position X of its center 7m -8m Oil, 5.g.=0.81 3m 10m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Determine the flowing bottomhole pressure required for a well completed with 3.5 inches tubing set…

A: Given Depth, h = 12500 ft = 3810 m Pressure, P1 = 125 psig…

Q: Problems 10-16 Information: Jose' pushes a wheelbarrow consisting of a wheel (mass mw = 3 kg, radius…

A: We can answer up to 3 sub-parts so we will answer first 3 sub-parts for you. Please resubmit the…

Q: Q1/Determine the corrosion rate of carbon steel in salt solution from the following laboratory data.…

Q: 1. When an airplane touches down at t = 0, a stationary wheel is subjected to a constant angu- lar…

Q: A lightly loaded full journal bearing has journal diameter of 25 mm, bush bore of 25.05 mm and bush…

Q: 3. A=X

A: As per the request I am solving part 3 .

Q: Q.6. A plate 450 mm x 150 mm has been placed longitudinally in a stream of crude oil (Sp. gravity…

Q: In reference to the figure below, if uk = 0.7 at the rear drive wheels B of the 1550 lb race car…

Q: The 3.0-kg collar is released from rest at A and slides down the inclined fixed rod in the vertical…

A: Answer: v = 2.333 m/s x = 71.52 mm

Q: A particle which moves with curvilinear motion has coordinates in millimeters which vary with the…

Q: Castor oil at 36 °C flows over a 6 m long and 1 m wide heated plate at 0.06 m/s. For a surface…

A: Given: The temperature of castor oil, To = 36 C The length of plate, L = 6 m The width of plate, b =…

Q: 1. An ideal Brayton Cycle has air at 100kPc and 25C entering the compresse After the heating…

Q: 1. A Rankine cycle works with a condenser pressure of 20kPa and a boiler pressure of 4000kPa. The…

Q: Q1): Determine the general solution of the O.D.E: (1-x) y'-y² =0

Q: The basic components of :any car are The Chassis. The Engine. The Transmission System. The Body. O…

A: To find : basic components of any car

Q: In reference to the figure, @ 1 ft Given: v = 8 ft/s w = 2 rad/s Determine the velocity in ft/s of…

A: Write the given data. v=8 ft/sω=2 rad/sr=1 ft

Q: The length of a pipe is 1 km and its diameter is 20 cm. If the diameter of an equivalent pipe is 40…

A: Given:1. l=1 km d=20 cmde=40 cm

Q: 1.10 Determine the maximum wavelength that hydrogen in its ground state can absorb. What would be…

A: given : element - Hydrogen

Q: A manufacturer is carrying out a vehicle performance analysis and subjects to a road test. The…

Q: A boundary layer is flowing on a flat plate where the freestream velocity is 24 m/s, and the…

A: Solution: Given Data: U∞=24 m/sv=1.5×10-5 m2/sf=95 HzF=2πfvU∞2

Q: A closed system consists of a fixed amount of mass and mass may cross the system boundary.

Q: The 61-lb crate slides down the curved path in the vertical plane. If the crate has a velocity of…

Q: Adiabatic process takes place so fast that there is no time for heat to be transferred. True O False

A: Concept: 1.Adiabatic process is an thermodynamic process during which heat transfer is zero. 2.This…

Q: The Simple Pendulum A. H M Sketch a graph to show the predicted relationship. 22 H Task 8 In your…

A: Given data: Initial pendulum height = H Acceleration due to gravity = 9.79 ± 0.05 m/s² We have to…

Q: Piston rings are lubricated by pressurized oil. O grease. diesel fuel. splashing oil. O gasoline…

A: Option (d): Splashing Oil

Q: Determine power

A: Given data; A lightly loaded full journal bearing has, Journal dia,D= 25 mmBush bore, b= 25.05…

Q: If a vessel containing liquid moves downward with a constant acceleration equal to 'g' then none of…

A: In this problem, it is asking what will happen when a vessel containing liquid moves downward with a…

Q: Rigid beam AB is supported by three bolts at A and a pin at B. The bolts at A are in double shear…

Q: Show in Figure 1 is the water flow system. The velocity head difference is v²₁-v²₂. -= 2.0m. Volume…

A: Given data V12-V222g=2m Q=0.5m3/s h1=1m…

Q: For the connection shown, the average shear stress in the 17-mm-diameter bolts must be limited to…

Q: Show in Figure 1 is the water flow system. The velocity head difference is . Volume flow rate is .…

Q: given actual Rankine Cycle, the actual turbine work serves as the input in determining the…

Q: 1. A copper wire with a resistance of 12.8 m2 has a cross-sectional area of 1.15 x 100 m². Find the…

Q: Glass has density of 3.1 Mg/ m³, specific heat of 0.88 j/g.k, fracture strength of 300 Mpa,elastic…

Q: figure below, if = 0.2 supplied to all four wheels of the 1.5 Ma vehicle with the mass center at G…

A: Given:μs=0.2m=1.5 Mg

Q: gravity 0 Qat tok

Q: В VB 15° 3 ft VA=5 ft/s A

Q: In reference to the figure, A 0.125 m 0.175 m B Vo = 10 m/s vo INR 30° Determine the velocity in m/s…

Q: Q1/Determine the corrosion rate of carbon steel in salt solution from the following laboratory data.…

A: Given data: Density (ρcs) = 7.86 g/cm3 Area, A = 24.96 cm2 K = 3.45×10-6

Q: Problem 1: For the crank in the figure below and loaded as shown, determine the location of maximum…

Q: Select correct formula and description of the mechanical efficiency for fluid motorse M, motor Power…

Q: ! The most important systems in automatic gear boxes are O universal joint and ball bearing system.…

Q: A B Given: AB= 10.5 m BC = 8.2 m 0 = 41° ß = 28° Determine the angular velocity in rad/s of link AB…

Q: The standard Brayton air cycle has a compressor pressure ratio of 10. Air entering the compressor at…

A: Write the given data. P2P1=10P1=14.7 lbf/in2T1=70 °F=529.67 °Rm˙=90000 lb/hT3=2200 °R=1740.33 °F

Q: 14. List the given and required. Box the final answer.

A: Given S.GA=0.90S.GB=3

Q: In reference to the figure below, if us = 0.2 at the rear drive wheels B of the 1.5 Mg vehicle with…

Q: stion 2 Determine the force at Joint C (للشكل الموضح احسب القوة في العقدة C) hand written plz .. B…

Q: Two pounds of air initially at 200°F and 50 lbf/in2 undergo two processes in series: Process…

A: Solution.jpg

Q: 2.) An actual Rankine Engine is used to power a generator. The steam enters its turbine at 4 MPa and…

Q: The strain components εx, εy, and γxy are given for a point in a body subjected to plane strain.…

A: Given : εx = -1100 με εy = 490 με γxy = 1500 μrad θ = 34°

Concept explainers

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.

Question

In mechanical fluid

Gate AB in Fig.is 1.0 m long and 0.9 m wide. Calculate force Fon the gate and the position X of its center
of pressure.
7m
8m-
Oil,
5.g.=0.81
3m
1
10m
B
50⁰

Branch of science that deals with the stationary and moving bodies under the influence of forces.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Gate AB in Fig. (4) is 1.2 m long and 0.8 m into the paper. Neglecting atmospherie-pressure effects, compute the force F on the gate and its center of pressure position X. -6 m- 4 m Oil. SG = 0.82 8 m 1.2 m 40° Fig. 4
Gate AB in the figure is 1.2 m long and 0.8 m into the paper. Compute the force F on the gate and its center of pressure position X. 8 m ⒸMcGraw Hill Education. All rights reserved. No reproduction or Withere 6 m Oil, SG=0.82 1 m 4 m A1.2 m F X B 40°
Both the top of the tank and the end of the slanted tube are open to the atmosphere. If L = 3.65 m., x = 98 cm., y = 94 cm., SG1 = 0.98, SG2 = 1.88, what is the angle of tilt (in degrees) of the tube? Accepted answer ranges from 22.42-24.422. Show solution.
Note: Please state what formula you are using. And please be clear and detailed with your solution. Atleast explain. It will help me, thanks. Problem: A Triangular gate having a horizontal base of 1.30 m and an altitude of 2 m is inclined 45o from the vertical with vertex pointing upward. The base of the gate is 2.70 m below the surface of oil (s = 0.80). What normal force must be applied at the vertex of the gate to open it? Show figure
Problem 2. In reference to the figure, gate XY is 1.20m wide and 1.40m long. If the liquid in the tank is seawater (SG=1.03) at a head of 7m, detemine the following: a. total hydrostatic force "F" acting on the gate b. its line of action "h2" vertically from the liquid surface 3m
The tank in Fig. 2/is 3 m wide into the paper. Compute the hydrostatic (a) horizontal force component (b) vertical force component and (c) resultant force on quarter-circle panel BC. Consider y-9810 N/m b. 6 m Water Section A-A Fig. 1
What is the pressure at the bottom of 0.5m height fluid if the container moves 5m/s2 upward? Fluid has a density of 2000kg/m3 a. 13665Pab. 13258Pac. 14810Pad. 16145Pa
Curved panel BC in the figure is a 60-degree arc, perpendicular to the bottom at C. If the panel is 4 m wide, estimate the resultant hydrostatic force of the water on the panel. Use Ywater = 9.806 kN/m³ Answer: F = R=3m B 60° C 2 m Water
5. For the setup shown in the figure, what is the pressure pA if the specific gravity of the oil is 0.82? (S.G. of Hg 13.6) Air Oil Орen 4 m H,0 320 mm Hg- Figure for Prob. No. 5
A ship of displacement 36000 tonne carries oil fuel in four tanks 16.0 m long and 6.0 m broad, the tanks arranged with their length in the fore and aft direction. The specific gravity of the oil is 0.84, and the density of seawater inwhich the ship is floating is 1020 kgm-3. For a ship of this size, the metacentric height is at least 500 mm. What is the reduction of the metacentric height of the ship because of the oil that is contained in the tanks and how serious is this reduction? Please discuss further your conclusions.
2. The tank shown contains alcohol (SG=D0.78) and covered by a circular plug 1.2 m in diameter. Calculate the hydrostatic force F Am acting on the plug and its center of pressure. 8m 1.2 m 3. The gate as shown is 3 m normal to the page. It keeps the two liquids from mixing with each onough clocuro botween the oil and
Fluid mechanics, I need solutions in 15 minutes please. MCQ/Determine the horizontal and vertical components of the liquid pressure acting on the semicylindrical gate ABC, as shown in the figure. The width into the paper is 1 m. A-Fx = 257.430 kN and Fy = 59.801 kN B-Fx = 164.018 KN and Fy = 37.229 KN C-Fx = 269.894 kN and Fy = 65.526 KN D-Fx = 98.182 kN and Fy = 20.002 KN E-Fx = 234.789 kN and Fy = 52.418 kN F-Fx = 187.005 kN and Fy = 42.182 KN G-Fx = 119.956 kN and Fy = 25.550 KN H-Fx = 141.327 kN and Fy = 31.171 KN I-Fx = 288.147 kN and Fy = 69.098 KN J-Fx = 213.112 kN and Fy = 47.903 KN