Given there are five (05) sample taken. The sample means (X-bar) are; 15.36,14.61,16.36,20.28, and 15.77respectively. Also, the corresponding ranges are; 10.79, 8.37, 4.81, 8.17, and 3.31 respectively. If the upper controllimit for X-bar chart is 20.59, what should be the most appropriate the sample size?О а. 5O b. 3О с. 4O d. 2O e. None is correctБЕNEXT PAGEhttps://elearn.sc321

Given - Sample means are 15.36, 14.61, 16.36, 20.28, 15.77 Average sample ranges are 10.79, 8.37,…

Answered: Given there are five (05) sample taken.…

Practical Management Science

6th Edition

ISBN:9781337406659

Author:WINSTON, Wayne L.

Publisher:WINSTON, Wayne L.

Chapter2: Introduction To Spreadsheet Modeling

Section: Chapter Questions

Problem 20P: Julie James is opening a lemonade stand. She believes the fixed cost per week of running the stand...

See similar textbooks

Similar questions

Need help on calculating control limits for x-bar and r-chart based on the samples below: Sample No X-BAR (Sample Mean) R (Sample Range) X-BAR R 1 28.2151942 9.5450186 2 30.5767201 11.1032318 3 29.0253789 5.52221327 4 29.9431791 6.27087883 5 29.947177 12.7568255 6 29.6848334 11.4927456 7 29.2539019 4.72514932 8 29.6694257 13.9330532 9 30.1590205 6.33461804 10 28.6867307 6.49522527 11 30.5960109 8.13717125 12 29.4390565 5.80286433 13 31.863426 3.40227918 14 32.3716448 8.62217828 15 29.7052597 10.0026916 16 30.0060069 4.25003967 17 32.8491753 4.6515662 18 33.5023103 9.62764088 19 28.1876404 9.6980397 20 30.5043768 6.46724539 21 29.6856417 7.65071069 22 32.5728395 9.2483604 23 28.2363719 7.54975234 24 29.6579999 11.3224787 25 28.1319897 13.213391 26 28.8811004 8.08405181 27 31.6730765 12.9865678 28 28.2078142 5.96315947 29 27.9430689 7.39518992 30 29.6269815 9.48802129 31 34.3599108 7.66563648 32 28.2423234 7.34122645…
Checkout time at a supermarket is monitored using a mean and a range chart. Six samples of n = 20 observations have been obtained and the sample means and ranges computed: Sample Mean Range Sample Mean Range 1 3.06 .42 4 3.13 .46 2 3.15 .50 5 3.06 .46 3 3.11 .41 6 3.09 .45 a. Using the factors in Table 10.3 , determine upper and lower limits for mean and range charts. b. Is the process in control?
Auto pistons at Wemming Chung's plant in Shanghai are produced in a forging process, and the diameter is a critical factor that must be controlled. From sample sizes of 5 pistons produced each day, the mean and the range of this diameter have been as follows: Day Mean (mm) Range R (mm) 158 4.3 151.2 4.4 155.7 4.2 153.5 4.8 156.6 4.5 What is the UCL using 3-sigma?(round your response to two decimal places). 1. 2. 4.
Five samples of size 4 were taken from a process. A range chart was developed that had LCLR = 0 and UCLR = 2.50. Similarly, an average chart was developed with the average range from the five samples, with LCL = 15.0 and UCL = 24.0. The ranges for each of the five samples were 1.75, 2.42, 2.75, 2.04, and 2.80, respectively. The values of the sample average for each sample were 19.5, 22.3, 17.4, 20.1, and 18.9, respectively. What can you tell management from this analysis? The process variability is out of control, and we cannot make a statement about the process average. The process variability is out of control, but the process average is in control. The process variability and the process average are out of control. We cannot tell if the process variability or the process average is out of control. Need the answer in 10 minutes, if possible. Please
< Refer to Table S6.1 - Factors for Computing Control Chart Limits (3 sigma) for this problem. Sampling 4 pieces of precision-cut wire (to be used in computer assembly) every hour for the past 24 hours has produced the following results: Hour X 1 2 3 4 5 6 R 3.25" 0.65" 3.00 1.23 3.32 1.43 3.39 1.26 3.07 1.17 2.96 0.37 Hour X R Hour R Hour 7 2.95" 0.48" 13 X 3.11" 0.90" 2.73 1.36 19 20 8 2.55 1.18 14 9 0.71 3.12 1.11 21 3.12 2.85 15 16 10 1.38 2.74 0.50 22 11 2.83 1.22 17 2.86 1.38 23 12 3.07 0.45 18 2.64 1.29 24 X 4.51" 2.89 2.65 3.18 3.04 2.54 R 1.56" 1.14 1.13 0.51 1.58 1.02 Based on the sampling done, the control limits for 3-sigma x chart are (round all intermediate calculations to three decimal places before proceeding with further calculations): Upper Control Limit (UCL) = inches (round your response to three decimal places).
Factors for Computing Control Chart Limits (3 sigma) Auto pistons at Wemming Chung's plant in Shanghai are produced in a forging process, and the diameter is a critical factor that must be controlled. From sample sizes of 10 pistons produced each day, the mean and the range of this diameter have been as follows: Day Mean x (mm) Range R (mm) 1 156.9 4.2 2 153.2 4.6 3 153.6 4.1 4 155.5 5.0 5 156.6 4.5 Part 4 c) What are the (UCLx) and (LCLx) using 3-sigma? (UCLx) = mm (round your response to two decimal places). (LCLx) = mm
In a fabric manufacturing factory, the quality control process using control charts from SPC. In an hour there are a total of 5 samples are taken each having 5 observations regarding the thickness of fabric in measured in millimeters. In a particular hour, the sample means (X-bar) are noted to be: 172.11, 219.51 . 208.24, 112.44 and 123.30 respectively. In the same sample, the corresponding ranges are: 13.1713.3815.34, 13.04, and 13.02 respectively What are the lower and upper control limits for the R chart?
In a fabric manufacturing factory, the quality control process using control charts from SPC. In an hour there are a total of 5 samples are taken each having 4 observations regarding the thickness of fabric in measured in millimeters. In a particular hour, the sample means (X-bar) are noted to be: 172.11, 219.58, 208.24, 112.44, and 123.30 respectively. In the same sample, the corresponding ranges are: 13.17, 13.38, 15.34, 13.04, and 13.02 respectively What are the lower and upper control limits for the X-bar chart? O a. None is correct O b. 143.55, 165.47 Oc. 144.78, 159.11 O d. 157.21, 177.05 O e. 146.01, 157.87 Of. 142.92, 160.66
In a fabric manufacturing factory, the quality control process using control charts from SPC. In an hour there are a total of 5 samples are taken each having 4 observations regarding the thickness of fabric in measured in millimeters. In a particular hour, the sample means (X-bar) are noted to be: 172.11,219.58, 208.24, 112.44, and 123.30 respectively. In the same sample, the corresponding ranges are: 13.17, 13.38, 15.34, 13.04, and 13.02 respectively What are the lower and upper control limits for the R chart? O a. 0,31.47 O b. 0,30.99 Oc. None is correct O d. 0,29.17 O e. 0,31.17 O f. 0,28.17
Determine the upper and lower control limits for a mean chart, if you choose to use a sample size of 5. Set z=3
1. The data shown in Table 1 are x and R values for 20 samples of size n= 5 taken from a process producing bearings. The measurements are made on the inside diameter of the bearing, with only the last three decimals recorded (i.e., 31.6 should be 0.50316). Please show all your work for full credit. (a) Set up x and R charts on this process. Does the process seem to be in statistical control? If necessary, revise the trial control limits. (b) Assume that diameter is normally distributed. Estimate the process standard deviation. Sample R Sample R 1 31.6 4 11 29.8 4 33.0 3 12 34.0 4 35.0 4 13 33.0 10 4 32.2 4 14 34.8 4 5 33.8 38.4 31.6 15 35.6 7 3 16 30.8 7 4 17 33.0 5 8 36.8 10 18 31.6 3 9. 35.0 15 19 28.2 9 10 34.0 6 20 33.8 Table 1: Bearing Diameter Data
Cartons of Plaster are supposed to weigh exactly 32 ounces. Inspectors want to develop process control charts. They take five samples of six (6) boxes each and weigh them. Sample means (X-bar) are: 33.8, 34.6, 34.7, 34.1, and 34.2 respectively. Also, the corresponding ranges are: 1.1,0.3, 0.4. 0.7, and 0.3, respectively. The lower and upper control limits of the xbar-chart are respectively O a. None is correct O b. 30.11 and 40.15 O c. 34.01 and 34.55 O d. 33.12 and 34.12 O e. 37.01 and 39.23

SEE MORE QUESTIONS

Recommended textbooks for you

Practical Management Science

Operations Management

ISBN:

9781337406659

Author:

WINSTON, Wayne L.

Publisher:

Cengage,

Operations Management

ISBN:

9781259667473

Author:

William J Stevenson

Publisher:

McGraw-Hill Education

Operations and Supply Chain Management (Mcgraw-hi…

Operations Management

ISBN:

9781259666100

Author:

F. Robert Jacobs, Richard B Chase

Publisher:

McGraw-Hill Education

Practical Management Science

Operations Management

ISBN:

9781337406659

Author:

WINSTON, Wayne L.

Publisher:

Cengage,

Operations Management

ISBN:

9781259667473

Author:

William J Stevenson

Publisher:

McGraw-Hill Education

Operations and Supply Chain Management (Mcgraw-hi…

Operations Management

ISBN:

9781259666100

Author:

F. Robert Jacobs, Richard B Chase

Publisher:

McGraw-Hill Education

Business in Action

Operations Management

ISBN:

9780135198100

Author:

BOVEE

Publisher:

PEARSON CO

Purchasing and Supply Chain Management

Operations Management

ISBN:

9781285869681

Author:

Robert M. Monczka, Robert B. Handfield, Larry C. Giunipero, James L. Patterson

Publisher:

Cengage Learning

Production and Operations Analysis, Seventh Editi…

Operations Management

ISBN:

9781478623069

Author:

Steven Nahmias, Tava Lennon Olsen

Publisher:

Waveland Press, Inc.

SEE MORE TEXTBOOKS