Pin idBm=Pino lagI0 log Pin(2)Pnw-0.316wShift log () as2525Pinmw = 316.229- The diagram below represents the first three stages of a typical AM or FM receiver. Findthe following quantities.PouantennagerialمسقبلreciverP37attenuatorP,=1 pWPIP2RFAmplifierArr 100MixerIF AmplifierAp 10,000PAnt-171X10Ap=0.2PoutAT=pico watts-12a) Arand AT dB•and 4

In this question, We need to determine the output power P1, P2 and Pout? Input power Pi= 1p W Gain…

hitt log (T0) 25 -1000 (25) PinmW= 1D Pinmw= 316.22 9- The diagram below represents the first three stages of a typical AM or FM receiver. Find the following quantitics. antenna gerial مسقبل AP3- reciver P3 7attenuator P pW RFAmplifier A= 100 Mixer IF Amplifier Ap 10,000 -17 Apz 0.2 P. ant Pout a) 4 ond 4 Pico watts

hitt log (T0) 25 -1000 (25) PinmW= 1D Pinmw= 316.22 9- The diagram below represents the first three stages of a typical AM or FM receiver. Find the following quantitics. antenna gerial مسقبل AP3- reciver P3 7attenuator P pW RFAmplifier A= 100 Mixer IF Amplifier Ap 10,000 -17 Apz 0.2 P. ant Pout a) 4 ond 4 Pico watts

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. The Voltage spectrum of FM signal is shown in Figure 1. The maximum amplitude of modulating signal is 5V. Calculate the bandwidth , modulation index ,Carrier frequency, modulating frequency and specify the type of Modulator(narrow band or wide band). 1.54 4.06 4.06 2.45 2.45 0.91 0.91 0.21 0.21 192 194 196 198 200 202 204 206 208 KHz
The instantaneous frequency of an FM-modulated signal will vary between fmin = 99.98MHZ And fmax = 100.02MHZ when the modulating signal is a sine wave with fm = 3KHZ .determine a. Carrier frequency (3) b. Frequency deviation c. Modulation index
The figure below shows the frequency spectrum of an AM signal. 15V 6V 6V 475kHz 480kHz 483kHz 488kHz a) Draw the frequency spectrum of the modulating signal and label completely b) Calculate the effective voltage of the AM signal c) What is the percent modulation?
Please explain the waveforms, what are the reason why does the 3rd waveform is attenuated. 1st waveform: Carrier signal (2Vpk,20 kHz) 2nd waveform: Information signal (1Vpk,1kHz) 3rd waveform: Receiver signal
According to the figure below determine the following 1. What is the name of this type of modulation - 2. Determine the modulation index 3. Determine the amplitude of carrier and the amplitude of information signals 4. Write down the mathematical form of the signal assume the carrier frequency 10 MHz and information frequency 1 KHz. 5. If we want change the modulation index to be 1, how would your answer to parts three & four change? Amplitude 1.5 0.5 -0.5
Design Armstrong indirect FM modulator to generate an FM signal with fc = 400 MHz and Af = 97.2KHz. A NBFM generator of fc1 = 100KHz and Af₁ 25Hz. Fifth frequency tipplers can be used as multipliers, any number of frequency doublers and a local oscillator with tuning range (400-1500) KHz is readily available for frequency mixing. =
Derive the frequency reuse factor for a triangular cell
For an AM DSBFC transmitter produces an output as in Figure Q1(d) with resistance load, RL of 102 that is modulated simultaneously by two modulating signals with coefficients of modulation mı = 0.5, and m2 = 0.8. Determine the total transmitted power and power spectrum. 30V Figure Q1(d): Ampltide modulation
A10.5*107 Hz carrier signal is frequency modulated by a 20KHz sine wave. The resultant FM signal has a frequency deviation of 110.6KHz. Calculate (12 a) What type of modulation? b) Determine modulation index and bandwidth c) Determine power at 105MHz d) Determine the highest and lowest frequency of FM signal
A 100MHZ carrier is frequency modulated by 10 KHz wave. For a frequency deviation of 50 KHz, calculate the modulation index of the FM signal. 100 70 90 50 Carson's rule is used to calculate Signal to noise ratio O Noise figure Bandwidth of FM signal Modulation index
FM modulator is used to transmit a cosine message signal with 4V amplitude and 20Hz frequency. The carrier is a cosine signal with an amplitude of 10V and a frequency of 2000Hz. What is the power of the FM modulated signal?
1. The Voltage spectrum of FM signal is shown in Figure 1. The maximum amplitude of modulating signal is 5V. Calculate the bandwidth , modulation index „Carrier frequency, modulating frequency and specify the type of Modulator(narrow band or wide band). 1.54 4.06 4.06 2.45 2.45 0.91 0.91 0.21 0.21 192 194 196 198 200 202 204 206 208 KHZ Figure 1 Reference: (1] Fundamental of Frequency modulation, Pages 150- 163, Principles of Electronics Communication system, Louis E. Frenzel Jr. Check Moodle assignment link for book. DFocus