Given: Calculate the available strength of a W14x90 with a strong axis unbraced length of 30.0 ft and weak axis and torsional unbraced lengths of 15.0 ft. The material properties and loads are as given W-shape column to carry an axial dead load of 140 kips and live load of 420 kips. The column is 30 ft long and is pinned top and bottom in both axes. Limit the column size to a nominal 14-in. shape. P₁ = 140 kips = kips 0.0£ =

Given: Calculate the available strength of a W14x90 with a strong axis unbraced length of 30.0 ft and weak axis and torsional unbraced lengths of 15.0 ft. The material properties and loads are as given W-shape column to carry an axial dead load of 140 kips and live load of 420 kips. The column is 30 ft long and is pinned top and bottom in both axes. Limit the column size to a nominal 14-in. shape. P₁ = 140 kips = kips 0.0£ =

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Situation 4: A W12x106 simply supported beam carries a uniformly distributed load. The properties of the section relevant to the problem are as follow: Use A50 steel and Cb - 1.14 d - 328 mm bf-310 mm tf = 25.1 mm tw = 15.5 mm kdes - 40.4 mm ry - 79.0 mm lx = 388 x 10^6 mm^4 ly - 125 x 10^6 mm^4 Sx - 2380 x 10^3 mm^3 Zx=2690 x 10^3 mm^3 J-3800 x 10^3 mm^3 Cw=2870 x 10^9 mm^6 1. Which of the following nearly gives the Design Strength Moment (LRFD) if the span of the beam is 2.5m? 878 KN-m 793 KN-m 836 KN-m 811 KN m
The beam shown in Figure is a W36 x182. It is laterally supported at A and B. The 300 kip load is a service live load. Using the unfactored service loads, a. Compute Cb. Do not include the beam weight in the loading. b. Compute Cb. Include the beam weight in the loading.
QUESTION 5 Column Design: Given: a solid circular column carrying a compressive load of 8500 lb with pinned ends. The length is 50 in. Use SAE 4140 OQT 1000 steel and a design factor of 3.0. a) Sy for the material given above is ksi
Question #5. Calculate the allowable axial compressive load for a stainless-steel pipe column having an unbraced length of 20 feet. The ends are pin-connected. Use A-11.9 inch, r-3.67 inch and Fy- 40 ksi. Use the appropriate Modulus of Elasticity (E) per material used. All the calculations are needed in submittal. O 212 kip O 202 kip O 196 kip 224 Wip
A compression member AB (HE 400 B) is pinned at both ends and braced in the weak direction as shown in the figure. Material and geometrical properties are given below. For the given loading and ASD load combination (PG+Pq=3500 KN), determine whether the section is satisfactory or not. Material: 5355 F355 MPa F 510 MPa E= 200000 MPa Section properties (HE 400 B): A: 19780 mm² d: 400 mm h: 298 mm t: 13.5 mm. tr: 24 mm b: 300 mm i,: 170.8 mm İy: 74 mm B X -BRACING IN THE WEAKDIRECTION
Q2 1- Check the following weather one way or two way 2- Calculate the design ultimate load Wu on the on the beams B3, B6 Assume slab load: Live load = 5 kN/m2 Dead load = 8 kN/m? Beam size 300x500 mm %3D B5 B6 B7 3.6 m |L 4.8 4 m 5m 5m BI B2 B4
A 1.5" x1.5" solid steel bar is made of a steel having an Fy = 50 ksi and an Fu = 65 ksi. It is loaded in tension by the following unfactored forces: • DL = 30 kips ● LL = 50 kips • SL 10 kips = Determine if the bar yields in tension. Assume LRFD. Use the ASCE 7-22 Load Combos and Factors.
Determine the maximum axial compression service load that can be supported by the column shown in Figure 1 if the service live load is 3 times bigger than the service dead load. Check that HSS 8x4x4 is a nonslender-element cross section and then use ACI Equations E3-2 or E3-3. 12 feet TMM HSS 8 X 4 X ¹/4 ASTM A500 Grade B Figure 1
A W12x72 is used as a column and is supported by a concrete pier with top surface dimensions of 16 inch x 16 inch. f’c of column is 4,000 psi and is to carry a total service load of 250 kips with a Live load / Dead load = 3/2. Use LRFD solution. If B=N=14 inches, what is the minimum required computed thickness of the column base plate in inch? Express your answer in three decimal places. Use A36 for base plate.
A column section is as shown in figure below. Z 320 mm- 20 mm Z ISMC 40 @ 49.4 kg/m The length of the column is 4.8 m. Using steel of grade Fe410, compute the design compressive load.
Use A36 steel and compute the nominal strength of the column shown. The member ends are fixed in all directions (x, y, and z). use recommended value of k. A 6.08 tw 0.282 b/t 5.87 ly 3.86 ro 4.93 no 11.5 C12X20.7 d 12.0 tf 0.501 h/t w 36.3 J 0.369 H 0.899 bf 2.94 K des 1.13 1x 129 Cw 112 rts 0.983 10' C12 x 20.7
Use A36 steel and compute the nominal strength of the column shown. The member ends are fixed in all directions (x, y, and z). use recommended value of k. A 6.08 tw 0.282 b/t 5.87 ly 3.86 ro 4.93 ho 11.5 C12X20.7 d 12.0 tf 0.501 h/t w 36.3 J 0.369 H 0.899 bf 2.94 K des 1.13 1x 129 Cw 112 0.983 10' C12 x 20.7