Give me both right solutios In circular pipe with 0.1 m diameter, pressure drop is 100 kg/m2 over 10 m wide with 0.1 m3 /s of turbulent flow rate. Find velocity at center of pipe cross section. Find turbulent τw at 0.02 m from pipe wall

Give me both right solutios In circular pipe with 0.1 m diameter, pressure drop is 100 kg/m2 over 10 m wide with 0.1 m3 /s of turbulent flow rate. Find velocity at center of pipe cross section. Find turbulent τw at 0.02 m from pipe wall

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In the pipeline in the figure, water is transmitted from a-tank to Bdepo with a flow rate of 40OL/s from plastic pipes. Pipe lengths are L1 = 20m, Lz=30m and bore diameters, D:=0.2 m, D2=0.4 m. Find the AH level difference between the two tank water surfaces. Take the kinematic viscosity of water v=4,25.10s m2/s. Loss of entry to the pipe Kbg=0,5 L1 =20 m D1=0,2m A ΔΗ Valve loss coefficient Kvalve = 10 valve Warehouse entry loss coefficient Kdg = 1 %3D Kao = [1- T Sudden expansion loss coefficient KAG L2=30m D2=0,4m
with a head loss of 7.5-m. Use iterative method to find the pipe diameter requires to keep a flow Q3: Oil, with (p- S950 kg/m'; v 2x10s m2/s), flows through horizontal smooth pipe of 80-m long rate of 0.332 m/s steadily flowing, (Start with initial guess of friction factor f-0.01)
The turbulent velocity profile in the pipe is given by the equation, ... Shear velocity 0,69 m/s, R = 8cm, viscosity is 0.001 kg/ms, density 900 kg/m3 calculate the maximum velocity and friction force for the pipe with 50m in length K=0.41, B=5.0.
A kitchen chimney, made of HINDWARE with exhaust pipe dia. of 90 cm supplies exhaust gas having flow rate of 1200 80 m3/hour. Length of exhaust pipe is 5m. Now BAJAJ Company wants to design a chimney to crater same flow rate but rectangular type with aspect ratio of 1.5. The length of exhaust pipes for both cases is assumed to be 5m. Also consider same friction factor for both the pipes as 0.182.Determine (i) the pressure drop for the HINDWARE duct. (ii) Considering the same pressure drop for the BAJAJ duct, determine its sides.
Jet water in Pipe with diumeter equal to Somm to velocity=30 - divided into fwo branches with (o-756) ancd the o ther with Cu.25Q] recPcetively un equal diameter. Compute fore CumPenen ts on the Plate sec Vュ

A pump delivers water from a tank (A)X water surface elevation-110m) to tank B (water surface elevation= 170m). The suction pipe is 45m long and 35cm in diameter the delivered pipe is 950m long 25cm in diameter. Loss head due to friction hf1 = 5m and h2 3m If the piping are from pipe(1)= steel sheet metal pipe(2)= stainless – steel Calculate the following i) ii) The discharge in the pipeline The power delivered by the pump.
A pipeline connecting three tanks contains 10 standard long elbows, 5 globe valves that is half open, and 3 gates valve that is 1/4 open. The line is commercial steel pipe, 40 mm internal diameter, length 200 m. The properties of the fluid are: viscosity 0.99 mNm-2 s, density 998 kg/m3. Calculate the total pressure drop due to friction using velocity heads method when the flow rate is 4000 kg/h and f = 0.0032.
3) Water at 20C° follow throw piping junction in the figure below. Entering section (1) at (0.0019m /sec). The average velocity at section (2) is (2.5 m/s). Apportion of the flow is diverted throw the shower head. Which contain (100 holes) of (1mm) diameter. The exit velocity from the exit shower head is 7.5 m/s assuming uniform shower flow estimate the diameter of section (2) (3) (2) (1)
roughness of this plastic. (4) What pressure drop is required in order to pump water at 20°C through a pipe 25 cm in diameter and length 1234 m at a rate of 1.97 m² sec 1? The pipe is horizontal and contains four standard-radius 90° elbows and two 45 elbows. (A standard-radius 90° elbow is roughly equivalent to the resistance offered by a pipe of length 32 diameters; a 45 elbow, 15 diameters) (5) Consider the steady-state flow of an incompressible Newtonian fluid through a horizontal tube of inner radius R and length L, as shown below: 1:52 AM 4/9/2021 ch
A saturated steam at 410K is being transported in a pipeline (brass drawing tubing) at a rate of 1 grams/second. Pipe has inside diameter of 0.025 m . The tube is 100m long. The pressure at the entrance is 80kPa. What is the value of G in kg/s.m2?. What is the value of friction factor? 3 significant figures. What is the % of pressure drop? Calculate the outlet pressure. Will it be under compressible or incompressible criteria.(use Perry's Handbook for the properties and constants) R = 8314J/kgmol.K; MW=18.02g/mol
A liquid a constant density 900 (kg/m3) is flowing at an unknow velocity V1 (m/det) through a horizontal pipe of inside diameter 10 (cm) and at pressure 5 (kg/cm2), and then it passes to a section of pipe in which the diameter is reduced gradually to 5 (cm) and the pressure is 3 (kg/cm2). Assumsing no friction losses, calculate the velocity V2 if the pressure difference is measured
A laminar flow element measures low gas-flow rates with a bundle of capillary tubes packed inside a large outer tube. Consider oxygen flowing at 84 ft3/min in a 4-in-diameter pipe. (i) Is the flow approaching the element turbulent? (ii) If there are 1000 capillary tubes, Length L, is 4 in, select a tube diameter to keep Reynold’s number below 1500 and also to keep the tube pressure drop not greater than 0.5 lbf/in2. (iii) Do the tubes selected fit nicely within the approach pipe?