SA5) What is the momentum of a vehicle if a force of 1000 N is applied on it in 0.50 seconds if it started from rest?

Q: Question 5 A fountain consists of a horizontal inlet pipe with a cross-sectional area, At, which…

A: The free body diagram of the block and nozzle is given below,

Q: locate the Centroid Por the following areas:

A:

Q: A thrust B journa 350N 0.25m B 0.35m 0.35m 0.15m 0.2m 0.Im P draw fbd

A: Draw free body diagram.

Q: A flanged bolt coupling consists of six 10-mm diameter steel bolts on a bolt circle 300 mm in…

A:

Q: Question 13 Solve the problem. Find the work done by a force of 200 pounds acting in the direction…

A:

Q: AWT305 x 41 standard steel shape is used to support the loads shown. Assume w = 46 kN/m, LAB = 1.2…

A:

Q: Q2: The pendulum consists of a 15 kg sphere and a thin bar of 5 kg. Calculate the reaction on pin O…

A:

Q: Consider an idealized engine that when supplied with heat at a temperature of 900 K deposits 50 J of…

A:

Q: Determine the equivalent state of stress on an element at the same Sig1 point which represents (a)…

A:

Q: Find an expression for the velocity of water leaving the sprinkler. Find an expression for the…

A:

Q: At the instant shown, the spring is un-deformed. Determine the change in potential energy if the 20…

A:

Q: The length and diameter of a suction pipe of a single-acting reciprocating pump are 5m and 10 cm…

A: Given: The length of suction pipe, Ls = 5 m The diameter of suction pipe, ds = 10 cm = 0.1 m The…

Q: The hollow shaft used in the system has the following conditions: Outer Ø: 110 mm Ø Allowable…

A:

Q: Your answer is partially correct. The strain components for a point in a body subjected to plane…

A: Find the principal strain and inplane shear stain and absolute shear strain .

Q: n. Calculate the force exerted by the seat

A: Given: V=670km/h R=1270m m=99kg   To find NA NB

Q: Two blocks are connected by a solid strut attached to each block with frictionless pins. If the…

A: Given : To find : Maximum weight of A to maintain equilibrium

Q: Figure In the figure shown, a bar ABC with negligible mass carries a 20 kN load and is supported by…

A: the allowable shear stress of the pin  in not given to get the diameter of the pin.please  put the…

Q: 7.59 A 6 in. pipe abruptly expands to a 12 in. size. If the dis- charge of water in the pipes is 5…

A:

Q: Three masses are attached to a 100-meter long beam as shown below. The mass of the bea, is 210…

A:

Q: 1.) An ideal regenerative cycle is executed with 56700 kg/hr of steam initially at 13.44 MPa and 594…

A:

Q: Which of the following expresses the equilibrium criterion for a closed system? o dG\T? O dS]u,v =…

A:

Q: The left field wall at a baseball park is 320 feet down the third base line from home plate; the…

A:

Q: A sprinkler system pumps water through a large pipe inlet with a diameter (di). The pipe then breaks…

A:

Q: Completely determine the resultant of the forces shown in the figure. Option: R= 957lb down to the…

A:

Q: The working conditions to be satisfied by a shaft transmitting power are (a) that the shaft must not…

A: GivenG=80000 N/mm2T=1MWattN=240rpmθlim=1oL=15dσallow=55 N/mm2

Q: A pump has a required NPSH of 3.0 m. Assuming that the pump is elevated at 3.5 m above sea level,…

A:

Q: 6. Consider the set – up where glycerin is poured in this U – shaped tube. It oscillates back and…

A:

Q: Assume the stabilizer of an airplane is a flat plate. If the   transition /critical RN 750,000, what…

A: Given data as per the question RN=750000v=44.7 mschord length =0.81 mrectangular stabilize having…

Q: The figure shows three 0.0112 kg particles that have been glued to a rod of length L=5.97 cm and…

A: Given data Mass of each particle  = 0.0112 kg Length of the rod = 5.97 cm = 0.0597 m

Q: Q9: A rope is wrapped around the edge of each of the 4 kg discs. If disc B is released from sleep,…

A:

Q: 9.5 Define bulk modulus K, and show that the decrease in volume of a fluid under pressure p is pV/K.…

A: Bulk Modulus(K) of a fluid is defined as the ratio of change in pressure to the volumetric strain…

Q: c) Draw the et and s-4 graphs if e = 0, s= 0 when -0. im )

A:

Q: The cross-sectional dimensions of the beam shown in the figure are a = 4.4 in., b = 4.9 in., d = 4.2…

A:

Q: (1) (2) |(3) a (4) (5) В с b A, = mm? 159 A2 = A3 = 33 mm? A4 = As = 46 mm? 26.5 mm Y, = Y2 = y3 =…

A:

Q: A cyclist jumps off the 25° slope track at 5m height, and with the speed 20 m/s. Calculate the time…

A:

Q: The simply supported beam shown consists of a W410 × 60 structural steel wide-flange shape [E = 200…

A: Write the formula for displacement at B due to the concentrated point load.…

Q: How can maching learning be incoraptred into Tesla?  2. Could Tesla benfit from automatic trading?…

A: Tesla's current AI solutions are based on unsupervised machine learning. Tesla is working on…

Q: Mohr’s circle is shown for a point in a physical object that is subjected to plane stress.  Each…

A: Given Each grid square is 280 psi in size

Q: Determine the force in the members GF, CF, and CD of the truss, also indicate if the members are in…

A: As per our guidelines, we are supposed to answer only first three subparts in case of multiple…

Q: deformation of bar wh

A: To find Total deformation of bar

Q: 1. Knowing that at the instant shown the velocity of collar A is 900 mm/s to the left, determine (a)…

A: Given:- Velocity of collar A = -(900 mm/s) I To Find:-  Angular velocity of rod ADB Velocity of…

Q: A UMC 50-80 circulator is operating at 1750 RPM. Flow is 50 GPM. Feet of head (friction) is 19 ft.…

A:

Q: The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1500…

A:

Q: m-/S, thế gap between the When the flow rate per unit wiath is Q' = lates is 5 mm, the device…

A:

Q: Draw the shear and moment diagrams for the loaded beam. After you have the diagrams, answer the…

A:

Q: Water is pumped at a rate 50o litres per minute through a 1 km horizontal, circular pipe of diameter…

A: Given:Q=500 l/minL=1 km =1000 md=20 cm =0.2 mf=0.05

Q: HUME WORK (2) Q1: The machine part of negligible weight is supported by a pin at A and a roller at…

A:

Q: SA2) A 2000-kg truck is parked 5.0 meters from one end of a bridge while a 1500-kg van is parked…

A: GIVEN: * 2000 Kg truck parked 5.0 m from one end. * 1500 kg Van parked 7.50 m from the opposite end.…

Q: Most modern electrical heating and cooling devices are provided with thermostat. What is the purpose…

A: given; Most modern electrical heating and cooling devices are provided with thermostat. What is the…

Q: a Gas Turbine Power Plant whoseefficiency is between 2096 to 356. Mhat is the compression ratio…

A: Answer : A is correct.

Layout

The layout is a way of organizing the elements, products, and raw materials in a design. The layout is the representation of information in a structural, logical, descriptive, coherent form.The layout is a mapping of various equipment arrangements, workstations, machinery, plants, and more. It secures the continuous movement of a product quantity along with the quality.