Answered: How much "steel per foot" is there in a…

Engineering

Civil Engineering

How much "steel per foot" is there in a slab with #4 bars (area=0.2 in2) spaced 8 inches on center?

Architectural Drafting and Design (MindTap Course List)

7th Edition

ISBN:9781285165738

Author:Alan Jefferis, David A. Madsen, David P. Madsen

Publisher:Alan Jefferis, David A. Madsen, David P. Madsen

Chapter42: Common Commercial Construction Materials

Section: Chapter Questions

Problem 42.26Q

See similar textbooks

Related questions

Q: Define the Significance of Shear Strength ?

A: Solution: Shear strength is defined as the strength of the material against the structural failure…

Q: For the isolated Square panel shown in figure:- 1. Check the slab thickness, (t=300"), 10.0" 2.…

A: Given values: fy=420 MPa f'c=30 MPa LL=3 KN/m2

Q: ) = 1.50 ksi. Determine the dimension of the timber. if it is rectangular a D-width ratio of 1.5.…

Q: What force is required to punch a ½ inch hole on a 3/8 thick plate if the ultimate shearing strength…

A: Given data in question Shearing strength of plate 42,000 psi Thickness 3/8 inches Diameter 1/2…

Q: Four 28 bars are to be placed on a single layer in a beam having a width of 350 mm with shear…

A: Clear cover It is the distance between the outer face of any RCC member (column, beam, slab, and…

Q: The garage measures 20'0" x 20'0" . It needs concrete poured to a depth of 6 inches. The garage…

A: Given Data, Cross section of garage = 20×20 Cross section of Garage door= 16×8 Depth of concrete to…

Q: What size does an opening in concrete have to be before a deduction is made from the volume of…

A: Where there is an opening in a form system, no deduction is made from the total area of the forms if…

Q: What purpose do stirrups serve when installing reinforcing bars in a form?

A: The reinforcement in the beam in the form of steel bars is used. The bottom bar performs the…

Q: Estimate the depth of a waffle slab.

A: The 2 way solid slabs having large span and ribbed system is called as waffle slab.

Q: What is the minimum thickness for a residential slab?

A: A concrete slab is normally used for the floor system of industrial or residential structures. It…

Q: Discuss the procedure for erecting pre-cast concrete units and the types of connections used?

A: Nowadays, construction industries, to avoid site work and site activity use the precast concrete…

Q: Define how to determine the required depth of embedment of the anchor bolts into the concrete ?

A: Anchor bolts are used to move loads through components like ledgers, sills, including supporting…

Q: Identify how openings are spanned in masonry walls?

A: Spanning of openings: Openings for doors , windows and access openings must be bridged over by some…

Q: how is a foundation post proyected from the moisture in the concrete support

A: The way by which protection of foundation post is done from moisture in the concrete support.

Q: 1. Determine the number of 7 5/8-inch-high by 5 5/8-inch-wide by 15 5/8-inch-long concrete blocks…

A: Wall is an basic structural member of building/structure.It helps in bearing load and its transfer…

Q: Define the Hollow core plank system ?

A: Hallow core plank system : A hallow core slab also known as a voided slab, hollow core plank or…

Q: Describe about the steel sheeting sections.

A: steel sheeting section:

Q: What is sandstone?

A: The sedimentary rocks are one of the geological classifications of rocks. The sedimentary rocks are…

Q: Elaborately explain the term one-way slab in relation to reinforced slab design

A: Question : Elaborately explain the term one-way slab in relation to reinforced slab design.

Q: What is the required minimum thickness (mm) of a 3.2m long, simply supported one-way slab if its…

A: Concrete slab The concrete block may be a current structural part gift in numerous buildings that…

Q: Using allowable stress design, the maximum vertical load (lb) per stud is most nearly: (A) 2,700 (B)…

Q: Q2/ Answer the followings with drawing sketch: A/ briefly explain what is construction joint and…

A: Construction Joint: It is type of concrete joint that is used when a new section of concrete is…

Q: How are masonry units supported over openings in a wall?

A: With the help of lintel the masonry units are supported over the wall opening. The formation of…

Q: one-way slab to support a load

A: To design the slab for the given specifications

Q: For a 700mm X 700mm slab, provide both longitudinal, and transverse reinforcement as well as spacing…

A: A slab is a RCC structural member which is used to transfer the live load to beam and ultimately to…

Q: Calculate the number of bricks/square foot 3 518" x 2 114" x 75/8" brick %3D 3/2" wide joints

Q: What is the crank length in the slab?

A: Answer Crank is the little or slight bending of the reinforcement that is used for maintaining the…

Q: Define the purpose of skin reinforcement for deep beams?

A: Skin reinforcement is provided to ensure the elimination of crack formation on the surface of the…

Q: Define the IS code for Plain and Reinforced Concrete ?

A: IS 456-2000 Plain and Reinforced Concrete - is an Indian Standard code of practice used in general…

Q: A 5.5m x 6m slab has main reinforcements running in both directions. Estimate for the materials…

A: Given data: Steel rod: diameter = 12 mm length = 9 m Slab: L=6 m B= 5.5 m Spacing = 15 cm

Q: The owner of a commercial lot wants to fence the frontage of his lot 4.00 m length x 2.60 m from…

A: The values given in the question are as follows: Length of the fence(L)=4.0 m or 400 cm Height of…

Q: Does waterproofing works comes after slab has been laid out or before?

A: Waterproofing is done in order to protect the structure from water intrusion and structure damage.…

Q: Design rectangular sections for the beams, loads, and p values shown. Beam weights are not included…

A: Beam: A lintel is a lateral element that spans an aperture and bears a weight that could be a brick…

Q: Can you expand these? especially the second part?

Q: Give atleast 5 comparisons or differences between Portal Method and Cantilever Method of structural…

A: Cantilever method : For thin buildings that are likely to deform in flexure mode, the cantilever…

Q: beam

Q: What is the error in (2 bonding? (1) The leveling error (2) The mortar error(3) foundation error

A: During a construction process, errors may take place due to various reasons like inaccuracy during…

Q: 3. Please describe the requirements for the removal of formwork.

A: Formwork should not be removed until the concrete has developed sufficiently strength to support all…

Q: How to install Metal Forming in floor slab?

A: metal forming is the process of changing the surface of the metal by using mechanical instruments.…

Q: Determine the number of blocks needed to build the exterior stacked block wall from the footing to…

A: Solution:

Q: What are the functions of column capital in Flat slab?

A: The function of column capital are: 1. To increase the shear strength of the slabs.

Q: Question 8 A sample slab section view is shown below: *4010"EW 30 Felt Joint El. See What should be…

A: The second and third options are wrong because the reinforcements are shown in only one direction in…

Q: B4 8000 AREA 1 AREA 2 B1 B2 B3 || || || || || || || || B5 2000 AREA 3 1 I B6

Q: What type or line qualify is typically used to represent beam pockets?

A: To determine the type or line qualifies is typically used to represent beam pockets as,

Q: Define Shear load,

A: Shear loads are characterized as powers applied to an example digression to the stacking hub, yet…

Question

How much "steel per foot" is there in a slab with #4 bars (area=0.2 in²) spaced 8 inches on center?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 Given

VIEW

Step 2 Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Similar questions

What is the recommended minimum diameter (mm) for temperature bars in one way slab? Express your answer in whole number, no need to indicate the unit. Determine the maximum spacing (mm) of temperature bars if it has a thickness of 125mm. Round of your answer to a whole number.
Describe the Effect of Tension Cracks.
Does the admixture affect the compressive strength? How?
6. ESTIMATION OF QUANTITIES OF STEEL & R.C.C. ELEMENTS EPU Example 1: Estimate the Slab reinforcement for the given figure below. All the straight bottom bars are 10mm@400mm c/c. All offset bars 12mm@400mm c/c, All Additional Top bars 12mm@400mm c/c. The slab thickness is 150mm. Assume cover is 25mm & wall thickness20cm 0.45 0.45 3.70 4.70 0.45 0.45 3.70 5.20 3.10 1.60 150
Referenced concrete n=16
What are control joints and isolation joints? Explain the purpose and typical locations for each in a concrete slab.
For the figure shown, if the resultant of the forces is acting at the slab center. Please attach detailed/clear solutions. Thanks.
Define the process of Development of Reinforcement bar stresses ?
Explain the how to calculate the pitch of the helical reinforcement.
Wall-Wide What is the volume of concrete based on the attached section? • Length of the footing is 31000 • Strip footing is 550 wide by 220 tall Wall is 1300 high x 250 wide All dimensions are in mm Strip Footing - Wide Answer: Wall-High Strip Footing - Tall The answer is to be in the format xx.xx (round to 2 decimal places). Do not enter the units of cu. m.
The total length of exterior walls of a residential building is 650 lf. The 8-foot long 2x4 studs are spaced 16 in. OC or less. The drawing of the building shows there are 20 corners requiring three studs. Studs are installed on single 2x4 bottom sill plates and capped by double 2x4 top plates for the entire length of the walls. Both bottom and top plates are 16-ftlong each. Prepare a list of materials for the wall studs, corner studs, sill plates, and top plates. For each of the materials, show the nominal dimension, number of pieces of each length, the length ofa lumber, and the total linear feet. Estimate the total direct cost and cost per linear foot of wall for furnishing and installing the studs and plates. Assume $0.75/bf for lumber, $30.00/hour carpenters, and $24.00/hr for laborers. Use the average value in Table 12.10 for the labor-hours
37 A simply supported beam 300 mm wide, 500 mm deep and spans 5.5 m supports a service super imposed dead load of 8 kN/m and service live load of 7 kN/m. Concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa. Concrete cover to bar centroid is 70 mm. Determine the required amount of tensile reinforcement in mm^2 as per provisions of NSCP 2015. Write your final answer to the nearest whole number.