Identify 3 car’s components in general, one subjected to tension, the 2nd to compression, and the 3rd component subjected to a shear force. Find a suitable factor of safety of your components and calculate the working stresses and strains for each of your components. Assume values to do the caculations. How does an increase in operational temperature affect your results?

Q: The engineering stress and strain are defined relative to the instantaneous area and length of test…

A: At higher temperature, strength and strain hardening is increased whereas ductility is decreased…

Q: Q13- Calculate the work done in frictionless compression of a solid cylinder 40 mm high and 15 mm in…

A:

Q: An aluminum bar (6061-T4) is initially 225.00 mm long at a temperature of 20 C. It is placed between…

A: Given:Initial temperature of aluminum, Ti=20o CFinal temperature of  aluminum, Tf=205o CCoefficient…

Q: 50.800mm is pulled in tension. Using the load-extension characteristics of Table 1 sand answer A…

A: Given-Data:- Stainless-Steel Diameter =12.8mm Guage length = 50,800mm To-Find:- 1) Plot…

Q: Tensile test under 40,000 N load was applied to a low carbon steel with a sample diameter of 6 mm.…

A: load on carbon steelP=40000Ndiameter of steel rod d1=6mmdiameter of specimen under load decrease to…

Q: Using the following concepts: torsion of a solid circular cross-section, Mohr's circle, and failure…

A: Chalk is a brittle material which is weaker in tension than shear. When the chalk is twisted pure…

Q: 3. For steels, the endurance limit is approximately half of the tensile strength, and the fatigue…

A:

Q: A cylindrical brass rod with a minimum tensile strength of 450 MPa, a ductility of at least 13% EL…

A:

Q: 11.4 mm (0.45 in.) in diameter is to be cold worked by drawing; the circular cross section will be…

A:

Q: Wire stock of initial diameter = 3.175 mm is drawn through two dies each providing a 0.20 area…

A: Introduction: The flow stress is the stress at which the wire yields or deforms plastically, and it…

Q: A 32 inch long, solid steel circular shaft, 3 inches in diameter, is twisted through an angle of…

A:

Q: A certain force F is applied at D. OABC bar is made of AISI 1035 steel, having yield strength of 560…

A:

Q: (a) Draw two Engineering Stress - Engineering Strain graphs: one for a ductile metal and one for a…

A:

Q: Compute the tensile strength, yield strength and ductility (%EL) of a cylindrical copper rod if it…

A: Given data: - The initial diameter of rod is di = 15.2 mm. The final diameter of the rod is df…

Q: Required information A ductile hot-rolled steel bar has a minimum yield strength in tension and…

A:

Q: Solid and hollow shafts are most often used to provide power transmission of the rotating motion…

A: Solution(1) There is nothing mention to calculate about the AB port of shaft     so we will only…

Q: HW Calculate the mean depression diameter in Brinell hardness test when the BHN=255 kg/mm2, and the…

A:

Q: A compression test is performed on a 2” diameter by 5” long bar of an unknown metal.  At the end of…

A: Given:d1=2 inl1=5 inl2=3.5 inK=250 MPan=0.4a)Volume before compression=volume after compression…

Q: A 1040 steel has been heat-treated to a yield stress of 900 MPa and a tensile yield strength of 1330…

A: Given:- Yield stress=900 MPa Tensile yield strength=1330 MPa Endurance limit=620 MPa To find:- To…

Q: a matensetic steel (Kic= 110MPavm) whose fatigue crack growth rate is given on the attached sheet. A…

A: Martensite is a crystalline form of steel that is extremely hard. It is named after Adolf Martens, a…

Q: For a tensile test it can be shown that the percent cold work (%CW) is related to strain according…

A:

Q: 4. In rolling operation, large diameter roll induces.. on the surface of the rolled part. b. tension…

A: Explanation : During rolling operation , due to rolling extrusion force applies over the surface to…

Q: The figure below shows the stress-strain behavior of a mild steel (the insert shows part of the same…

A: *As per our guidelines we are supposed to answer first three sub-parts of the question. Kindly…

Q: Q3:A/what are the Factors that affect fatigue life? And what are the solutions for them?

A: Fatigue life: It is scientific term for an mechanical object which relates how long a material will…

Q: For the given modified Schewedoff model: E, E, a. Derive the governing equation for the model b.…

A:

Q: Consider the tensile stress strain curves in Figure 8-20 labeled 1 and 2 and answer the following…

A: (a) Work hardening is a process used in order to increase the hardness of the workpiece by…

Q: A

A:

Q: a) A bicycle frame is being designed to carry a pedal force of 800N. Assuming axial loading only,…

A:

Q: compute the tensile strength and ductility of a cylindrical copper rod if it is cold worked such…

A:

Q: 1) For a certain metal, the strength coefficient= 700 MPa. A tensile specimen of the metal with gage…

A: Given: Strength coefficient (k)=700MPaGauge length (L)=150mmStretched length (L0)=207mm

Q: Stress in the x direction = Blank 1 Stress in y direction ,=Blank 2 Shear Stress on the weld 7 =…

A:

Q: A rotating bar made of steel with ultimate strength of 600 MPa is subjected to a completely reversed…

A: Given that ,Sut=630 MPa=630=N/mm2Se=300MPa=300N/mm2N=90000 cycles

Q: A cylindrical rod of non cold-worked brass having an initial diameter of 6.4 mm (0.25 in.) is to be…

A: Given:do=6.4 mmdi=5.1 mm

Q: Q: Consider an 18-8 Mo stainless steel component (Figure below) that is exposed to an allowable…

A: Given: Allowable stress level = 110 MPa Rupture lifetime = 1 year.   To find: Whether the metal is…

Q: Is the Paris power law (Eq. 10-3) relevant for all conditions of fatigue crack growth?

A: Paris' law (also known as the Paris–Erdogan equation) is a crack growth equation that gives the rate…

Q: A 12.5 mm diameter cylindrical rod fabricated from a Red brass alloy is subjected to a repeated…

A: Given: Diameter of cylinderical rod = 12.5 mm Fatigue life of rod = 2,000,000 cycles Material : Red…

Q: A round AB bar (L = 600 mm in length and with Ø = 55 mm of diameter) is machined from the…

A: According to terms and conditions of bartleby we can only provide upto 3rd part. thank you

Q: A metal wire of diameter 1.2 mm is used to carry a load of 1100 N. If the material of which the wire…

A:

Q: steel bar is desired to be formed until it has a final length of 1.8m. What length sould the bar in…

A:

Q: Determine the indentation diameter and the surface area of indentation of a copper material…

A: (i) Write the expression of the BHN,   BHN=2FπDD-D2-d2Here,F=Load in kgD=Diameter of steel ball…

Q: A hot rolling mill has rolls of radius = 105mm. It can exert a maximum force =1219625 Newton. The…

A: We have to determine  (a) maximum possible draft(b) associated true strain(c) maximum rotational…

Q: Example: Convert the change in length data in Table 3-2 to engineering stress and strain and plot a…

A: Given data

Q: A steel bolt and sleeve assembly are shown in the figure. The nut is tightened up on the tube…

A:

Q: For a certain metal the strength coefficient K = 600 MPa and the strain hardening exponent n = 0.20.…

A: Given               The strength coefficient K = 600 MPa    The strain hardening exponent n = 0.2…

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.